2016 JEEP RENEGADE clock

Clock & Data
By selecting the item,Clock & Datayou can adjust the
clock.
Possible options are:
•Set Time: adjust hours/minutes
•Set Format: adjust the time format12h(12 hours) or
24h(24 hours)
•Set Date: adjust day/month/year
Security
By selecting the item “Security,” you can make the
following adjustments:
•Speed Warning:
Set the vehicle speed limit (km/h or mph), which the
driver is notified through a visual and acoustic signaling
(display of a message and a symbol on the display).When the speed warning is set, the icon should remain
visualized for the same duration time of the pop up. If
the driver exceeded the speed set the icon should remain
for however long the vehicle is over the set speed.
Driver may also turn the Speed Warning “OFF” should
you choose not to use this feature.
•Seat Belt Reminder:
This function is only viewable when the Seat Belt Re-
minder (SBR) system is active.
•Hill Start Assist:
Activation/Deactivation of the Hill Start Assist system.
Safety & Assistance
By selecting the itemSafety & Assistance,you can make
the following adjustments:
•FCW: a selection of operating modes of the system
Forward Collision Warning Plus
230 GETTING TO KNOW YOUR INSTRUMENT CLUSTER

2. Rotate the headlamp bulb socket counterclockwise
then pull outwards.3. Push on the locking tab on the headlamp bulb connec-
tor and remove the bulb and socket.
Headlamp Bulb SocketHeadlamp Bulb Connector
446 IN CASE OF EMERGENCY

4. Install the new headlamp bulb making sure it is
properly locked.5. Install the headlamp bulb and socket; turn it clockwise
making sure it is properly locked.
WARNING!
Carry out the operation of replacing lamps only with
the engine off. Also make sure that the engine is cold,
to avoid the danger of burns.
Headlamp Bulb8
IN CASE OF EMERGENCY 447

3. Remove the electrical connectors. 4.Rotate in a counterclockwise direction (on the left-hand
socket) or in a clockwise direction (on the right-hand
socket) and remove the bulb and bulb socket.
Electrical Connectors
Position Light/Daytime Running Light Assembly
1 — DRL Bulb Socket
2 — Turn Signal Bulb Socket
8
IN CASE OF EMERGENCY 449

5. To replace the bulb gently push bulb and rotate
counterclockwise.6. Insert the new bulb by pushing on it and turning it
clockwise. Make sure the bulb is correctly locked in
place.
7. Install the bulb and sockets and rotate them clockwise
(right side) and clockwise (left side), making sure that
it is properly locked.
8. Reconnect the electrical connectors.
9. Reinstall the access door.
Bulb and Socket Assembly
1 — Bulb
2 — Rotate Bulb 450 IN CASE OF EMERGENCY

3. By pushing the electrical connector tab remove the
electrical connector.4. Rotate the bulb counterclockwise, and then replace the
bulb.
5. Insert the new bulb in the socket, making sure the bulb
is locked into place.
6. Reconnect the electrical connector.
7. Reinstall the access door.
Fog Light Assembly
1 — Bulb Socket
2 — Electrical Connector
3 — Bulb 452 IN CASE OF EMERGENCY

3. Remove the electrical connector by pushing the tab
then disconnect the electrical connector.4. Rotate counterclockwise to release the bulb socket
from the lamp assembly, and remove it.
Electrical ConnectorBulb Socket
454 IN CASE OF EMERGENCY

5. Remove the bulb from the socket
6. Insert the new bulb in the socket.7. Reinstall the bulb and socket into the lamp assembly
by turning it clockwise, making sure it is locked into
place.
8. Reconnect the electrical connector.
9. Reinstall the lamp assembly on the car, making sure it
is locked into place.
Side Indicators on External Rear View Mirrors – (If
Equipped)
CAUTION!
The procedure is described as a guideline. For the
replacement of the lamp it is recommended that you
contact your authorized dealer.
Bulb8
IN CASE OF EMERGENCY 455