2016 Hyundai Creta clock

7-50
Maintenance
Reset items
Items should be reset after the bat
tery has been discharged or the bat
tery has been disconnected.
• Auto up/down window (See chapter 3)
• Climate control system (See chapter 3)
• Audio (See chapter 3)
• Clock (See chapter3)
• Trip computer (See chapter 3)
When recharging the battery,
observe the following precautions:
•Before performing maintenance or
recharging the battery, turn off all
accessories and stop the engine.
•Do not allow cigarettes, sparks, or
flame near the battery.
•Wear eye protection when
checking the battery during
charging.
•The battery must be removed
from the vehicle and placed in
an area with good ventilation.
•Watch the battery during charg
ing, and stop or reduce the
charging rate if the battery cells
begin gassing (boiling) violently
or if the temperature of the elec
trolyte of any cell exceeds 49°C
(120°F).
(Continued)
WARNING (Continued)
•The negative battery cable must
be removed first and installed
last when the battery is discon
nected.
•Disconnect the battery charger in
the following order.
1. Turn off the battery charger
main switch.
2. Unhook the negative clamp
from the negative battery ter
minal.
3. Unhook the positive clamp
from the positive battery ter
minal.

7-65
7
Maintenance
3. Pull the suspected fuse straight
out. Use the fuse puller provided in
the engine compar tment fusepanel.
4. Check the removed fuse; replace it if it is blown.
5. Push in a new fuse of the same rating, and make sure it fits tightly
in the clips.
If it fits loosely, we recommend that
you consult an authorized HYUNDAI
dealer.
If you do not have a spare, use a fuse of the same rating from a circuityou may not need for operating thevehicle, such as the cigarette lighterfuse.
If the electrical components do not
work and the fuses are OK, check
the fuse panel in the engine com
partment. If a fuse is blown, it must
be replaced. Fuse switch
Always, put the fuse switch at the ON position.
If you move the switch to the OFF
position, some items such as audio
and digital clock must be reset and
transmitter (or smart key and burglar
alarm) may not work properly.
Always place the fuse switch in the
ON position while driving the vehicle.
NOTICE
OGS075064
OGS075018

7-70
Maintenance
ITEMNameSymbolFuse RatingCircuit Protected
FUSE
BRAKE
SWITCH10AStop Lamp Switch, Smart Key Control Module
HTD IND10AA/C Control Module (Manual, Auto), G4FC : ECU(MT), PCU(AT)
BLOWER110AAC Control Module (Auto)
REAR WIPER10ARear Wiper Motor, Rear Wiper Relay
SPARE10A
SPARE15A
MEMORY10ADigital Clock, Body Control Module, AC Control Module (Auto, Manual), Cluster,
Outside Mirror Folding , OBD
MULTIMEDIA20AAudio
SPARE10A
C_LIGHTER20ACigar lighter (Export only)
INTERIOR LP 10ARoom Lamp, MAP Lamp, Luggage Lamp
BLOWER SIGNAL210AAC Control Module (Manual)
SPARE20A
* G4FC : Gamma 1.6 (Gasoline), D4FC : UII 1.4 (Diesel), D4FB : UII 1.6 (Diesel)

7-71
7
Maintenance
ITEMNameSymbolFuse RatingCircuit Protected
FUSE
ACCACC10AAudio, Body Control Module, P/OUTLET Relay, Digital Clock, Smart Key Module,
Outside Mirror Switch
P/Seat 30APower Seat(Export only)
P/WINDOWRHRH25APower Window Main Switch RH(Front, Rear)
POWER
OUTLET POWER
OUTLET
FR20AFront Power Outlet
TCU15AM/T : Vehicle Speed Sensor, Back Up Lamp Fuse
A/T : Inhibitor Switch, TCU
MODULE 2MODULE
210ABody Control Module, Sports Mode Switch(A/T), Stop Switch (NC)
MODULE 3MODULE
310AA/C Control Module(Manual/Auto), Body Control Module(Static Bending LP Power),
ATM Lever Indicator (A/T)
MODULE 1MODULE
110ARear Parking Sensor
MDPS10AMDPS Unit
AIRBAG INDIND10AInstrumental Cluster
SAFETY
P/WINDOWSAFETY25ADriver Safety Power Window Module
P/WINDOW LHLH25APower Window Main Switch LH(Front Rear)
* G4FC : Gamma 1.6 (Gasoline), D4FC : UII 1.4 (Diesel), D4FB : UII 1.6 (Diesel)

7-80
Maintenance
Headlight (Low/High)
1. Open the hood.
2. Remove the headlight bulb cover by turning it counterclockwise.
3. Disconnect the headlight bulb socketconnector.
4. Unsnap the headlight bulb retain ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head light assembly. 6. Install a new headlight bulb and
snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Turn signal light
1. Remove the turn signal light bulbcover by turning it counterclock
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
OGS075050
Turn signal lightParking
(Position) light
Headlight

7-81
7
Maintenance
Parking (Position) light
1. Remove the socket from the
assembly by pulling it straight out.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb by inserting it into the socket.
4. Install the socket in the assembly by pushing it in.
Front fog light bulb replacement
1. Remove the under cover by rotating the screws and bolts.
2. Reach your hand into the back of the front bumper.
3. Disconnect the power connector from the socket.
4. Remove the bulbsocket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5. Install the new bulbsocket into the housing by aligning the tabs on
the socket with the slots in the
housing. Push the socket into the
housing and turn the socket clock
wise.
6. Connect the power connector to the socket.
7. Reinstall the front bumper under cover.
Type B
(1) Headlight (Low/High)
(2) Parking (Position) light
(3) Front turn signal light
(4) Static bending light
(5) Front fog light (if equipped)
(6) Daytime running light (if equipped)
OGS075055

7-82
Maintenance
Information
If the headlight aiming adjustment is
necessary after the headlight assembly
is reinstalled, consult an authorized
HYUNDAI dealer.
Headlight (Low/High) and static
bending light replacement
1. Open the hood.
2. Remove the headlight bulb cover by turning it counterclockwise.
3. Disconnect the headlight bulb socketconnector.
4. Unsnap the headlight bulb retain ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head light assembly.
i
•Always handle them carefully,
and avoid scratches and abra
sions. If the bulbs are lit, avoid
contact with liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burst when lit. A
bulb should be operated only
when installed in a headlight.
•If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.Halogen bulbs
•Halogen bulbs contain pressur
ized gas that will produce flying
pieces of glass if broken.
(Continued)
(Continued)
WARNING
OLMB073042L
OGS075051
Static bending light
Turn signal
Low/High

7-83
7
Maintenance
6. Install a new headlight bulb and
snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
BiFunction projection
headlamp
This headlamp is bifunction type that
switches the low beam to high or the
high beam to low using solenoid sys
tem. So, the moving sound may be
heard when the headlamp switches
the low beam to high or the high beam
to low and it does not indicate mal
function of the headlamp.
Turn signal light
1. Remove the turn signal light bulb cover by turning it counterclock
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
Front fog light bulb replacement
1.Remove the under cover by rotating the screws and bolts.
2.Reach your hand into the back of the front bumper.
3.Disconnect the power connector from the socket.
4.Remove the bulbsocket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5.Install the new bulbsocket into the housing by aligning the tabs on the
socket with the slots in the hous
ing. Push the socket into the hous
ing and turn the socket clockwise.
6.Connect the power connector to the socket.
7.Reinstall the front bumper under cover.
i