2016 Hyundai Equus steering

Steering wheel audio control
Audio control buttons may be provid-
ed on the steering wheel.
Do not simultaneously operate
several audio remote control but-
tons.
VOLUME (VOL + / - ) (1)
• Press the VOL + button to increasethe volume.
Press the VOL - button to decrease the volume.
SEEK/PRESET ( / ) (2)
When one of the < / > buttons is
pressed for 0.8 seconds or longer, it
will function as follows in each mode.
RADIO mode
Those will function as the AUTO
SEEK buttons. It will SEEK (or tune
in) a radio station until you release
the button.
MEDIA mode
Those will function as the FF/REW
button. When one of the < / > buttons is
pressed shorter than 0.8 seconds, it
will function as follows in each mode.
RADIO mode
Those will function as the PRESET
STATION buttons.
MEDIA mode
Those will function as the TRACK
UP/DOWN buttons.
MODE (3)
Press the MODE button to select
among the Radio, disc, or AUX
modes.
MUTE (4)
Press the MUTE button to cancel
the sound.
Press the MUTE button again to activate the sound.
Information
Detailed information is described in a
separate-volume supplement to this
Owner's Manual.
i
NOTICE
4-3
Multimedia system04
OVI045155N

START
To start the engine, depress the
brake pedal and press the Engine
Start/Stop Button with the shift gear
in P(Park) or N(Neutral).
For your safety, start the engine with
the shift gear in P(Park).
Information
• If you press the Engine Start/Stopbutton without depressing the brake
pedal, the engine does not start.
When the Engine Start/Stop button
is pressed, it changes as follows:
OFF → →
ACC →
→
ON →
→
OFF
• If you leave the Engine Start/Stop Button in the ACC or the ON posi-
tion for a long time, the battery will
be discharged.
i
5-8
Driving your vehicle
Never press the Engine Start/Stop button while the
vehicle is in motion except in
an emergency situation. This
would turn the engine OFF,
resulting in loss of power
assist for the steering wheel
and brake. This may lead to
loss of directional control and
braking function, which could
cause an accident.
(Continued)
(Continued)
Before leaving the driver’sseat, always make sure the
shift gear is engaged in P
(Park), fully set the parking
brake and turn the engine
OFF. Unexpected and sudden
vehicle movement may occur
if these precautions are not
taken.
Never touch the Engine Start/Stop button, or any other
controls on the steering wheel
while the vehicle is in motion.
Reaching out for those con-
trols with your hand or arm
may cause a loss of vehicle
control, an accident, serious
bodily injury or death.
Do not place any loose objects around the driver’s
seat, as they may toss about
while driving, interfering with
the driver's pedal operation
and leading to an accident.
WARNING

Moving up a steep grade from astanding start
To drive up on a steep slope,
depress the brake pedal, move the
shift gear to D (Drive), and release
the parking brake. Gradually depress
the accelerator while releasing the
service brakes.
When accelerating on a steep
slope, the vehicle may have a ten-
dency to slide backwards. Shifting
to the 2nd gear (Second Gear) will
help prevent the vehicle from slid-
ing backwards.
5-16
Driving your vehicle
Always buckle up! In a colli- sion, an unbelted occupant is
more likely to be seriously
injured or killed than a proper-
ly belted occupant.
Avoid high speeds when cor- nering or turning.
Do not make quick wheel steering, such as sharp lane
changes or fast, sharp turns.
The risk of rollover is greatly increased when you lose con-
trol of your vehicle at a high
speed.
Loss of control often occurs, when two or more wheels are
swerved out of the roadway
and are overly steered to
reenter the roadway.
In the event your vehicle is swerved out of the roadway,
do not make a sharp steering.
Instead, slow down the vehi-
cle before reentering into the
lanes.
Never exceed posted speed limits.
WARNING
When your vehicle is stuck in
snow, mud, sand and others,
you may rock the vehicle by
moving it forward and back-
wards. Do not attempt this pro-
cedure when there are people
or objects near the vehicle.
During the rocking operation,
the vehicle may suddenly move
forwards or backwards as it
becomes unstuck, causing
injury or damage to nearby peo-
ple or objects.
WARNING

Power brakes
Your vehicle is equipped with the
power-assisted brakes that automat-
ically adjust themselves in a normal
driving condition.
In the event that the power-assisted
brakes lose power because of a
stalled engine or some other rea-
sons, you can still stop your vehicle
by depressing the brake pedal hard-
er than you do in normal driving. A
braking distance, however, will be
longer.
When the engine is OFF, the reserve
brake power becomes partially
depleted each time the brake pedal
is depressed. Do not repeatedly
depress the brake pedal when the
power brake is automatically set.
Pump the brake pedal only when
necessary to maintain the steering
control on slippery surfaces.
B BR
RA
A K
KE
E
S
S Y
Y S
ST
T E
EM
M

5-17
Driving your vehicle05
- Brakes
Do not put your foot on the
brake pedal while driving. This
may abnormally increase the
brake temperatures, wear
down the brake lining/pad,
and increase the braking dis-
tances.
When driving down on a long or steep slope, shift to a lower
gear and avoid depressing the
brakes in a continuous man-
ner. Depressing brakes in a
continuous manner may over-
heat the brakes, resulting in a
temporary loss of braking per-
formance.
(Continued)
(Continued)
Wet brakes may impair thevehicle’s ability to safely slow
down. The vehicle may also be
swerved to one side when the
wet brakes are depressed.
Lightly depress the brakes to
verify whether the brakes are
wet and show the above
symptom. Always test your
brakes in this fashion after
driving through deep water.
To dry the wet brakes, lightly
depress the brakes, while
maintaining a safe driving
speed until the brake perform-
ance returns to normal.
Always confirm the positions of the brake and accelerator,
before driving. If you do not
so, you may be confused and
depress the accelerator
instead of the brake pedal. It
may cause a serious accident.
WARNING

Check the brake warning light by
turning the ignition switch ON (do not
start the engine). This light illumi-
nates when the parking brake is
depressed with the ignition switch in
the START or ON position.
Before driving, make sure that the
parking brake is fully released and
the brake warning light goes OFF.
When the brake warning light
remains ON even after releasing the
parking brake while engine is run-
ning, there may be a malfunction in
the brake system. Immediate atten-
tion is necessary.
If at all possible, immediately stop
driving. If not, use extreme caution
and continuously drive the vehicle
until you can reach a safe location.
Electronic stability control
(ESC)
The ESC system is to stabilize the
vehicle in cornering maneuvers. The
ESC monitors your steering and driv-
ing. The ESC applies to a brake of an
individual wheel and engage in the
engine management system in order
to stabilize the vehicle.
5-28
Driving your vehicle
OVI055021N
Never drive too fast or quickly
when cornering. The ESC can-
not prevent accidents under
this condition. Excessively high
speed in turning, abrupt driving
maneuvers, and hydroplaning
on a wet surface may result in
serious accidents. Only safe
and attentive driving can pre-
vent accidents, avoiding trac-
tion loss of a vehicle. Even with
the ESC equipment of your
vehicle, always follow all the
driving precautions, including
driving at a safe speed.
WARNING
WKH-002

The ESC system is an electronic
system to help the driver maintain
vehicle control in adverse conditions.
It is not a substitute for safe driving
practices. Various factors, including
speed, road conditions and driver's
steering maneuver, affect the ESC
performance in preventing a loss of
control. It is still driver's responsibility
to drive and corner at a proper speed
and to keep a safe distance. When
depressing the brake under condi-
tions, which may lock the wheels,
you may hear a snapping sound and
feel like that from the brake pedal.
This is normal and indicates your
ESC actively operates.
Information
A clicking sound may be heard from
the engine compartment, when the
engine is started and the vehicle
begins to move. This is normal, indi-
cating that the ESC actively operates.
ESC operation
ESC ON condition
When the Engine Start/Stop button
is turned ON, the ESC and the ESC
OFF indicator lights illuminate for
approximately 3 seconds and goes
off, then the ESC is turned on.
When operating
When the ESC operates,
the ESC indicator will flash.
operates, you can feel a
slight pulsation from the
vehicle. This is because of
the brake control, and
does not indicate a prob-
lem.
mud or driving on a slip-
pery road, the engine rpm
may not be increased
even with the accelerator
deeply depressed. This is
to maintain the stability
and traction and does not
indicate a problem.
i
5-29
Driving your vehicle05

SPORT mode
The SPORT mode focuses on the
driving dynamics by automatically
adjusting the steering wheel, sus-
pension (where the ECS is
equipped), engine and transmission
system.is selected by pressing
the DRIVE MODE but-
ton, the SPORT indica-
tor will illuminate.
Even after the SPORT mode is acti- vated, restarting of the engine
resets the DRIVE mode to be in the
NORMAL mode. Thus, when nec-
essary, re-select the SPORT mode.
ed:
- The RPM(revolutions per minutes) level is maintained over a certain
length of time, even when the
accelerator is released.
- Up-shifting timing is delayed, when accelerating.
Information
In the Sport mode, the fuel efficiency
may decrease.
Information
When a Driving Mode theme is select-
ed in the User Settings Mode of the
LCD display (if equipped), the
SPORT and SNOW indicators will not
illuminate on the instrument cluster.
SNOW mode (if equipped)
Snow mode helps the driver to more
effectively drive a vehicle on slippery
roads, such as snowy or muddy
roads.
is selected by pressing
the DRIVE MODE but-
ton, the SNOW indicator
will illuminate.
i
i
5-35
Driving your vehicle05

Information
During the normal operation of the
Smart Cruise Control, with the SET
switch activated or reactivated after
applying brakes, the Smart Cruise
Control will energize after approxi-
mately 3 seconds. This delay is nor-
mal.
Smart Cruise Control speed
To set the cruising speed:
1. Press the CRUISE (ONton on the steering wheel to turn
the system ON. The CRUISE indi-
cator on the instrument cluster will
illuminate.
2. Accelerate to a desired speed. (180 km/h) : when there is no
vehicle in front
km/h) : when there is a vehicle in
front 3.Press the SET- switch, and release
it at the desired speed. The SET
indicator, the set speed and the
vehicle-to-vehicle distance on the
LCD display will illuminate.
Release the accelerator. The set
speed will automatically be main-
tained.
When there is a vehicle in front, thespeed may decrease to maintain asafe distance.
On a steep slope, the vehicle mayslow down or speed up slightly, whiledriving uphill or downhill.
i
5-39
Driving your vehicle05
OVI055028N
OVI055029N