2016 Hyundai Creta wheel

7-54
Maintenance
Tire rotation
To equalize tread wear, it is recom
mended that the tires be rotated
every 12,000 km (7,500 miles) or
sooner if irregular wear develops.
During rotation, check the tires for
correct balance.
When rotating tires, check for uneven
wear and damage. Abnormal wear is
usually caused by incorrect tire pres
sure, improper wheel alignment, out
ofbalance wheels, severe braking or
severe cornering. Look for bumps or
bulges in the tread or side of tire.
Replace the tire if you find either of
these conditions. Replace the tire if
fabric or cord is visible. After rotation,
be sure to bring the front and rear tire
pressures to specification and check
lug nut tightness.
Refer to “Tire and wheels” in chapter
8.Disc brake pads should be inspected
for wear whenever tires are rotated.
Information
Rotate radial tires that have an asym
metric tread pattern only from front
to rear and not from right to left.i
CBGQ0706
CBGQ0707
CBGQ0707A
Without a spare tire
With a fullsize spare tire (if equipped)
Directional tires (if equipped)
•Do not use the compact spare
tire for tire rotation.
•Do not mix bias ply and radial
ply tires under any circum
stances. This may cause unusu
al handling characteristics that
could result in death, severe
injury, or property damage.
WARNING

7-55
7
Maintenance
Wheel alignment and tire bal
ance
The wheels on your vehicle were
aligned and balanced carefully at the
factory to give you the longest tire life
and best overall performance.
In most cases, you will not need to
have your wheels aligned again.
However, if you notice unusual tire
wear or your vehicle pulling one way
or the other, the alignment may need
to be reset.
If you notice your vehicle vibrating
when driving on a smooth road, your
wheels may need to be rebalanced.
Improper wheel weights can damage
your vehicle's aluminum wheels. Use
only approved wheel weights.
Tire replacement
If the tire is worn evenly, a tread wear
indicator will appear as a solid band
across the tread. This shows there is
less than 1.6 mm (1/16 inch) of tread
left on the tire. Replace the tire when
this happens.
Do not wait for the band to appear
across the entire tread before replac
ing the tire.
When replacing the tires, recheck
and tighten the wheel nuts after driv
ing about 1,000 km (620 miles). If the
steering wheel shakes or the vehicle
vibrates while driving, the tire is out
of balance. Align the tire balance. If
the problem is not solved, we recom
mend that you contact an authorized
HYUNDAI dealer.
NOTICE
NOTICE
OEN076053
Tread wear indicator

7-56
Maintenance
Wheel replacement
When replacing the metal wheels for
any reason, make sure the new
wheels are equivalent to the original
factory units in diameter, rim width
and offset.
Replacing tires
To reduce the chance or serious
or fatal injuries from an accident
caused by tire failure or loss of
vehicle control:
•Replace tires that are worn,
show uneven wear, or are dam
aged. Worn tires can cause loss
of braking effectiveness, steer
ing control, and traction.
•Do not drive your vehicle with
too little or too much pressure in
your tires. This can lead to
uneven wear and tire failure.
•When replacing tires, never mix
radial and biasply tires on the
same car. You must replace all
tires (including the spare) if mov
ing from radial to biasply tires.
(Continued)
(Continued)
WARNING •Using tires and wheel other than
the recommended sizes could
cause unusual handling charac
teristics and poor vehicle con
trol, resulting in a serious acci
dent.
•Wheels that do not meet
HYUNDAI's specifications may
fit poorly and result in damage to
the vehicle or unusual handling
and poor vehicle control.
•The ABS works by comparing
the speed of the wheels. Tire
size can affect wheel speed.
When replacing tires, all 4 tires
must use the same size original
ly supplied with the vehicle.
Using tires of a different size can
cause the ABS (Antilock Brake
System) and ESC (Electronic
Stability Control) to work irregu
larly. (if equipped)
A wheel that is not the correct size
may adversely affect wheel and
bearing life, braking and stopping
abilities, handling characteristics,
ground clearance, bodytotire
clearance, snow chain clearance,
speedometer and odometer cali
bration, headlight aim and bumper
height.
WARNING

7-57
7
Maintenance
Tire traction
Tire traction can be reduced if you
drive on worn tires, tires that are
improperly inflated or on slippery
road surfaces. Tires should be
replaced when tread wear indicators
appear. Slow down whenever there
is rain, snow or ice on the road, to
reduce the possibility of losing con
trol of the vehicle.
Tire maintenance
In addition to proper inflation, correct
wheel alignment helps decrease tire
wear. If you find a tire worn unevenly,
have your dealer check the wheelalignment.
When you have new tires installed,
make sure they are balanced. This
will increase vehicle ride comfort and
tire life. Additionally, a tire should
always be rebalanced if it is removed
from the wheel.
Tire sidewall labeling
This information identifies and
describes the fundamental charac
teristics of the tire and also provides
the tire identification number (TIN)
for safety standard certification. The
TIN can be used to identify the tire in
case of a recall.
1. Manufacturer or brand name
Manufacturer or Brand name is shown.
2. Tire size designation
A tire’s sidewall is marked with a tire
size designation. You will need this
information when selecting replace
ment tires for your car. The following
explains what the letters and num
bers in the tire size designationmean.
Example tire size designation:
(These numbers are provided as an
example only; your tire size designa
tor could vary depending on your
vehicle.)
205/65R16 95H
205 Tire width in millimeters.
65 Aspect ratio. The tire’s chapter height as a percentage of its width.
R Tire construction code (Radial).
16 Rim diameter in inches.
95 Load Index, a numerical code associated with the maximum
load the tire can carry.
H Speed Rating Symbol. See the speed rating chart in this chapter
for additional information.
I030B04JM
1
1
23
4
5,6
7

7-58
Maintenance
Wheel size designation
Wheels are also marked with impor
tant information that you need if you
ever have to replace one. The follow
ing explains what the letters and
numbers in the wheel size designa
tion mean.
Example wheel size designation:
6.0JX16
6.0 Rim width in inches.
J Rim contour designation.
16 Rim diameter in inches.
Tire speed ratings
The chart below lists many of the dif
ferent speed ratings currently being
used for passenger car tires. The
speed rating is part of the tire size
designation on the sidewall of the
tire. This symbol corresponds to that
tire's designed maximum safe oper
ating speed.
3. Checking tire life (TIN : Tire
Identification Number)
Any tires that are over 6 years old,
based on the manufacturing date,
(including the spare tire) should be
replaced by new ones. You can find
the manufacturing date on the tire
sidewall (possibly on the inside of the
wheel), displaying the DOT Code.
The DOT Code is a series of num
bers on a tire consisting of numbers
and English letters. The manufactur
ing date is designated by the last four
digits (characters) of the DOT code.
DOT : XXXX XXXX OOOO
The front part of the DOT means a
plant code number, tire size and
tread pattern and the last four num
bers indicate week and year manu
factured.
For example:
DOT XXXX XXXX 1615 represents
that the tire was produced in the 16th
week of 2015.
S 180 km/h (112 mph) T 190 km/h (118 mph)
H 210 km/h (130 mph) V 240 km/h (149 mph) Z Above 240 km/h (149 mph)
W *270 km/h (168 mph)
Maximum SpeedSpeedRatingSymbol
* W speed rating is subcategory of the Z speed rating.

7-60
Maintenance
Tread wear
The tread wear grade is a compara
tive rating based on the wear rate of
the tire when tested under controlled
conditions on a specified govern
ment test course. For example, a tire
graded 150 would wear oneanda
half times (1) as well on the gov
ernment course as a tire graded 100.
The relative performance of tires
depends upon the actual conditions
of their use, however, and may
depart significantly from the norm
due to variations in driving habits,
service practices and differences in
road characteristics and climate.
These grades are molded on the
sidewalls of passenger vehicle tires.
The tires available as standard or
optional equipment on your vehicle
may vary with respect to grade.
Traction AA, A, B & C
The traction grades, from highest to
lowest, are AA, A, B and C. Those
grades represent the tire’s ability to
stop on wet pavement measured
under controlled conditions on spec
ified government test surfaces of
asphalt and concrete. A tire marked
C may have poor traction perform
ance.
Temperature A, B & C
The temperature grades are A (the
highest), B, and C, representing the
tire’s resistance to the generation of
heat and its ability to dissipate heat
when tested under controlled condi
tions on a specified indoor laboratory
test wheel.
Sustained high temperature can
cause the material of the tire to
degenerate and reduce tire life, and
excessive temperature can lead to
sudden tire failure. Grades B and A
represent higher levels of perform
ance on the laboratory test wheel
than the minimum required by law.
The traction grade assigned to this
tire is based on straightahead
braking traction tests, and does
not include acceleration, corner
ing, hydroplaning, or peak traction
characteristics.
WARNING

7-61
7
Maintenance
Low aspect ratio tire
(if equipped)
The low aspect ratio tires, of which
aspect ratio is below 50, are
equipped with for the sporty look.
Riding with high aspect ratio tires
may be uncomfortable with unpleas
ant noises, because the low aspect
ratio tires are optimized for handling
and breaking.The sidewall of the low aspect ratio
tire is thinner than the high aspect
ratio tire. Thus, the wheel and the tire
may be easily damaged. Thus, follow
the below instructions.
Cautiously drive the vehicle on a
rough road or off the road.
Otherwise, the tires and wheels
may be damaged. After driving
those areas, inspect the tires and
wheels.
Slowly drive the vehicle to pass
over a pothole, speed bump, man
hole, or curb stone. Otherwise, the
tires and wheels may be damaged.
Upon having an impact on the tire,
we recommend you to have the
tires inspected by an authorized
HYUNDAI dealer.
Inspect the tires every 3,000 km to
prevent damage.
NOTICE
Tire temperature
The temperature grade for this tire
is established for a tire that is
properly inflated and not over
loaded. Excessive speed, under
inflation, or excessive loading,
either separately or in combina
tion, can cause heat buildup and
sudden tire failure. This can cause
loss of vehicle control and serious
injury or death.
WARNING

7-91
7
Maintenance
Brightmetal maintenance
• To remove road tar and insects,use a tar remover, not a scraper or
other sharp object.
• To protect the surfaces of bright metal parts from corrosion, apply a
coating of wax or chrome preser
vative and rub to a high luster.
• During winter weather or in coastal areas, cover the bright metal parts
with a heavier coating of wax or
preservative. If necessary, coat the
par ts with noncorrosive gasoli
neeum jelly or other protective
compound.
Underbody maintenance
Corrosive materials used for ice and
snow removal and dust control may
collect on the underbody. If these
materials are not removed, acceler
ated rusting can occur on the under
body parts such as the fuel lines,
frame, floor pan and exhaust system,
even though they have been treated
with rust protection.
Thoroughly flush the vehicle under
body and wheel openings with luke
warm or cold water once a month,
after offroad driving and at the end
of each winter. Pay special attention
to these areas because it is difficult
to see all the mud and dirt. It will do
more harm than good to wet down
the road grime without removing it.
The lower edges of the doors, rocker
panels, and frame members have
drain holes that should not clog with
dirt; trapped water in these areas can
cause rusting.
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by
water. If braking performance is
impaired, dry the brakes by apply
ing them lightly while maintaining
a slow forward speed.
WARNING