2016 HYUNDAI I20 maintenance

1.%(
,204/3424-3
VVapor hose and fuel filler capThe vapor hose and fuel filler cap
should be inspected at those inter-
vals specified in the maintenance
schedule. Make sure that a new
vapor hose or fuel filler cap is cor-
rectly replaced.
Vacuum crankcase ventilation
hoses (if equipped)Inspect the surface of hoses for evi-
dence of heat and/or mechanical
damage. Hard and brittle rubber,
cracking, tears, cuts, abrasions, and
excessive swelling indicate deterio-
ration. Particular attention should be
paid to examine those hose surfaces
nearest to high heat sources, such
as the exhaust manifold.
Inspect the hose routing to assure
that the hoses do not come in con-
tact with any heat source, sharp
edges or moving component which
might cause heat damage or
mechanical wear. Inspect all hose
connections, such as clamps and
couplings, to make sure they are
secure, and that no leaks are pres-
ent. Hoses should be replaced
immediately if there is any evidence
of deterioration or damage.
Air cleaner filterWe recommend that the air cleaner
filter be replaced by an authorized
HYUNDAI dealer.Spark plugsMake sure to install new spark plugs
of the correct heat range.Do not disconnect and inspect
spark plugs when the engine is
hot. You may burn yourself.
WARNING

1.%#,204/3424-3CCooling systemCheck cooling system components,
such as radiator, coolant reservoir,
hoses and connections for leakage
and damage. Replace any damaged
parts.CoolantThe coolant should be changed at
the intervals specified in the mainte-
nance schedule.Manual transaxle fluid
(if equipped)Inspect the manual transaxle fluid
according to the maintenance sched-
ule.
Continuously Variable Transaxle
fluid (if equipped)Continuously Variable Transaxle fluid
should not be checked under normal
usage conditions.
But, the Continuously Variable
Transaxle fluid should be changed
under severe usage conditions. We
recommend that the Continuously
Variable Transaxle fluid changed by
an authorized HYUNDAI dealer
according to the maintenance sched-
ule. (Refer to “Maintenance Under
Severe Usage Conditions” in this
chapter. )
Information
Continuously Variable Transaxle fluid
color is basically light amber.
As the vehicle is driven, the
Continuously Variable Transaxle fluid
will begin to look darker.
It is normal condition and you should
not judge the need to replace the fluid
based upon the changed color.
The use of non-specified fluid (even
marked as compatible with genuine)
could result in shift quality d eteriora-
tion and vibrations, eventually, the
transaxle failure.
Use only specified Continuously
Variabl e Transaxle fluid. (Refer to
"Recommended lubricants and
capacities" in chapter 8.)Brake hoses and linesVisually check for proper installation,
chafing, cracks, deterioration and
any leakage. Replace any deteriorat-
ed or damaged parts immediately.Brake fluidCheck brake fluid level in the brake
fluid reservoir. The level should be
between "MIN" (Minimum) and
"MAX" (Maximum) marks on the side
of the reservoir. Use only hydraulic
brake fluid conforming to DOT 3 or
DOT 4 specification.NOTICE
i

1.+1
,204/3424-3
!#$ "$#Filter replacement You can clean the filter when inspect-
ing the air cleaner element.
Clean the filter by using compressed
air.
1. Loosen the air cleaner cover attaching clips and open the cover. 2. Remove the used filter and wipe
the inside of the air cleaner hous-
ing carefully not to remain dusts in
the cover housing.
3. Place new filter with clean hands and ensure the rubber gasket is
not taken off.
4. Lock the cover with attaching clips.
Replace the filter according to the
Maintenance Schedule.
If the vehicle is operated in extreme- ly dusty or sandy areas, replace theelement more often than the usualrecommended intervals. (Refer to“Maintenance under severe usageconditions” in this chapter.)
• Do not drive with the filter removed; this will result in exces-
sive engine wear.
• When replacing th e air cleaner fil-
ter, be careful that dust or dirt does
not enter the air intake, or damage
may result .
Keep the new filter clean of any
contamination while replacing.
• We recommend that you use parts for re placement from an author-
ized HYUNDAI dealer.NOTICE
OIB074017
OIB074018
Don’t clean the used filter. It can
cause contaminations on the
clean side of filter to result in
engine wear or sensors’ failure.
CAUTION

1.),204/3424-3! $#"# !#!$#
!#$!$Filter inspectionIf the vehicle is operated in the
severely air-polluted cities or on
dusty rough roads for a long period,
it should be inspected more fre-
quently and cleaned earlier. When
you, the owner, clean the climate
control air filter, clean it performing
the following procedure, and be care-
ful to avoid damaging other compo-
nents.
Replace the filter according to the
maintenance Schedule.
Filter replacement1. Open the glove box.2. Push in both sides of the glove box
as shown. This will ensure that the
glove box stopper pins will get
released from its holding location
allowing the glove box to hang.
OIB074022
OIB044021

1.)$
,204/3424-3
IIf you connect unauthorized elec-
tronic devices to the battery, the bat-
tery may be discharged. Never use
unauthorized devices.
Battery capacity label ❈ The actual battery label in the vehicle
may differ from the illustration.1. CMF60L-BCI : The HYUNDAI model name of battery
2. 12V : The nominal voltage
3. 60Ah(20HR) : The nominal capac- ity (in Ampere hours)
4. 92RC : The nominal reserve capacity (in min.)
5. 550CCA : The cold-test current in amperes by SAE
6. 440A : The cold-test current in amperes by EN
Battery rechargingYour vehicle has a maintenance-free,
calcium-based battery.
• If the battery becomes dischargedin a short time (because, for exam-
ple, the headlights or interior lights
were left on while the vehicle was
not in use), recharge it by slow
charging (trickle) for 10 hours.
• If the battery gradually discharges because of high electric load while
the vehicle is being used, recharge
it at 20-30A for two hours.
NOTICE
OJD072039
■
Example
(Continued)•
Never attempt to recharge the
battery when the battery cables
are connected.
•
The electrical ignition system
works with high voltage. Never
touch these components with
the engine run ning or the igni-
tion switched on.
Failure to follow the above warn-
ings can result in serious bodily
injury or death.

1.)',204/3424-3
RReset itemsItems should be reset after the bat-
tery has been discharged or the bat-
tery has been disconnected.
• Auto up/down window
(See chapter 3)
• Climate control system (See chapter 3)
• Audio (See chapter 3)Battery replacementReplacing a Battery required precau-
tionary measures.
We recommend that you consult an
authorized HYUNDAI dealer.
•
Disconnect the battery charger
in the following order.
1.Turn off the battery charger main switch.
2.Unho ok the negative clamp from
the negative battery terminal.
3.Unhook the positive clamp from the positive battery terminal.
•
Before performing maintenance
or recharging the battery, turn
off all accessories and stop the
engine.
•
The negative battery cable must
be removed first and installed
last when the battery is discon-
nected.
WARNING
Recharging battery
When recharging the battery,
observe the following precautions:•
The battery must be removed
from the vehicle and placed in
an area with good ventilation.
•
Do not allow cigarettes, sparks,
or flame near the battery.
•
Watch the battery during charg-
ing, and stop or reduce the
charging rate if the battery cells
begin gas sing (boiling) violently
or if the temperature of the elec-
trolyte of any cell exceeds 49°C
(120°F).
•
Wear eye protection when
checking the battery during
charging.
(Continued)
(Continued)
WARNING

1.)1
,204/3424-3
!$# "#$$#Tire care For proper maintenance, safety, and
maximum fuel economy, you must
always maintain recommended tire
inflation pressures and stay within
the load limits and weight distribution
recommended for your vehicle. Recommended cold tire inflation
pressures All tire pressures (including the
spare) should be checked when the
tires are cold. “Cold Tires” means the
vehicle has not been driven for at
least three hours or driven less than
1.6 km (one mile).
Recommended pressures must be
maintained for the best ride, top vehi-
cle handling, and minimum tire wear.
For recommended inflation pressure,
refer to “Tire and wheels” in chapter
8. All specifications (sizes and pres-
sures) can be found on a label
attached to the vehicle.
OIB074055
Tire underinflation
Severe underinflation (70 kPa (10
psi) or more) can lead to severe
heat build-up, ca using blowouts,
tread separation and other tire fail-
ures that can result in the loss of
vehicle contro l leading to severe
injury or death. This risk is much
higher on hot days and when driv-
ing for long pe riods at high
speeds.
WARNING

1.((
,204/3424-3
WWheel replacement When replacing the metal wheels for
any reason, make sure the new
wheels are equivalent to the original
factory units in diameter, rim width
and offset.
Tire tractionTire traction can be reduced if you
drive on worn tires, tires that are
improperly inflated or on slippery
road surfaces. Tires should be
replaced when tread wear indicators
appear. Slow down whenever there
is rain, snow or ice on the road, to
reduce the possibility of losing con-
trol of the vehicle.Tire maintenance In addition to proper inflation, correct
wheel alignment helps decrease tire
wear. If you find a tire worn unevenly,
have your dealer check the wheel
alignment.
When you have new tires installed,
make sure they are balanced. This
will increase vehicle ride comfort and
tire life. Additionally, a tire should
always be rebalanced if it is removed
from the wheel.
Tire sidewall labelingThis information identifies and
describes the fundamental charac-
teristics of the tire and also provides
the tire identification number (TIN)
for safety standard certification. The
TIN can be used to identify the tire in
case of a recall.1. Manufacturer or brand nameManufacturer or Brand name is
shown.
A wheel that is not the correct size
may adversely affect wheel and
bearing life, braking and stopping
a bilities, handling characteristics,
ground clearance, body-to-tire
clearance, snow chain clearance,
spee dometer and odometer cali-
bration, headlight aim and bumper
height.
WARNING
I030B04JM
1
1
2
34
5,6
7