2016 JEEP RENEGADE keyless

VEHICLE SECURITY ALARM..............51
▫To Arm The System....................52
▫To Disarm The System...................53
▫Disabling............................54
DOORS..............................54
▫Manual Door Locks.....................54
▫Central Lock/Unlock....................56
▫Keyless Enter-N-Go....................58
▫Child Locks..........................65
SEATS ...............................66
▫Manual Front Seats.....................67
▫Power Adjustment (Front) — If Equipped.....69
▫Heated Seats — If Equipped...............71▫Rear Seats............................72
HEAD RESTRAINTS.....................78
▫Front Head Restraints...................79
▫Rear Head Restraints....................80
STEERING WHEEL......................81
▫Tilt/Telescoping Steering Column...........81
▫Heated Steering Wheel — If Equipped.......82
MIRRORS.............................83
▫Inside Day/Night Mirror................83
▫Auto Dimming Mirror — If Equipped........84
▫Outside Mirrors.......................85
▫Heated Mirrors — If Equipped............87
28 GETTING TO KNOW YOUR VEHICLE

KEYS
Your vehicle uses either a key start ignition system or
keyless ignition system. The key start ignition system
consists of a Key Fob with a Remote Keyless Entry (RKE)
transmitter and an Ignition Node Module (IGNM). The
keyless ignition system consists of a Key Fob with
Remote Keyless Entry (RKE) transmitter and a Keyless
Ignition Node (KIN).
Key Fob With Remote Control
The Key Fob with Remote Control contains a Remote
Keyless Entry (RKE) transmitter. The RKE system allows
you to lock or unlock the doors and liftgate or activate the
Panic Alarm from distances up to approximately 66 ft (20
m) using a handheld Key Fob with a RKE transmitter.
The RKE transmitter does not need to be pointed at the
vehicle to activate the system.
NOTE:In the ON/RUN position, the LOCK button is
disabled. Only the UNLOCK button is enabled.Vehicles With Keyless Enter-N-Go
Keyless Enter-N-Go Key Fob
4
GETTING TO KNOW YOUR VEHICLE 31

Key Fob With Remote Control And Integrated Vehicle
Key
The Key Fob With Remote Control contains the RKE
transmitter with an integrated vehicle key. To use the
vehicle key, simply push the vehicle key release button.
Keyless Enter-N-Go Key Fob Emergency Key Release
A — Emergency Key Release Button
B — Emergency Key 32 GETTING TO KNOW YOUR VEHICLE

Push and release the UNLOCK button on the RKE
transmitter once to unlock the driver’s door or twice
within five seconds to unlock all doors and the liftgate.
The turn signal lights will flash to acknowledge the
unlock signal. The illuminated entry system will also
turn on.
1st Push Of Key Fob Unlocks
This feature lets you program the system to unlock either
the driver’s door or all doors on the first push of the
UNLOCK button on the RKE transmitter. To change the
current setting, refer to “Uconnect SETTINGS” in “Mul-
timedia” for further information.
NOTE:If the vehicle is equipped with Passive Entry,
refer to “Keyless Enter-N-Go” in “Getting To Know Your
Vehicle” for further information.To Lock The Doors And Liftgate
If equipped, the doors may be locked by inserting the
vehicle key into the exterior driver’s door lock cylinder.
Push and release the LOCK button on the RKE transmit-
ter to lock all doors and liftgate. The turn signal lights
will flash and the horn will chirp to acknowledge the
signal. Settings in radio can change to lights only, chirp
only, or both.
If the vehicle is equipped with Passive Entry, refer to
“Keyless Enter-N-Go” in “Getting To Know Your Ve-
hicle” for further information.
Key Fob With Remote Control And Integrated Vehicle
Key
If one or more doors are open, or the liftgate is open, the
doors will lock. This is signaled by a quick flash of the
turn signals.
34 GETTING TO KNOW YOUR VEHICLE

Vehicles With Keyless Enter-N-Go
If one or more doors are open, or the liftgate is open, the
doors will lock. The doors will unlock again only if the
key is inside the passenger compartment.
NOTE:
•The current setting can be changed within the Elec-
tronic Vehicle Information Center (EVIC) menu or in
the Uconnect Settings so that the system will allow/
inhibit the ability to lock the doors when one or more
of them are open.
•For more information, refer to “Multi-Functional Dis-
play (EVIC)” in “Getting To Know Your Instrument
Panel,” subsection “Electronic Vehicle Information
Center (EVIC)/ Driver Information Display (DID),” or
“Uconnect Settings” in “Multimedia.”Replacing The Battery In The Key Fob With
Remote Control
The recommended replacement battery is one CR2032
battery.
NOTE:
•Perchlorate Material — special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
•Do not touch the battery terminals that are on the back
housing or the printed circuit board.
4
GETTING TO KNOW YOUR VEHICLE 35

Separating Keyless Enter-N-Go Transmitter Case
1. Remove the emergency key by sliding the mechanical
latch on the back of the RKE transmitter sideways
with your thumb. Then, pull the key out with your
other hand.
2. Separating RKE halves requires screw removal (if
equipped) and gently prying the two halves of the
RKE transmitter apart with the emergency key. Make
sure not to damage the seal during removal.
Separating Keyless Enter-N-Go Transmitter Case
A — RKE Transmitter 38 GETTING TO KNOW YOUR VEHICLE

3. Remove the battery by turning the back cover over
(battery facing downward) and tapping it lightly on a
solid surface such as a table or similar surface. Then,
replace the battery.
When replacing the battery, match the + sign on the
battery to the + sign on the inside of the battery clip,
located on the back cover. Avoid touching the new
battery with your fingers. Skin oils may cause battery
deterioration. If you touch a battery, clean it with rubbing
alcohol.
4. To assemble the RKE transmitter case, snap the two
halves together and insert the emergency key.
Keyless Enter-N-Go Battery Replacement
B — Battery
4
GETTING TO KNOW YOUR VEHICLE 39

Programming Additional Transmitters
Programming Key Fobs or RKE transmitters may be
performed at an authorized dealer.
Request For Additional Key Fobs
NOTE:Only Key Fobs that are programmed to the
vehicle electronics can be used to start and operate the
vehicle. Once a Key Fob is programmed to a vehicle, it
cannot be programmed to any other vehicle.
CAUTION!
•Always remove the Key Fobs from the vehicle and
lock all doors when leaving the vehicle unat-
tended.
•For vehicles equipped with Keyless Enter-N-Go,
always remember to place the ignition in the OFF
position.At the time of purchase, the original owner is provided
with a four-digit Personal Identification Number (PIN).
Keep the PIN in a secure location. This number is
required for authorized dealer replacement of Key Fobs.
Duplication of Key Fobs may be performed at an autho-
rized dealer. This procedure consists of programming a
blank Key Fob to the vehicle electronics. A blank Key Fob
is one that has never been programmed.
NOTE:When having the Sentry Key Immobilizer System
serviced, bring all vehicle keys with you to an authorized
dealer.
40 GETTING TO KNOW YOUR VEHICLE