2016 Hyundai Equus tow

Recalling the Position Memory
1. Check that the shift lever is in P(Park) and the Engine Start/Stop
button is ON.
2. Press the memory button (1 or 2) to recall the desired position.
There will be a beeping sound.
Then, the driver’s seat, outside
rearview mirrors, steering wheel
and HUD (Head-Up Display)
height will be automatically adjust-
ed, as set in the memory.
While the pre-set position is being
recalled, pressing one of the control
buttons for the driver’s seat, the out-
side rearview mirror, or the steering
wheel will stop the movement of that
component in that position. Other
components will be continuously
adjusted, as set in the memory.
Easy Access Function
When the engine is turned OFF, and
when the driver exits from the vehi-
cle, the steering wheel moves away
from the driver, and the seat moves
backwards. After entering the vehi-
cle, the steering wheel will move
toward the driver. After turning the
Engine Start/Stop button to the ACC
position, the seat will move forwards.
You can activate or deactivate the
Easy Access Function in the User
Setting Mode. Refer to "User Setting
Mode" in this chapter.
3-41
Convenient features of your vehicle03
Use caution when recalling the
position memory while sitting in
the vehicle. Immediately push
the seat position control knob,
when the seat moves too far in
any direction.
WARNING

Electronic Hydraulic Power
Steering (EHPS)
This system uses an electromotor to
assist your steering. When the
engine is turned OFF, or when the
EHPS becomes inoperative, you
may still steer the vehicle, but it
requires more effort in steering.
When you notice such a change
while steering, have the EHPS
checked by an authorized EQUUS
dealer.
Do not turn the steering wheel to
the extreme right or left for five
seconds or over, while running the
engine. This may cause damage to
the EHPS motor pump.
Information
When there is a malfunction with the
EHPS motor pump, the efforts to steer
may greatly increase.
Information
When the vehicle is parked outside for
an extended period of time at a cold
temperature (below 14°F/-10°C), the
power steering may require more
efforts, after first starting the engine.
This is due to the increased fluid vis-
cosity at a cold temperature and does
not indicate a malfunction.
When this happens, depress the accel-
erator to increase the engine RPM,
until it reaches 1,500 rpm. Then, let
the engine idle for two-to-three min-
utes to warm up the fluid.
Tilt Steering/Telescope Steering
Adjust the steering wheel angle (2)
and position (3) with the knob (1) on
the steering column. Move the steer-
ing wheel, so it points toward your
chest, not toward your face. Make
sure you can monitor the warning
lights and gauges on the instrument
cluster. After adjusting, slightly push
up and down the steering wheel to
assure that it is locked in position.
Always adjust the position of the
steering wheel before driving.
i
i
NOTICE
S ST
T E
EE
ER
R I
IN
N G
G
W
W H
HE
EE
EL
L
3-42
Convenient features of your vehicle
OVI045034N
NEVER adjust the steering
wheel while driving. This may
cause loss of vehicle control,
resulting in an accident.
WARNING

Electric chromic mirror (ECM) (if equipped)
The electric chromic mirror automat-
ically controls the glare from the
headlamps of the vehicles behind
during the night time or low light driv-
ing conditions. The sensor mounted
in the mirror senses the light level
around the vehicle, and automatical-
ly controls the headlamp glare from
following vehicles.
When the engine is running, the
glare is automatically controlled by
the sensor mounted in the rearview
mirror.
Whenever the shift lever is in R
(Reverse), the mirror automatically
sets to be in the brightest mode in
order to improve the driver's
rearview. When the ECM inside the
rear view mirror operates, it will oper-
ate.
When cleaning the mirror, use a
paper towel or clean cloth damp-
ened with glass cleaner. Do not
spray glass cleaner directly on the
mirror as that may cause the liq-
uid cleaner to enter the mirror
housing.
Reverse Parking Aid Function
When you set the shift lever in R
(Reverse), the outside rearview mir-
ror(s) will slightly rotate downwards
to aid the driver to drive backwards.
The position of the outside rearview
mirror switch (1) determines whether
or not the mirrors will move:
Left/Right: When either the L or R
switch is selected, both
outside rearview mirrors
will move.
Neutral: When neither of the switch-
es is selected, the outside
rearview mirrors will not
move.
The outside rearview mirrors will
automatically reset to their default
positions, when one of the followings
occurs:
The Engine Start/Stop Button is pressed to either the OFF position
or the ACC position.
The shift lever is not in R(Reverse).
The outside rearview mirror switch is not selected.
NOTICE
3-61
Convenient features of your vehicle03
OVI045033N

Tachometer
The tachometer indicates the
approximate number of engine revo-
lutions per minute (rpm).
Use the tachometer to find the cor-
rect shift points and to prevent lug-
ging and/or over-revving the engine.
Do not operate the engine when
the tachometer pointer is in the
RED ZONE. This may cause severe
engine damage.
Engine Coolant TemperatureGauge
This gauge indicates the tempera-
ture of the engine coolant when the
engine is running.
If the gauge pointer moves out of
the normal range area, toward the
“H” position, it indicates overheat-
ing of the engine that may damage
the engine.
Do not continue driving with an
overheated engine. If your vehicle
is overheated, refer to “If the Engine
Overheats” in the chapter 6.
NOTICE
NOTICE
3-66
Convenient features of your vehicle
OVI045611N
■Type A
OVI045612N
■ Type BOVI045613N
■Type A
OVI045614N
■ Type B

- ECS Warning Message
When the Electronic ControlledSuspension (ECS) Warning
Message illuminates due to the
under-pressure inside the sus-
pension, the vehicle height will be
very low. In this case, do not drive
the vehicle in order to protect it
from a projection on a surface. In
this case, have your vehicle
inspected by an authorized
EQUUS dealer.
When towing the vehicle, you should follow the "Electronic
Controlled Suspension (ECS)"
instructions in the chapter 5.
Check SCC System
This warning message illuminates, when there is a malfunction with
the advanced smart cruise control
system. In this case, have your
vehicle inspected by an authorized
EQUUS dealer.
❈ For further information, refer to
"Advanced Smart Cruise Control
System" in the chapter 5.
Check SCC Radar
This warning message illumi-
nates, when the radar of the
advanced smart cruise control
system or its cover is stained.
Remove the stains with a soft
cloth.
❈ For further information, refer to
"Advanced Smart Cruise Control
System" in the chapter 5.
NOTICE
3-85
Convenient features of your vehicle03
OVI045748
OVI045749

To flash the headlamps, pull the lever
towards you. It will return to the
default (low beam) position when
released. The headlamp switch does
not need to be ON to flash the head-
lamps.
Turn signals and lane change
signals
The ignition switch must be ON to
turn ON the turn signals. To turn ON
the turn signals, move the lever up or
down (A). Green arrow indicators on
the instrument panel indicate which
turn signal is operating. They will be
automatically OFF after a vehicle
completes a turn. If the indicator con-
tinues to flash after a turn, manually
return the lever to the OFF position.
To signal a lane change, move the
turn signal lever slightly and hold it in
position (B). The lever will return to
the OFF position when released.
If an indicator stays on and does not
flash or if it flashes abnormally, one
of the turn signal bulbs may be
burned out and require replacement.
One-touch triple turn signal
To activate a one-touch triple turn
signal, move the turn signal lever
slightly for less than 1.8 seconds and
then release it. The lane change sig-
nals will flash three times.
You can activate or deactivate this
function. Refer to the “User Settings”
in this chapter.
3-112
Convenient features of your vehicle
OVI045620N
OVI045621N

Windshield washer
In the OFF position, pull the lever
gently toward you to spray window
washer fluid on the windshield and
operate the wipers one to three
times.
Use this function when the wind-
shield is dirty.
The spray and wiper operation will
continue until you release the lever.
If the washer does not work, check
the washer fluid level. If the fluid level
is not sufficient, you will need to add
authorized non-abrasive windshield
washer fluid to the washer reservoir.
The reservoir filler neck is located in
the front of the engine compartment
in the passenger side.
To prevent possible damage to the
washer pump, do not operate the
washer when the fluid reservoir is
empty. To prevent possible damage to
the wipers or windshield, do not
operate the wipers when the
windshield is dry.
To prevent damage to the wiper blades, do not use gasoline,
kerosene, paint thinner, or other
solvents on or near them.
To prevent damage to the wiper arms and other components, do
not manually attempt to move
the wipers.
NOTICE
NOTICE
3-117
Convenient features of your vehicle03
OVI045099N
Do not use the washer in freez-
ing temperatures before warm-
ing the windshield with the
defrosters; the washer fluid
could be frozen on contact with
the windshield and obscure
your vision.
WARNING

3-128
Convenient features of your vehicle
Front button
The mode selection button controls
the air flow direction from the ventila-
tion system.The air flow outlet can be converted
as follows:
Face-Level (B, D, F, G)
Air flow is directed toward the upper
body and face. Additionally, each air
outlet port can be controlled and
directed manually.
Bi-Level (B, C, D, E, F, G, H)
Air flow is directed toward the face
and the floor.
Floor & Defrost
(A, C, E, D, G, H)
Most of the air flow is directed to the
floor and the windshield, while a
small amount of the air flow is direct-
ed to the side window defrosters.
Floor-Level (A, C, E, D, G, H)
Most of the air flow is directed to the
floor, while a small amount of the air
flow is directed to the windshield and
side window defrosters.
OVI045115N
■
Front
OVI045403N
■
Rear - Type A
OVI045416N
■
Rear - Type B