2016 KIA K900 sensor

DRIVER’S PA NEL
9*IF EQUIPPED
A LWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFETY WARNINGS.
www.KuTechVideos.com/kh13/2016
BLIND SPOT
DETECTION SYSTEM
VIDEO
To view a video on
your mobile device,
snap this QR Code or
visit the listed website.
Refer to page 2 for
more information.
Blind Spot Detection (BSD) System*
The Blind Spot Detection (BSD) system uses radar sensors to
monitor surrounding areas and help alert the driver to nearby
vehicles before changing lanes. With the ENGINE STA R T/
STOP button in the ON position, press the BSD button
B to
turn the system ON. The button light will illuminate.
The system will activate when the vehicle is traveling more
than 20 mph and will alert the driver if another vehicle is
detected by the radar s en s o r.
1st-stage alert: When another vehicle is detected within the
BSD system boundar y, a yellow indicator will illuminate
A on
the outside rearview mirrors.
2nd-stage alert: When 1s t stage alert is on and the
driver activates a turn signal, a ashing red indicator will
illuminate
A on the outside rearview mirrors and the
system will sound an alert.
\fear Cross \br a f f i c Alert ( \f C \bA )
If the Rear Cross Tr a f c Alert ( RC TA ) system sensors detect
vehicles approaching from the left or right side, the system
will sound an audible alert, the warning indicators on the
outside rearview mirror will illuminate and a message will
appear on the LCD screen, under these conditions:
§ When the vehicle is in Reverse
§ When the vehicle moves backwards from a parked position
§ When the vehicle is moving less than 6 mph
REMINDER: The RC TA feature can be turned
OFF/ON by pressing the BSD button B.
A
B
Quick \bip
The BSD system will activate when:
1. The system is turned on
2. Vehicle speed is above approximately 20 mph
3. Other vehicles are detected on the rear sides of
the vehicle
REMINDERS:
- The BSD system will not issue a warning if the vehicle
speed is 6 mph or more above the surrounding vehicles
- When the BSD is ON and the ignition is cycled, the BSD
system returns to ON
(Buttons located on driver’s panel,
left of the steering wheel)
29319_Text.indd 911/6/15 10:20 AM

STEERING WHEEL CONTROLS
17*IF EQUIPPED
A LWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFETY WARNINGS.
A
Windshield Wipers & Washers
To operate:
§ Move lever up/down to change wiper modes
M I S T: Single wipe
OFF: Wiper off
AUTO: Auto Rain Sensing LO:
Slow wipe
HI: Fast wipe
§ Pull to spray and wipe
Quick Tips
- When the ENGINE START/STOP button is in the
ON position and the wiper switch is in AUTO
mode, the wiper will automatically operate once
to perform a self-check of the system
- Set the wiper to the OFF position when the wiper
is not in use
- If going through a car wash, remind the
attendant to keep the vehicle in Neutral (N)
and keep the engine running. Also, disable the
Power Trunk lid control using the button inside
the glove compartment, turn off the auto rain-
sensing wipers and fold in the mirrors
Au\fo Rain Sensin\b
The rain sensor located on the upper end of the windshield
glass senses the amount of rainfall and controls the wiping
cycle for the proper interval. The more it rains, the faster the
wiper operates. When the rain stops, the wiper stops.
To turn ON the auto rain-sensing wipers, move lever up/down
to AUTO.
To adjust the auto rain-sensing wiper speed setting, move
the speed control switch
A up/down.
www.KuTechVideos.com/kh13/2016
AUTO RAIN-SENSING
WINDSHIELD WIPERS
VIDEO
To view a video on your
mobile device, snap this
QR Code or visit the listed
website. Refer to page 2
for more information.
LCD Con\frols and Modes
The LCD modes B on the instrument cluster can be
changed using the control buttons C on the right side of
the steering wheel.
Press Mode buttons
/ to change LCD mode.
Press Move buttons
/ to select item.
Press Select/Reset button
in center to set/reset the item.
C
B
For more detailed information, see the LC D Instrument Cluster Modes section on page 6.
29319_Text.indd 1711/6/15 10:22 AM

OTHER KEY F E AT U R E S
*IF EQUIPPED 44
ABC
DE
FGH
A eServices Guide button B UVO Luxury Services Voice Local Search button C Roadside Assist button D Auto dimming ON/OFF
E Glare detection sensorF HomeLink® button G HomeLink® button
H HomeLink® button
Auto-Dimming Rearview Mirror with \fomeLink®
The Auto-Dimming Rearview Mirror is designed to help reduce glare from a vehicle’s headlights located in
the rear and also connect up to three electronic transmitters in one location. To turn automatic dimming ON
or O F F, press button
D.
\bVO Luxury Services Rearview Mirror Key Functions
A UVO Luxury Services Guide button: Provides information about UVO Luxury Services features within the
vehicle. Press button A and follow the voice prompts to use the eServices Guide.
B UVO Luxury Services Voice Local Search button: Uses Google® to locate points of interest in the
surrounding area. Press button B and follow the voice prompts to use UVO Luxury Services Voice
Local Search.
C Roadside Assist button: Connects to Roadside Assist and provides services including emergency
assistance and vehicle towing. Press button C to connect to Roadside Assist.
REMINDER: Mirror indicator light will illuminate when automatic dimming is ON.
29319_Text.indd 4411/6/15 10:26 AM

OTHER KEY FEATURES
45*IF EQUIPPED
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLE TE OPER ATING INFORMATION AND SAFE T Y WARNINGS.
E Glare detection sensorF HomeLink® button G HomeLink® button
H HomeLink® button
How to Sync Transmitter with HomeLink\f
If programming for the rst time, begin with step 1 (repeating
this step will delete all information).
To program non-rolling and rolling code garage door openers
and other devices:
1. Press and hold the left
F and center G buttons
simultaneously until the indicator light begins to ash (to
reprogram buttons, skip this step)
2. Press and hold the desired button
F, G or H and hold
the button on the transmitter while it is approximately 1 to
3 inches away from the mirror. The HomeLink
® indicator
light will ash rapidly once the frequency signal has been
successfully programmed
To nish programming rolling code garage door openers,
complete these steps:
3. Locate the “learn” or “smart” button on the garage door’s
motor head unit. Press and release the button and complete
step 4 within 30 seconds
4. Firmly press and release the programmed HomeLink
®
button up to three times
Quick Tips
- You can reprogram a single HomeLink® button by
repeating step 2
- Erasing programmed buttons will delete all
trained transmitters
\bperating HomeLink\f:
Press one of the programmed HomeLink
® buttons.
Erasing programmed buttons:
Press and hold the left
F and center H buttons
simultaneously for approximately 20 seconds, and then
release both buttons within 30 seconds.
If your garage door opener was manufactured in 2011
or later, and you are unable to program your vehicle’s
HomeLink
® system, you may need to purchase a
HomeLink® Repeater Kit. For more information, go to
www.HomeLink.com or call (800) 355-3515.
29319_Text.indd 4511/6/15 10:26 AM