2016 HYUNDAI I20 headlight bulb

)'
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
To flash the high beam headlights,
pull the lever towards you, then
release the lever. The high beams
will remain ON as long as you hold
the lever towards you.
TT urn signals and lane change sig-
nalsTo signal a turn, push down on the
lever for a right turn or up for a left
turn in position (A). To signal a lane
change, move the turn signal lever
slightly and hold it in position (B). The
lever will return to the OFF position
when released or when the turn is
completed.
If an indicator stays on and does not flash or if it flashes abnormally, one ofthe turn signal bulbs may be burned
out and will require replacement.
One-touch lane change function
(if equipped)To activate an One-Touch Lane
Change function, move the turn sig-
nal lever slightly and then release it.
The lane change signals will blink 3,
5 or 7 times.
You can activate/deactivate the One
Touch Turn Signal function or choose
the number of blinking (3, 5, or 7)
from the User Settings Mode on the
LCD display.For more details, refer to "LCD
Display" in this chapter.
If the turn signal indicator stays on
and does not flash, or if it flashes
abnormally, a bulb may be burned
out or have a poor electrical connec-
tion in the circuit. The bulb may
require replacement.NOTICE
OLF044088R
OLF044091R

1.$#,204/3424-3!#Consult an authorized HYUNDAI
dealer to replace most vehicle light
bulbs. It is difficult to replace vehicle
light bulbs because other parts of the
vehicle must be removed before you
can get to the bulb. This is especially
true for removing the headlight
assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to
the vehicle.
Information
After heavy driving, rain or washing
headlight and taillight lenses could
appear frosty. This condition is caused
by the temperature difference
between the lamp inside and outside.
This is similar to the condensation on
your windows inside your vehicle dur-
ing the rain and doesn’t indicate a
problem with your vehicle. If the
water leaks into the lamp bulb circuit-
ry, we recommend that the system be
checked by an authorized HYUNDAI
dealer.
Be sure to replace the burned-out
bulb with one of the same wattage
rating. Otherwise, it may cause dam -
age to the fuse or electric wiring sys-
tem.
i
Prior to replacing a light, depress
the foot brake, move the shift lever
into the P (Park, for Continuo usly
Variable Transaxle vehicle) or
neutral (for Manual Transaxle
vehicle), apply the parking brake,
plac e the ignition switch in the
LOCK/OFF position, and take the
key with you when leaving the
vehicle to av oid sudden move-
ment of the vehicle and to prevent
possible electric shock.
Be aware the bulbs may be h ot
and may burn your fingers.
WARNING

1.$$
,204/3424-3
HHeadlight, Parking (Position)
Light, Turn signal Light, Low
Beam Assist-Static Light, Fog
Light and Daytime Running Light
bulb replacement(1) Headlight (Low/High) *
1
(2) Parking (Position) Light
(3) Front Turn signal Light
(4) Daytime Running Light
(if equipped)
(5) Front Fog Light (if equipped)
*1: MFR (Multi Focus Reflector) Headlight (1) Headlight (Low/High) *
2
(2) Low Beam Assist-Static Light
(3) Front Turn Signal Light
(4) Position Light/ Daytime Running Light (DRL)
(5) Front Fog Light (if equipped)
*2: Bi-Function Projection Headlight (1) Headlight (Low/High) *
1
(2) Parking (Position) Light
(3) Front Turn signal Light
(4) Front Fog Light (if equipped)
*1: MFR (Multi Focus Reflector)
Headlight
OIB077068
■ 5 Door
• Type A
OIB077069
■5 Door
• Type B
OIB077070
■Cross
• Type A

1.$',204/3424-3
(1) Headlight (Low/High) *
2
(2) Low Beam Assist-Static Light
(3) Front Turn Signal Light
(4) Position Light/ Daytime Running Light (DRL)
(5) Front Fog Light (if equipped)
*2: Bi-Function Projection Headlight
II nformation
If the headlight aiming adjustment
is necessary after the headlight
assembly is reinstalled, consult an
authorized HYUNDAI dealer.
The Fog Light aiming adjustment can be done by removing UNDER
COVER. Consult an authorised
HYUNDAI dealer.i(Continued)•
Always handle them carefully,
and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact w ith liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burs t when lit. A
bulb should be operated only
when installed in a headlight.
•
If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•
Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.
Halogen bulbs•
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
(Continued)
WARNING
OLMB073042L
OIB077060
■Cross
• Type B

1.$1
,204/3424-3
HHeadlight (Low/High)1. Open the hood.
2. Remove the headlight bulb cover
by turning it counterclockwise.
3. Disconnect the headlight bulb socket-connector. 4. Unsnap the headlight bulb retain-
ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head- light assembly.
6. Install a new headlight bulb and snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
- Bi-Function projection
headlight
This headlight is bi-function type that
switches the low beam to high or the
high beam to low using solenoid sys-
tem. So, the moving sound may be
heard when the headlight switches the
low beam to high or the high beam to
low and it does not indicate malfunc-
tion of the headlight.
Turn signal light1. Remove the turn signal light bulb cover by turning it counterclock-
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
i
OIB074048
Turn signal light
Parking
(Position) light
Headlight
■ MFR (Multi Focus Reflector) Headlight
OIB075061
Turn signal light
Headlight
■Bi-Function Projection Headlight

# &$$&)
!
10
+'-"-'($-),%**),%#+&*-,")&#($-),
Light BulbBulb type Wattage
Front Headlight (High/Low)
Type A
H460/55
Type B HB360
Position Light Type A
W5W5
Type B LEDLED
Static Bending Light (SBL) Type BH755
Turn signal Light PY2\fW2\f
Fog Light * 88\f27
Daytime Running Light (DRL) * LEDLED
Side Repeater Light (Outside Mirror) WY5W or LED 5 or LED
Rear Tail Light
P2\f/5W5
Tail and Stop Light P2\f/5W2\f/5
Turn Signal Light PY2\fW2\f
Back Up Light 5 Door
W\f6W\f6
Cross PY2\fW2\f
High Mounted Stop Lamp * W5W5
License Plate Lamps W5W5
Interior Map Lamps
FESTOON8
Room Lamp FESTOON8
Luggage Room Lamp * FESTOON\f0
* : If equipped
Type A : MFR (Multi Focus Reflector) Headlamp
Type B : Bi\bFunction Projection Headlamp