2016 HONDA FIT warning

106 || 107
HANDLING THE UNEXPECTED
HANDLING THE UNEXPECTED
Replacing the Flat Tire
1. Remove the wheel nuts and at tire.
2. Mount the compact spare tire. Replace the
wheel nuts, and lightly tighten them.
3. Lower the vehicle and remove the jack. Tighten the wheel nuts in the order indicated in the image. Go around, tightening the nuts, two to
three times in this order. Do not overtighten the  wheel nuts. Models with wheel covers: Make sure the wire
support ring is hooked into the clips around the
edge of the wheel cover. Align the valve mark on the wheel cover to the tire valve on the wheel, then install the wheel
cover.
If you drive with the spare tire installed, the low tire pressure/TPMS indicator*  appears. The indicator stays on until a regular tire is installed.
*if equippedWheel nuts
Storing the Flat Tire
1. Remove the center cap, if necessary.
2. Place the at tire face down in the spare tire well.
3. Remove the spacer cone from the wing bolt, lip 
it over, and insert it back on the bolt. Secure the lat tire with the wing bolt. Models with wheel covers: Make sure the wire
support ring is on the outer side of the tire valve as shown.
4. Securely store the wheel nut wrench, jack handle bar, and jack back in the tool  case. Store the case in the cargo area under the cargo oor lid.
Loose items can y around the interior in a crash and can seriously injure the occupants. Store the wheel, jack, and tools securely before driving.
WARNING
Wing bolt
Spacer cone
For compact spare tire
For full-size 
tire
Clips
Clips
Valve mark
Tire valve
Wire support ring

112 || 113
MAINTENANCE
MAINTENANCE
Safety Precautions
Some of the most important safety precautions are listed below; however, we cannot  warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.
Maintenance Safety
• 
To reduce the possibility of ire or explosion, keep cigarettes, sparks, and lames 
away from the battery and all fuel-related parts.
•  Never leave rags, towels, or other lammable objects under the hood.
•  To clean parts, use a commercially available degreaser or parts cleaner, not  gasoline.
•  Wear eye protection and protective clothing when working with the battery or 
compressed air.
•  Do not run the engine in conined spaces where carbon monoxide gas can 
accumulate.
Vehicle Safety
•  The vehicle must be stationary, and parked on level ground with the parking 
brake set and the engine off.
•  Be aware that hot parts can burn you. •  Be aware that moving parts can injure you.
Improperly maintaining this vehicle or failing to correct a problem before  driving can cause a crash in which you can be seriously hurt or killed.  Always follow the inspection and maintenance recommendations according to the schedules in this guide.
WARNING
Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed. Always follow the procedures and precautions in this guide.
WARNING
Learn about basic maintenance that you can perform on the vehicle yourself, as well  as information about how to best maintain the vehicle.
MAINTENANCEMaintenance Minder™
When maintenance is due, the Maintenance Minder indicator comes on and a
message appears on the display every time you turn the vehicle on. Press the select/reset knob to change displays. See the service code table on page 114 to check which items need maintenance 
based on the main and sub items shown in the display.
Maintenance Minder indicatorMain items
Sub items
Maintenance Minder display
•  Independent of the Maintenance Minder information, replace the brake luid every  3 years.
•  Inspect idle speed every 160,000 miles (256,000 km).
•  Adjust the valves during services A, B, 1, 2, or 3 if they are noisy.
U.S. models
Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individuals using parts that
are certied to EPA standards. According to state and federal regulations, failure to perform maintenance on the
maintenance main items marked with # will not void your emissions warranties.
However, all maintenance services should be performed in accordance with the 
intervals indicated by the multi-information display.

118 || 119
MAINTENANCE
MAINTENANCE
Engine Coolant
Park the vehicle on level ground. Check the reserve tank and the coolant level in the
radiator. We recommend Honda Long Life Antifreeze/Coolant Type 2.
Checking the Reserve Tank
1. Check the amount of coolant in the reserve tank. 2. If the coolant level is below the MIN mark, add  the specied coolant until it reaches the MAX mark.
3. Inspect the cooling system for leaks.
Adding Coolant
1. Make sure the engine and radiator are cool.
2. Turn the radiator cap counterclockwise and
relieve any pressure in the coolant system. Do  not push the cap down when turning.
3. Push down and turn the radiator cap counterclockwise to remove it.
4. The coolant level should be up to the base of the 
ller neck. Add coolant if it is low.
5. Put the radiator cap back on, and tighten it fully.
6. Pour coolant into the reserve tank until it reaches the MAX mark. Put the cap back on the reserve tank.
If Honda antifreeze/coolant is not available, you may use another major brand 
non-silicate coolant as a temporary replacement. Check that it is a high quality coolant recommended for aluminum engines. Continued use of any non-Honda
coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system lushed and reilled with Honda antifreeze/coolant as  soon as possible.
NOTICE
Reserve tank
MAX MIN
Radiator cap
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you. Always let the engine and radiator cool down before removing the radiator  cap.
WARNING
Pour the uid slowly and carefully so you do not spill any. Clean up any spills immediately; they can damage components in the engine compartment.
NOTICE
Brake Fluid
The luid level should be between the MIN and MAX marks on the side of the 
reservoir. We recommend using Honda Heavy Duty Brake Fluid DOT 3.
Pour the uid carefully. If the luid level is at or below the MIN mark, have a  dealer inspect for leaks or worn brake pads as soon as possible.
Window Washer Fluid
Check the amount of window washer luid by looking 
at the reservoir. If the washer luid level is low, ill the 
washer reservoir. Pour the washer luid carefully. Do not 
overow the reservoir.
Canadian models
If the washer luid level is low, the washer level  indicator appears (see page 27).
Do not use engine antifreeze or a vinegar/water solution in the windshield washer 
reservoir. Antifreeze can damage your vehicle’s paint. A vinegar/water solution can damage the windshield washer pump.
NOTICE
Washer reservoir
Brake luid marked DOT 5 is not compatible with your vehicle’s braking system  and can cause extensive damage.
NOTICE
MAX
MIN

120 || 121
MAINTENANCE
MAINTENANCE
Changing Wiper Blades
If the wiper blades leave streaks across the windshield, try cleaning them irst with a  paper towel or soft cloth and wiper luid. If the wiper blade rubber has deteriorated, you should change the wiper blades.
Changing the Front Wiper Blade Rubber
1. Lift the driver side wiper arm rst, then the
passenger side.
2. Press and hold the tab, then slide the blade  from the wiper arm.
3. Slide the wiper blade out from its holder by pulling the tabbed end out.
4. Slide the new wiper blade onto the holder from the bottom end. The tab on the blade should it 
in the indent of the top of the wiper holder.
5. Slide the wiper blade onto the wiper arm 
securely.
6. Lower the passenger side wiper arm rst, then the driver side.
Lock tab
Blade
Ta b Blade
Avoid dropping the wiper arm, as it may damage the windshield.
NOTICE
The battery gives off explosive hydrogen gas during normal operation. A spark or lame can cause the battery to explode with enough force to kill or  seriously hurt you. When conducting any battery maintenance, wear protective clothing and a  face shield, or have a skilled technician do it.
WARNING
Checking the Battery
The battery condition is monitored by a sensor on the negative terminal. If there is a 
problem with the battery, the charging system indicator appears (see page 24). Have 
your vehicle checked by a dealer.
Check the battery terminals for corrosion monthly.For jump starting, see page 98.
WARNING: Battery posts, terminals, and related accessories contain lead and lead
compounds. Wash your hands after handling.

124 || 125
MAINTENANCE
MAINTENANCE
Tire and Loading Information Label
The label attached to the driver’s doorjamb provides necessary tire and  loading information. Using tires that are excessively worn or improperly inated can cause a crash in which you can be seriously hurt or killed.
Follow all instructions in this owner’s manual regarding tire ination and maintenance
.
WARNING
Original tire sizesNumber of  people your vehicle can carry Proper cold tire pressure
Total weight your vehicle can carry (do not exceed)
Tire and Wheel Replacement
Replace your tires with radials of the same size, load range, speed rating, and 
maximum cold tire pressure rating (as shown on the tire’s sidewall). Using tires
of a different size or construction can cause certain vehicle systems to work 
incorrectly. It is best to replace all four tires at the same time. If that isn’t possible, replace the front or rear tires in pairs.
If you change or replace a wheel, make sure that the wheel’s speciications match  those of the original wheels.
Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.
Always use the size and type of tires recommended in the Owner’s Manual.
WARNING
Tire Service Life
The life of your tires is dependent on many factors, including driving habits, road 
conditions, vehicle loading, ination pressure, maintenance history, speed, and environmental conditions (even when the tires are not in use). In addition to regular inspections and inlation pressure maintenance, it is  recommended that you have annual inspections performed once the tires reach
ive years old. All tires, including the spare, should be removed from service after 10 years from the date of manufacture, regardless of their condition or state of
wear.
Winter Tires
If driving on snowy or frozen roads, mount all season tires marked “M+S”, snow  tires, or tire chains; reduce speed; and maintain suficient distance between 
vehicles when driving. For winter tires, select the size and load ranges that are the same as the original tires, and mount them to all four wheels.
Tire Chains
Install tire chains on the front tires only. Because your vehicle has limited tire  clearance, we strongly recommend using the following chains: Cable type: SCC
Radial Chain SC1026. Mount chains as tightly as you can, and make sure that they do not touch the brake lines or suspension.
Traction devices that are the wrong size or improperly installed can damage your 
vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.
NOTICE
Using the wrong chains, or not properly installing chains, can damage the brake lines and cause a crash in which you can be seriously injured or killed.
Follow all instructions in this guide regarding the selection and use of tire chains.
WARNING

128 || 129
MAINTENANCE
MAINTENANCE
Temperature
The temperature grades are A (the highest), B, and C, representing the tire’s
resistance to the generation of heat and its ability to dissipate heat when tested  under controlled conditions on a speciied indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce
tire life, and excessive temperature can lead to sudden tire failure. The grade
C corresponds to a level of performance which all passenger car tires must
meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the 
minimum required by law.
WARNING:  The temperature grade for this tire is established for a tire that 
is properly inlated and not overloaded. Excessive speed, underinlation, or  excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
Testing of Readiness Codes
Your vehicle has “readiness codes” as part of the onboard self-diagnostic system. 
Some states refer to these codes as a test to see if your vehicle’s emissions
components are working properly. The codes may not be read if you go through the emissions testing just after the battery has gone dead or been disconnected.
To check if they are set, turn the vehicle on without starting the engine. The
malfunction indicator lamp will come on for several seconds. If it goes off, the 
readiness codes are set. If it blinks ive times, the readiness codes are not set.
If you are required to have your vehicle emissions tested before the readiness codes  are set, prepare the vehicle for retesting by doing the following: 1. Fill the gas tank to approximately 3/4 full.
2. Park the vehicle and leave the engine off for 6 hours or more.3. Make sure the ambient temperature is between 40°F and 95°F (4°C and 35°C).
4. Start the engine without touching the accelerator pedal, and let it idle for 20 seconds.
5. Keep the vehicle in Park (P) or Neutral (manual transmission). Increase the 
engine speed to 2,000 rpm, and hold it there for about 3 minutes.
6. Let the engine idle with your foot off the accelerator for 20 seconds. 7. Select a nearby, lightly traveled major highway where you can maintain a speed 
of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway with 
the vehicle in Drive (D) or 5th gear (manual transmission). Do not use cruise 
control. When trafc allows, drive for 90 seconds without using the accelerator
pedal. (Vehicle speed may vary slightly; this is OK.) If you cannot do this for a continuous 90 seconds because of trafic conditions, drive for at least 30 seconds, then repeat two more times (for a total of 90 seconds).
8. Drive in city/suburban trafic for at least 10 minutes. When trafic conditions 
allow, let the vehicle coast for several seconds without using the accelerator pedal or the brake pedal.
9. Park the vehicle and leave the engine off for 30 minutes. The readiness codes are erased when the battery is disconnected, and set again  only after several days of driving under a variety of conditions. If an emissions testing facility determines that the readiness codes are not set, you 
may be requested to return at a later date to complete the test, or see your dealer.