2016 KIA CADENZA warning

23
Surround View Monitor (SVM)*
The Surround View Monitor (SVM) system is a parking support system that shows the areas around the front, rear, left, and
right sides of the vehicle via four cameras displayed onto the navigation screen The SVM system will turn on when the SVM
button
A is pressed and the LED is illuminated


Surround View
Monitor Video

To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www. KuTechVideo s.c om/vg13/2016
Front SVM - when in Drive & Neutral: Rear SVM - when in Reverse:
Displays the front side and SVM images
simultaneously on the screen
Displays the front side image on the
screen
Displays the front side and left side
images simultaneously on the screen
Displays the front side and right side
images simultaneously on the screen
Displays the rear view and SVM images
simultaneously on the screen
Displays the rear side image on the
screen
Displays the rear and left side images
simultaneously on the screen
Displays the rear and right side images
simultaneously on the screen
REMINDER: The SVM camera is
equipped with an optical lens to
provide a wider range of vision and
may appear different from the
actual distance
The Surround View Monitor system
is only a supplemental device.
Drivers should not rely solely on the
SVM information when parking and
backing up. Drivers should always
pay attention and directly check the
left/right and rear.

• The Front SVM camera is ON when the ENGINE START/STOP
button is On, the gear shift is in Drive or Neutral and the SVM
button is pressed ON

• Rear SVM: The camera view will automatically display on the
navigation screen when the vehicle is shifted into Reverse
The camera view will turn off when the vehicle is shifted out
of Reverse

• Front SVM: The camera view will display on the navigation
screen in both Drive and Neutral In Drive, the camera
view will continue to display until the vehicle is above
approximately 12 mph The camera view will reappear on
the navigation screen whenever the vehicle drops below
approximately 12 mph
Camera View Modes – To change camera view modes, press the icons shown below on the navigation screen to select the mode


The Front SVM camera will turn off when the gear shift is
moved into Park or Reverse or the SVM button is pressed QUICK TIP
Check yo ur sur roun dings for safety.
(Button located on gear shift)
A
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
CENTER PANEL

25
Climate Control Auto Function
1 Press AUTO to select Full Auto Operation - The Auto setting
automatically controls the airflow modes, fan speeds, air intake
and air conditioning according to the temperature setting selected
2 Set desired Temperature
3 Press DUAL to select Dual Temperature Control Operation
Front windshield
defroster button
Automatic climate control button
REMINDERS:

• Pressing any button during AUTO operation will deactivate the AUTO function and switch to manual mode, except for DUAL
Temperature Control

• When in AUTO mode, Air Flow Mode and Fan Speed do not display on the Climate Control Display

•Warm air may flow in through vents if Recirculated Air button is not pressed ON (LED lit)

• Your Automatic Climate Control system may differ from those in the illustrations See your Owner’s Manual for more details
Air Flow Modes
To select Air Flow Modes, press the MODE button to cycle
through to desired mode:
Face-Level
Bi-Level F lo o r- L evel
Floor/Defrost-Level
CLIMATE
MODE
A/CPASS
AIR BAG
OFFDUAL
Automatic Climate Control
Driver’s/Dual temperature
control buttons Passenger’s temperature
control buttons
Mode selection button
Dual temperature control
selection button
OFF button Recirculated Air ON/OFF button
Fan speed control buttons
Rear window
defroster button Climate information screen
selection button Air conditioning button
Defog Inside Windshield:
1
Set Fan Speed to desired position
2 Set desired Temperature
3 Press the Front Defrost button Defrost Outside Windshield:
1 Set Fan Speed to the highest position
2 Set Temperature to Hot
3 Press the Front Defrost button



•Defrost Mode activates A /C and opens Fresh Air Vent to help dehumidify the air and improve
Defroster performance

•During Auto Operation, the A /C indicator will NOT illuminate The fan speed, air intake, air flow
and air conditioning may automatically be engaged at any time to reach desired temperature
and reduce humidity

•Keep inside glass as clean as possible to reduce window fogging
QUICK TIPS
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
CENTER PANEL

27
Auto-Hold*
Auto-Hold temporarily maintains the vehicle
at a standstill even if the brake pedal is
released Auto-Hold can be turned ON/OFF
using the AUTO HOLD switch
B on the
driver’s panel Before Auto-Hold will operate,
the driver’s door, engine hood and trunk
must be closed, and the driver’s seat belt
must be fastened
The Auto-Hold indicator has four states:
White: Standby - With vehicle at a standstill,
and AUTO HOLD switch
B turned ON, the
indicator will illuminate white While driving
the vehicle (vehicle is not at a standstill), the
Auto-Hold indicator will remain white
Green: Engaged - When coming to a
complete stop by depressing the brake
pedal, the Auto-Hold indicator changes from
white to green
OFF (not illuminated) - The indicator will turn OFF when the AUTO HOLD
switch
B is manually turned OFF or when the EPB is manually turned ON
Yellow: Malfunction - When the indicator is illuminated yellow, there may
be a system malfunction Take your vehicle to a local Kia dealer
Refer to page 4 for location of Instrument Cluster indicators.

Electric Parking Brake*
The Electric Parking Brake (EPB) system utilizes
an electric motor to engage the parking brake
Applying the Parking Brake
Depress the brake pedal and pull up the EPB
switch
A Ensure that the indicator light is
illuminated on the instrument cluster
Releasing the Parking Brake
The EPB will automatically release when the shifter
is placed in Reverse or Drive
To release EPB manually, depress the brake pedal, then press the EPB
switch
A, with the ignition switch in the ON position Ensure that the
indicator light
i s O F F
REMINDERS:

• As a bulb check, the EPB malfunction indicator will illuminate for approximately 3 seconds
when the ignition switch is turned ON

• If the warning light does not illuminate temporarily, or continues to remain lit, take your
vehicle to an authorized Kia dealer and have the system checked

• The EPB should not be operated while the vehicle is moving, unless there is an
emergency situation

• A click or electric brake motor sound may be heard while operating or releasing the EPB,
but these conditions are normal and indicate that the EPB is functioning properly


Electric Parking
Brake Video

To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www. KuTechVideo s.c om/vg13/2016
(Buttons located below Gear Shift)


•When leaving your keys with parking lot attendants or valet, make sure to inform
them how to operate the EPB

•If parked on a steep incline, pull up the EPB switch for more than 3 seconds for a
firmer EPB application

•Pull up and hold EPB switch again to increase brake pressure if parked on a
decline or incline
QUICK TIPS
A
B
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
CENTER PANEL

29


Seat Warmers and
Ventilated Seats Video

To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www. KuTechVideo s.c om/vg13/2016
(Buttons located below Gear Shift)
(Buttons located below Gear Shift)
Seat Warmers / Ventilated Seats*
Seat Warmers
• Press right side of button once for high setting
(3 LEDs lit)

• Press button twice for medium setting (2 LEDs lit)

• Press a third time for low setting (1 LED lit) and
again to turn OFF
Ventilated Seats
• Press left side of button once for high setting
(3 LEDs lit)

• Press twice for medium setting (2 LEDs lit)

• Press a third time for low setting (1 LED lit) and
again to turn OFF
Warming ( Yellow LED)
Ventilating (Blue LED)
Seat Warmers / Ventilated Seats*
Seat Warmers only*

• Press button once for high setting (2 LEDs lit)

• Press button twice for low setting (1 LED lit)

• Press button a third time to turn OFF

•With the seat warmer switch in the ON position, the heating
system in the seat turns OFF or ON automatically depending
on the seat temperature

•System turns OFF when ignition is cycled To turn system ON
again, press the Heated Steering Wheel button
QUICK TIPS
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
CENTER PANEL

31
Front Seat Headrest Adjustment
To adjust headrest forward: Pull headrest forward at an angle
To adjust headrest back: Pull forward at a slight angle to the farthest
position and release Then pull forward to desired position
To raise headrest: Pull headrest up
To lower headrest: Press lock
A, then press the headrest down
Driver Position Memory System*
The integrated system stores into memory the position
of the Driver’s Seat, Outside Rearview Mirrors and the
Steering Wheel
To store positions into memory, first place the Gear
Shift into P (Park) while the ENGINE START/STOP
button is in the ON position Then:
1 Adjust the Driver’s Seat, Outside Mirrors and the
Steering Wheel
2 Press the Memory button
B on the control panel
System will beep once
3 Press one of the memory buttons
C within 5
seconds The system will beep twice when memory
has been stored
M
1
2
(Buttons located on
Driver's Door Panel)
A
B
C
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
SEATING

33
How to Sync Transmitter with HomeLink®
If programming for the first time, begin with Step 1 (repeating this step will
delete all information)
To program non-rolling and rolling code garage door openers and other devices:
1 Press and hold the left
A and center D buttons simultaneously until the
indicator light C begins to flash (to reprogram buttons, skip this step)
2 Press and hold the desired button
A, B or D and hold the button on the
transmitter while it is approximately 1 to 3 inches away from the mirror
The HomeLink
® Indicator light C will flash rapidly once the frequency
signal has been successfully programmed
To finish programming rolling code garage door openers, complete these steps:
1 Locate the “learn” or “smart” button on the garage door’s motor head
unit Press and release the button and complete Step 4 within 30 seconds
2 Firmly press and release the programmed HomeLink
® button up to three times
Operating HomeLink
®:
Press one of the programmed HomeLink
® buttons
Erasing programmed buttons:
Press and hold the left
A and center D buttons simultaneously for
approximately 20 seconds, and then release both buttons within 30 seconds
If your garage door opener was manufactured in 2011 or later, and you’re unable to program
your vehicle’s HomeLink® system, you may need to purchase a HomeLink Repeater Kit. For more
information, go to www.HomeLink.com or call (800) 355-3515.
The HomeLink® / Auto-Dimming Rearview Mirror is designed to reduce
glare from a vehicle’s headlights located in the rear and also connect up
to three electronic transmitters into one location
REMINDER: Mirror indicator light C will illuminate when automatic dimming is ON
HomeLink® with Auto-Dimming Rearview Mirror
A HomeLink® button
B HomeLink® button
C Indicator light
D HomeLink® button
E Glare detection sensor
F Automatic dimming ON/OFF
G Compass control button


•You can reprogram a single HomeLink® button by repeating Step 2
•Erasing programmed buttons will delete all trained transmitters
QUICK TIPS
ABCDEFG
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
OTHER KEY FEATURES

35
Sunvisor
Use the Sunvisor to shield direct light through the front or side
windows Slide the Sunvisor out and adjust as needed
REMINDERS:

•Sunvisor may not shield all direct light

•The Sunvisor may impair visibility if not adjusted properly

• Be aware of seating position when adjusting or swinging Sunvisor around to or from
the front or side windows
Panoramic Sunroof Operation*
The Sunroof and Sunshade operation is controlled through a multidirectional
switch/lever A The ignition needs to be in the ON position to operate the
sunroof/sunshade
Slide the Sunshade and Sunroof:
• Auto Open: Slide lever backward to the farthest position and release
• Auto Close: Slide the lever forward to the farthest position and release
Slide the Sunshade:
• Auto Open: Slide the lever partially backward to the first detent position
• Auto Close: Slide the lever forward to the farthest position
Slide the Sunroof (with Sunshade open):
• Open: Slide the lever backward and release
• Auto Close: Slide the lever forward to the first detent position or pull the
lever downward
Tilt the Sunroof:
• Raise: Push lever upward
• Lower: Pull lever downward
• Auto Close Sunroof and Sunshade: Slide the lever forward to the
farthest position
REMINDER: Sunshade needs to remain OPEN while Sunroof is open and vehicle is moving


To stop the Sunroof/Sunshade at any position, push or pull the Sunroof control lever
in any direction QUICK TIP
A
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
OTHER KEY FEATURES

36
Warning! Check yo ur sur roun dings for safety
Rear-Camera Display
The Rear-Camera Display system is not a safety device It is a supplemental
system that displays the view behind the vehicle through the Navigation
screen while the vehicle is in Reverse
The Rear-Camera Display activates when the:
• ENGINE START/STOP button is in the ON position (Green Light)
• Gear Shift Lever is in the R (Reverse) position
REMINDER: While camera is active, only the volume controls on the audio system can be operated

The Rear-Camera Display is not a substitute for proper and safe backing-up procedures. The
Rear-Camera Display may not display every object behind the vehicle. Always drive safely and use
caution when backing up
Back-Up Warning System
(Rear Parking Assist System)*
The Back-Up Warning System is not a safety device The Back-Up Warning
System is a supplemental system that assists the driver by chiming if any
object is detected within the sensing area to the rear and side of the vehicle
when backing up When the ignition is ON, the system is activated
REMINDERS:

•If the vehicle is moving at speeds over 3 mph, the system may not activate correctly

• When more than two objects are sensed at the same time, the closest one will be
recognized first

• The Back-Up Warning System is not a substitute for proper and safe backing-up procedures
Always drive safely and use caution when backing up The Back-Up Warning System may not
detect every object behind the vehicle
Rear-camera
CADENZA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
OTHER KEY FEATURES