
Continued421
uuWhen Driving uAdaptive Cruise Control (ACC) with Low Speed Follow (LSF)*
Driving
The system may automatically shut off and the  ACC indicator will come on under 
certain conditions. Some examples of these conditions  are listed below. Other 
conditions may reduce some of the ACC functions.
2 Front Sensor Camera* P. 414
■Environmental conditions
• Driving in bad weather (rain, fog, snow, etc.).
■Roadway conditions
• Driving on a snowy or wet roadway (obs cured lane marking, vehicle tracks, 
reflected lights, road  spray, high contrast).
■Vehicle conditions
• The outside of the windshield is blocked by dirt, mud, leaves, wet snow, etc.
• An abnormal tire or wheel condition (Wrong size, varied size or construction, 
improperly inflated, co mpact spare tire, etc.).
• The camera temperature gets too high.
• The parking brake is applied.
• When the lower bumper next to the fog light is dirty.
• When the front of the vehicle  tilts up due to heavy cargo in the trunk or rear seats.
• When tire chains are installed.
■ACC with LSF Conditions and Limitations1ACC with LSF Conditions and Limitations
The radar sensor for ACC with LSF is shared with the 
collision mitigation braking system
TM (CMBSTM).
2 Collision Mitigation Braking SystemTM 
(CMBSTM)* P. 459
You can read about handling information for the 
camera equipped with this system. 2 Front Sensor Camera
* P. 414
Do not put a sticker on the radar sensor cover or 
replace the radar sensor cover.
Have your vehicle checked by a dealer if you find any 
unusual behavior of the system (e.g., the warning 
message appears too frequently).
If the front of the vehicle is impacted in any of the 
following situations, the ra dar sensor may not work 
properly. Have your vehi cle checked by a dealer:
•The vehicle mounted onto a bump, curb, chock, 
embankment, etc.
•You drive the vehicle where the water is deep.
•Your vehicle has a frontal collision.
* Not available on all models
16 CIVIC 4D-31TBA6000.book  421 ページ  2015年8月31日 月曜日 午後5時56分 

433
uuWhen Driving uRoad Departure Mitigation (RDM) System*
Driving
■Roadway conditions
• Driving on a snowy or wet roadway (obs cured lane marking, vehicle tracks, 
reflected lights, road  spray, high contrast).
• Driving on a road with temporary lane markings.
• Faint, multiple, or varied lane markings  are visible on the roadway due to road 
repairs or old lane markings.
• The roadway has merging, split, or crossing  lines (e.g., such as at an intersection 
or crosswalk).
• The lane markings are extremely narrow, wide, or changing.
• The vehicle in front of you is driving near the lane lines.
• The road is hilly or the vehicle  is approaching the crest of a hill.
• Driving on rough or unpaved roads, or over bumpy surfaces.
• When objects on the road (curb, guard rail,  pylons, etc.) are recognized as white 
lines (or yellow lines).
• Driving on roads with double lines.
■Vehicle conditions
• Headlight lenses are dirty or the h eadlights are not properly adjusted.
• The outside of the windshield is streaked  or blocked by dirt, mud, leaves, wet 
snow, etc.
• The inside of the windshield is fogged.
• The camera temperature gets too high.
• An abnormal tire or wheel condition (wrong  sized, varied size or construction, 
improperly inflated, co mpact spare tire, etc.).
• The vehicle is tilted due to a heavy load or  suspension modifications.
• When tire chains are installed.
16 CIVIC 4D-31TBA6000.book  433 ページ  2015年8月31日 月曜日 午後5時56分 

440
uuWhen Driving uLane Keeping Assist System (LKAS)*
Driving
■Roadway conditions
• Driving on a snowy or wet roadway (obs cured lane marking, vehicle tracks, 
reflected lights, road  spray, high contrast).
• Driving on a road with temporary lane markings.
• Faint, multiple, or varied lane markings  are visible on the roadway due to road 
repairs or old lane markings.
• The roadway has merging, split, or crossing  lines (e.g., such as at an intersection 
or crosswalk).
• The lane markings are extremely  narrow, wide, or changing.
• The vehicle in front of you is  driving near the lane lines.
• The road is hilly or the vehicle is approaching the crest of a hill.
• Driving on rough or unpaved roads, or over bumpy surfaces.
• When objects on the road (curb, guard rail, pylons, etc.) are recognized as white 
lines (or yellow lines).
• Driving on roads with double lines.
■Vehicle conditions
• Headlight lenses are dirty or the  headlights are not properly adjusted.
• The outside of the windshield is streake d or blocked by dirt, mud, leaves, wet 
snow, etc.
• The inside of the windshield is fogged.
• The camera temperature gets too high.
• An abnormal tire or wheel condition (wrong size, varied size or construction, 
improperly inflated, comp act spare tire, etc.).
• The vehicle is tilted due to a heav y load or suspension modifications.
16 CIVIC 4D-31TBA6000.book  440 ページ  2015年8月31日 月曜日 午後5時56分 

446
uuWhen Driving uTire Pressure Monitoring System (TPMS)
Driving
Tire Pressure Monitoring System (TPMS)
Instead of directly measuring the pressu re in each tire, the TPMS on this vehicle 
monitors and compares the rolling radius  and rotational characteristics of each 
wheel and tire while you are driving to determine if one or more tires are 
significantly under-inflated. This will caus e the low tire pressure/TPMS indicator to 
come on and a message to appear on  the driver information interface
*.
You must start TPMS calibration every time you:
• Adjust the pressure in one or more tires.
• Rotate the tires.
• Replace one or more tires.
Before calibrating the TPMS:
• Set the cold tire pressu re in all four tires.
2Checking Tires  P. 516
Make sure:
•The vehicle is at a complete stop.
• The shift lever is in 
(N.
• The shift lever is in 
(P.
• The ignition switch is in ON 
(w*1.
*1: Models with the smart entry system have an  ENGINE START/STOP button instead of an 
ignition switch.
■TPMS Calibration
U.S. models
1 Tire Pressure Monitoring System (TPMS)
The system does not monitor the tires when driving 
at low speed.
Conditions such as low  ambient temperature and 
altitude change directly a ffect tire pressure and can 
trigger the low tire pressure/TPMS indicator to come on.
Tire pressure checked and inflated in:
•Warm weather can beco me under-inflated in 
colder weather.
•Cold weather can become  over-inflated in warmer 
weather.
The low tire pressure indica tor will not come on as a 
result of over inflation.
The TPMS may not function pr operly if tire type and 
size are mixed. Make sure to use the same size and 
type of tire. 2 Checking and Maintaining Tires  P. 516
The low tire pressure/TPMS indicator may come on 
with a delay or may not  come on at all when:
•You rapidly accelerate, decelerate, or turn the 
steering wheel.
•You drive on snowy or slippery roads.•Snow chains are used.
The low tire pressure/TPMS indicator may come on 
under the following conditions:
•A compact spare tire is used.•There is a heavier and une ven load on the tires, 
such as when towing a trailer, than the condition at 
calibration.
•Snow chains are used.
Manual transmission models
Continuously variable transmission models
All models
* Not available on all models
16 CIVIC 4D-31TBA6000.book  446 ページ  2015年8月31日 月曜日 午後5時56分 

464
uuBraking uCollision Mitigation Braking SystemTM (CMBSTM)*
Driving
■Vehicle conditions
• Headlight lenses are dirty or the  headlights are not properly adjusted.
• The outside of the windshie ld is blocked by dirt, mud, leaves, wet snow, etc.
• The inside of the windshield is fogged.
• An abnormal tire or wheel condition (wrong size, varied size or construction, 
improperly inflated, comp act spare tire, etc.).
• When tire chains are installed.
• The vehicle is tilted due to a heav y load or suspension modifications.
• The camera temperature gets too high.
• Driving with the parking brake applied.
• When the radar sensor in the front grille gets dirty.
■Detection limitations
• A vehicle or pedestrian suddenly crosses in front of you.
• The distance between your vehicle and the  vehicle or pedestrian ahead of you is 
too short.
• A vehicle cuts in front of you at  a slow speed, and it brakes suddenly.
• When you accelerate rapidly and approach the vehicle or pedestrian ahead of you 
at high speed.
• The vehicle ahead of you is  a motorcycle, bicycle, mobility scooter or other small 
vehicle.
• When there are animals in front of your vehicle.
• When you drive on a curved, wi nding or undulating road that makes it difficult for 
the sensor to properly detect a vehicle in front of you.
• The speed difference between your vehicle an d a vehicle or pedestrian in front of 
you is significantly large.
• An oncoming vehicle suddenly comes in front of you.
• Another vehicle suddenly comes in front of you at an intersection, etc.
• Your vehicle abruptly crosses over in front of an oncoming vehicle.
• When driving through a narrow iron bridge.
• When the lead vehicle suddenly slows down.
16 CIVIC 4D-31TBA6000.book  464 ページ  2015年8月31日 月曜日 午後5時56分 

516
Maintenance
Checking and Maintaining Tires
Checking Tires
To safely operate your vehicle, your tires must be of the proper type and size, in 
good condition with adequate tread, and properly inflated.
■Inflation guidelines
Properly inflated tires provide  the best combination of handling, tread life, and comfort. 
Refer to the driver’s doorjamb label or spec ification’s page for the specified pressure.
Underinflated tires wear unevenly, adversely affect handling and fuel economy, and 
are more likely to fail from overheating.
Overinflated tires make your vehicle ride harshly, are more prone to road hazards, 
and wear unevenly.
Every day before you drive, look at each of  the tires. If one looks lower than the 
others, check the pressure with a tire gauge.
At least once a month or before long trips, use a gauge to measure the pressure in 
all tires, including the spare
*. Even tires in good condition can lose 1 to 2 psi (10 to 
20 kPa, 0.1 to 0.2 kgf/cm2) per month.
■Inspection guidelines
Every time you check inflation, also  examine the tires and valve stems.
Look for:
• Bumps or bulges on the side or in the tread. Replace the tire if you find any cuts, 
splits, or cracks in the si de of the tire. Replace it if you see fabric or cord.
• Remove any foreign objects  and inspect for air leaks.
• Uneven tread wear. Have a deal er check the wheel alignment.
• Excessive tread wear.
2 Wear Indicators  P. 521
•Cracks or other damage around valve stem.
1Checking Tires
Measure the air pressure when tires are cold. This 
means the vehicle has been parked for at least three 
hours, or driven less than 1 mile (1.6 km). If 
necessary, add or releas e air until the specified 
pressure is reached.
If checked when hot, tire pressure can be as much as 
4–6 psi (30–40 kPa, 0.3–0.4 kgf/cm
2) higher than if 
checked when cold.
Whenever tire pressure is adjusted, you must 
calibrate the TPMS. 2 TPMS Calibration  P. 446
Have a dealer check the tires if you feel a consistent 
vibration while driving. Ne w tires and any that have 
been removed and reinst alled should be properly 
balanced.
Measure the spare tire pressure once a month or 
before long trips.
3WARNING
Using tires that are excessively worn or 
improperly inflated can cause a crash in 
which you can be seriously hurt or killed.
Follow all instruction s in this owner’s 
manual regarding ti re inflation and 
maintenance.
U.S. models
* Not available on all models
16 CIVIC 4D-31TBA6000.book  516 ページ  2015年8月31日 月曜日 午後5時56分 

537Continued
Handling the Unexpected
If a Tire Goes Flat
Changing a Flat Tire
If a tire goes flat while driving, grasp the steering wheel firmly, and brake gradually 
to reduce speed. Then, stop in a safe plac e. Replace the flat tire with a compact 
spare tire. Go to a dealer as soon as possib le to have the full-size tire repaired or 
replaced.
1. Park the vehicle on firm, level, and non-slippery surface, and apply the parking 
brake.
2. Move the shift lever to 
(P.
2. Move the shift lever to 
(R.
3. Turn on the hazard warning lights an d turn the ignition switch to LOCK 
(0*1.
*1: Models with the smart entry system have an  ENGINE START/STOP button instead of an 
ignition switch.
1 Changing a Flat Tire
Follow compact spare precautions:
Periodically check the tire pressure of the compact 
spare. It should be set to the specified pressure. 
Specified Pressure: 60 psi (420 kPa, 4.2 kgf/cm
2)
When driving with the compact spare tire, keep the 
vehicle speed under 50 mph (80 km/h). Replace with 
a full-size tire as soon as possible.
The compact spare tire and wheel in your vehicle are 
specifically for this model. Do not use them with 
another vehicle. Do not us e another type of compact 
spare tire or wheel with your vehicle.
Do not mount tire chains on a compact spare tire. 
If a chain-mounted front tire  goes flat, remove one of 
the full-size rear tires and replace it with the compact 
spare tire. Remove the flat front tire and replace it 
with the full-size tire that was removed from the rear. 
Mount the tire chains on the front tire.
NOTICE
Do not use the jack if it  doesn’t work properly. Call 
your dealer or a prof essional towing service.
Continuously variable transmission models
Manual transmission models
All models
16 CIVIC 4D-31TBA6000.book  537 ページ  2015年8月31日 月曜日 午後5時56分 

uuIf a Tire Goes Flat uChanging a Flat Tire
538
Handling the Unexpected
1. Open the trunk floor lid.
2. Take the tool case out of the trunk. Take 
the jack and wheel nut wrench out of the 
tool case.
3. Unscrew the wing bolt, and remove the 
spacer cone. Then, remove the spare tire.
4. Place a wheel block or ro ck in front and rear 
of the wheel diagonal to the flat tire.
■Getting Ready to Replace the Flat Tire1 Getting Ready to Replace the Flat Tire
The wheel nut wrench supplie d with your vehicle is 
specially adapted to fit th e holder shaft. Do not use 
any other tool.
Tool Case
Spare Tire
Wheel 
Blocks
The tire to be replaced.
16 CIVIC 4D-31TBA6000.book  538 ページ  2015年8月31日 月曜日 午後5時56分