2016 JEEP COMPASS radio

Headlights On With Wipers (Available With
Automatic Headlights Only)
When this feature is active, the headlights will turn on
approximately 10 seconds after the wipers are turned on
if the headlight switch is placed in the AUTO position. In
addition, the headlights will turn off when the wipers are
turned off if they were turned on by this feature.
NOTE:The Headlights On with Wipers feature can be
turned on or off using the Electronic Vehicle Information
Center (EVIC). Refer to “Electronic Vehicle Information
Center (EVIC)” in “Understanding Your Instrument
Panel” for further information.
Instrument Panel Dimming
Rotate the center portion of the lever to the extreme
bottom position to fully dim the instrument panel lights
and prevent the interior lights from illuminating when a
door is opened.
Rotate the center portion of the lever up to increase the
brightness of the instrument panel lights when the park-
ing lights or headlights are on.
Rotate the center portion of the lever upward to the next
detent position to brighten the odometer and radio when
the parking lights or headlights are on.
Rotate the center portion of the lever upward to the last
detent to turn on the interior lighting.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Before You Begin Programming HomeLink
Be sure that your vehicle is parked outside of the garage
before you begin programming.
For more efficient programming and accurate transmis-
sion of the radio-frequency signal it is recommended that
a new battery be placed in the hand-held transmitter of
the device that is being programmed to the HomeLink
system.
To erase the channels place the ignition in the ON/RUN
position and push and hold the two outside HomeLink
buttons (I and III) for up 20 seconds or until the red
indicator flashes.NOTE:
•
Erasing all channels should only be performed when
programming HomeLink for the first time. Do not
erase channels when programming additional buttons.
• If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.
Programming A Rolling Code
For programming garage door openers that were manu-
factured after 1995. These garage door openers can be
identified by the “LEARN” or “TRAIN” button located
where the hanging antenna is attached to the garage door
opener. It is NOT the button that is normally used to
open and close the door. The name and color of the
button may vary by manufacturer.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183

Canadian/Gate Operator Programming
For programming transmitters in Canada/United States
that require the transmitter signals to “time-out” after
several seconds of transmission.
Canadian radio frequency laws require transmitter sig-
nals to time-out (or quit) after several seconds of trans-
mission – which may not be long enough for HomeLink
to pick up the signal during programming. Similar to this
Canadian law, some U.S. gate operators are designed to
time-out in the same manner.
It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the garage
door or gate motor.
1. Cycle the ignition to the ON/RUN position.2. Place the hand-held transmitter 1 to 3 inches (3 to
8 cm) away from the HomeLink button you wish to
program while keeping the HomeLink indicator light
in view.
3. Continue to push and hold the HomeLink button, while you push and release (“cycle”) your hand-held
transmitter every two seconds until HomeLink has
successfully accepted the frequency signal. The indi-
cator light will flash slowly and then rapidly when
fully trained.
4. Watch for the HomeLink indicator to change flash rates. When it changes, it is programmed. It may take
up to 30 seconds or longer in rare cases. The garage
door may open and close while you are programming.
5. Push and hold the programmed HomeLink button and observe the indicator light.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187

approximately eight turns, then move the crossbar to the
desired position, keeping the crossbars perpendicular to
the luggage rack side rails. Once the crossbar is in one of
the seven detent positions, retighten the thumb screws to
lock the crossbar into position.
NOTE:
•To help control wind noise when the crossbars are not
in use, place the front crossbar in the first detent from
the front of the vehicle and the rear crossbar in the
second detent from the rear of the vehicle.
• If the rear crossbar (or any metallic object) is placed
over the satellite radio antenna (if equipped), you may
experience interruption of satellite radio reception. For
improved satellite radio reception, place the rear cross-
bar in the second detent from the rear of the vehicle
when not in use.CAUTION!
• To prevent damage to the roof of your vehicle, DO
NOT carry any loads on the luggage rack without
crossbars installed. The load should be secured and
placed on top of the crossbars, not directly on the
roof. If it is necessary to place the load on the roof,
place a blanket or some other protection between
the load and the roof surface.
• To avoid damage to the luggage rack and vehicle,
do not exceed the maximum luggage rack load
capacity of 150 lb (68 kg). Always distribute heavy
loads as evenly as possible and secure the load
appropriately.
• Long loads which extend over the windshield, such
as wood panels or surfboards, or loads with large
frontal area should be secured to both the front and
rear of the vehicle.
(Continued)
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

▫Display Units Of Measure In .............255
 Personal Settings (Customer-Programmable
Features) ............................ .255
▫ Language .......................... .255
▫ Auto Lock Doors ..................... .256
▫ Auto Unlock On Exit ...................256
▫ RKE Unlock ........................ .256
▫ Flash Lamps With Lock .................256
▫ Sound Horn With Lock .................257
▫ Headlamp Off Delay ...................257
▫ Headlamps with Wipers (Available with Auto
Headlights Only) ..................... .257
▫ Key Off Power Delay ...................257
▫ Illuminated Approach ..................258 ▫
Hill Start Assist (HSA) — If Equipped .......258
▫ Display Units In ..................... .258
▫ Automatic Compass Calibration ...........258
▫ Manual Compass Calibration .............259
▫ Compass Variance ....................259
 UCONNECT 230 – AM/FM STEREO RADIO AND
6–DISC CD/DVD CHANGER (MP3/WMA AUX
JACK) ............................. .261
▫ Operating Instructions — Radio Mode .......261
▫ Operation Instructions — DISC Mode For CD And
MP3/WMA Audio Play, DVD – Video .......270
▫ LIST Button — DISC Mode For MP3/WMA
Play .............................. .275
▫ INFO Button — DISC Mode For MP3/WMA
Play .............................. .275
214 UNDERSTANDING YOUR INSTRUMENT PANEL

▫Uconnect (Satellite Radio) — If Equipped . . . .277
 UCONNECT 430/430N CD/DVD/HDD/NAV — IF
EQUIPPED .......................... .282
▫ Operating Instructions (Voice Command System)
— If Equipped ...................... .282
▫ Operating Instructions (Uconnect Phone) — If
Equipped .......................... .282
 UCONNECT 130 ...................... .282
▫ Operating Instructions — Radio Mode ......282
▫ Operation Instructions — CD MODE For CD And
MP3 Audio Play ..................... .286
▫ Notes On Playing MP3 Files .............288
▫ Operation Instructions — Auxiliary Mode . . . .291
 UCONNECT 130 WITH SATELLITE RADIO . . .292 ▫
Operating Instructions — Radio Mode ......292
▫ Operation Instructions — CD MODE For CD And
MP3 Audio Play ..................... .298
▫ Notes On Playing MP3 Files .............300
▫ LIST Button — CD Mode For MP3 Play ......303
▫ INFO Button — CD Mode For MP3 Play .....303
▫ Uconnect (Satellite Radio) — If Equipped . . . .304
 iPod/USB/MP3 CONTROL — IF EQUIPPED . . .309
▫ Connecting The iPod Or External USB
Device ............................ .309
▫ Using This Feature .....................310
▫ Controlling The iPod Or External USB Device
Using Radio Buttons ...................310
▫ Play Mode ..........................311
4
UNDERSTANDING YOUR INSTRUMENT PANEL 215

▫List Or Browse Mode ...................312
▫ Bluetooth Streaming Audio (BTSA) .........314
 STEERING WHEEL AUDIO CONTROLS ......315
▫ Radio Operation ..................... .316
▫ CD Player .......................... .317
 CD/DVD DISC MAINTENANCE ...........317
RADIO OPERATION AND MOBILE DEVICES . .318
 CLIMATE CONTROLS ...................318
▫ Manual Heating And Air Conditioning ......318
▫ Automatic Temperature Control (ATC) — If
Equipped .......................... .323
▫ Operating Tips ...................... .329
216 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT PANEL FEATURES
1 — Air Outlet5 — Storage Bin9 — Heated Seat Switch – If Equipped
2 — Demisters 6 — Glove Compartment10 — Hazard Warning Flasher
3 — Instrument Cluster 7 — Climate Controls11 — ESC OFF Switch – If Equipped
4 — Radio 8 — Power Outlet12 — Heated Seat Switch – If Equipped
4
UNDERSTANDING YOUR INSTRUMENT PANEL 217