2016 HONDA CIVIC COUPE change time

108 || 109
DRIVING
DRIVING
LaneWatch™*
Check the passenger-side rear areas in the upper display when the right turn signal is activated.
Activating LaneWatch
Activate the right turn signal. The LaneWatch display appears. Check the display for blind spots, and visually conrm that it is safe to change lanes.
You can also press the LaneWatch button on the end of the turn signal switch to view a constant real-time
display. Press it again to turn the display off.
Changing Settings
Customize the display and how and when the display appears.
1. From the Home screen, select Settings.
2. Select Camera.
3. Select LaneWatch.
4. Select an option and make the preferred
changes.
5. Press BACK to exit the menu.
Important Safety Reminder
LaneWatch has limitations. Over-reliance on the system may result in a collision.
*if equipped
Failure to visually conrm that it is safe to change lanes before doing so may result in a crash and serious injury or death.
Do not rely only on LaneWatch while driving. Always look in your mirrors, to either side of your vehicle, and behind you for other vehicles before changing lanes.
WARNING
LaneWatch display
Multi-View Rear Camera
When you shift into Reverse (R), a real-time image of the area behind your vehicle is
shown in the display, along with helpful parking guidelines.
Wide view
Press the selector knob or touch icons on the screen to change views.
Normal viewTop down view
The rear camera view is restricted. You cannot see the corner ends of the bumper or what is underneath 
the bumper. Its unique lens also makes objects appear closer or farther than they actually are.
Visually conirm that it is safe to drive before backing up. Certain conditions (such as weather, lighting, 
and high temperatures) may also restrict the rear view. Do not rely on the rearview display, which does not give you all the information about conditions at the rear of your vehicle.

118 || 119
HANDLING THE UNEXPECTED
HANDLING THE UNEXPECTED
Tire Pressure Monitoring System (TPMS)
Monitors the tire pressure while you are driving. If your vehicle’s tire pressure becomes
signicantly low, the low tire pressure indicator comes on and a message appears on
the display. Available on U.S. models only.
What to Do
Stop your vehicle in a safe place. Check the tire pressure and adjust the pressure to the specied
level on the label on the driver’s doorjamb.
TPMS Calibration
Any time you inate, change, or rotate one or more of the tires, you need to recalibrate the system.
The calibration process requires approximately 30 minutes of cumulative driving at
speeds between 30–65 mph (48–105 km/h). The vehicle must be stopped to begin
calibration, and the process nishes automatically.
Models with TPMS button
Press and hold the TPMS button until the low tire pressure indicator blinks twice, indicating the calibration process has begun.
Models with color audio system and Driver Information Interface
Use the steering wheel buttons to make and enter selections in the Driver Information Interface (see page 29).
1. Scroll to the Vehicle Settings screen, and select it.
2. Select TPMS Calibration.
3. Select Calibrate.
Models with Display Audio
Touch items on the screen to make and enter selections.
1. From the HOME screen, select Settings.
2. Select Vehicle.
3. Select TPMS Calibration.
4. Select Calibrate.
TPMS button
Low tire pressure/ TPMS indicator

Tire Pressure Monitoring System (TPMS) - Required Federal Explanation
Each tire, including the spare (if provided), should be checked monthly when cold and inated to the ination pressure recommended by the vehicle manufacturer on the vehicle placard or tire ination pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire ination pressure label, you should determine the proper tire ination pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is signicantly underinated.
Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inate them to the proper pressure. Driving on a signicantly underinated tire causes the tire to overheat and can lead to tire failure. Underination also reduces fuel efciency and tire
tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance,
and it is the driver’s responsibility to maintain correct tire pressure, even if underination has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
Your vehicle has also been equipped with a TPMS malfunction indicator to
indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will ash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that
prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate
tires and wheels allow the TPMS to continue to function properly.
Driving on an extremely underinated tire can cause it to overheat. An overheated tire can fail. Always inate your tires to the specied pressure.
NOTICE

128 || 129
MAINTENANCE
MAINTENANCE
Maintenance Minder™
Reminds you when indicated maintenance service is due.
Models with information display
When maintenance is due, the Maintenance Minder indicator comes on and a message
appears on the display every time you turn the vehicle on. Press the TRIP knob in the instrument panel to change displays (see page 28).
Models with Driver Information Interface
When maintenance is due, the system message indicator comes on and a message
appears on the display every time you turn the vehicle on. Press the display/information button on the steering wheel to change displays (see page 29).
Maintenance Minder message
Maintenance
Minder indicator
Sub items
Main item
Maintenance Minder message
System message

indicator
Sub items
Main item
U.S. models
Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individuals using parts that are
certied to EPA standards. According to state and federal regulations, failure to perform maintenance on the
maintenance main items marked with # will not void your emissions warranties.
However, all maintenance services should be performed in accordance with the intervals indicated by the Driver Information Interface.
Maintenance Minder Service Codes
These codes indicate what services are due on your vehicle.
U.S. models
*1: If a Maintenance Minder indicator does not appear more than 12 months after the display is
reset, change the engine oil every year.
#: See information on maintenance and emissions warranty.
CODEMaintenance Main Items
A 
Replace engine oi l*1
B
Replace engine oi l*1
and oil lter
 Inspect front and rear brakes
 Inspect these items:
• Tie rod ends, steering gear box, and boots
•S uspension components
• Driveshaft boots
• Brake hoses and lines (including ABS/VSA)
• All uid levels and condition of uids
• Exhaust system #
•F uel lines and connection s#
*2:If you drive in dusty conditions, replace the air cleaner element every 15,000 miles (24,000 km).*3:If you drive primarily in urban areas that have high concentrations of soot in the air from industryand diesel-powered vehicles, replace the dust and pollen lter every 15,000 miles (24,000 km).*4:Driving in mountainous areas at very low vehicle speeds results in higher transmission
temperatures. This requires transmission uid changes more frequently than recommended by
the Maintenance Minder. If you regularly drive your vehicle under these conditions, have the
transmission uid changed every 25,000 miles (40,000 km).
CODEMaintenance Sub Items
1 
Rotate tires
2
Replace air cleaner element *2
 Replace dust and pollen lter *3
 Inspect drive belt
3 
Replace transmission uid *4
4
Replace spark plug s
 Inspect valve clearance
5 
Replace engine coolant
7Replace brake uid*5
*5:If a Maintenance Minder indicator does not appear more than 36 months after the display for item 7 is reset, change the brake uid every 3 years.
In addition: •  Inspect idle speed every 160,000 miles (256,000 km).
•  Adjust the valves during services A, B, 1, 2, or 3 if they are noisy.

140 || 141
MAINTENANCE
MAINTENANCE
Tire Information
To safely operate your vehicle, your tires must be of the proper type and size, in good condition with adequate tread, and properly inated.
Inflation Guidelines
•  Properly inated tires provide the best combination of handling, tread life, and
comfort. Refer to the driver’s doorjamb label or the specications (see page 147) for the specied pressure.
•  Underinated tires wear unevenly, adversely affect handling and fuel economy,
and are more likely to fail from overheating.
•  Overinated tires make your vehicle ride harshly, are more prone to road hazards,
and wear unevenly.
•  Every day before you drive, look at each of the tires. If one looks lower than the
others, check the pressure with a tire gauge.
•  Measure the air pressure when tires are cold. This means the vehicle has been
parked for at least 3 hours, or driven less than 1 mile (1.6 km). If necessary, add or release air until the specied pressure is reached, and then calibrate the system
(see page 118). If checked when hot, tire pressure can be as much as 4–6 psi (30–40 kPa, 0.3–0.5 kgf/cm 2
) higher than checked when cold.
•  At least once a month or before long trips, use a gauge to measure the pressure in
all tires, including the spare. Even tires in good condition can lose 1–2 psi (10–20 kPa, 0.1–0.2 kgf/cm 2
) per month.
Inspection Guidelines
Every time you inate the tires, check for the following: •  Any damage to tires, including bumps, bulges, cuts, splits, or cracks in the side or
tread. Remove any foreign objects and inspect for air leaks. Replace tires if you see fabric or cord.
•  Uneven or excessive tread wear. Have a dealer check the wheel alignment.
•  Cracks or other damage around the valve stems.
Wear Indicators
The groove where the wear indicator is located is 1/16 inch (1.6 mm) shallower than elsewhere on the tire. If the tread has worn so low that the indicator is exposed, replace the tire. Worn out tires have poor
traction on wet roads.
Example of a wear indicator mark
Tire and Loading Information Label
The label attached to the driver’s doorjamb provides necessary tire and loading information.
Tire and Wheel Replacement
Replace your tires with radials of the same size, load range, speed rating, and
maximum cold tire pressure rating (as shown on the tire’s sidewall). Using tires of a
different size or construction can cause certain vehicle systems to work incorrectly.
It is best to replace all four tires at the same time. If that isn’t possible, replace the front or rear tires in pairs.
If you change or replace a wheel, make sure that the wheel’s specications match those of the original wheels. Using tires that are excessively worn or improperly inated can cause a crash in which you can be seriously hurt or killed.
Follow all instructions in this owner’s manual regarding tire ination and maintenance
.
WARNING
Original tire sizesNumber of people your vehicle can carryProper cold tire pressureTotal weight your
vehicle can carry (do not exceed)
Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.
Always use the size and type of tires recommended in the Owner’s Manual.
WARNING

146 || 147
SPECIFICATIONS
MAINTENANCE
Testing of Readiness Codes
Your vehicle has “readiness codes” as part of the onboard self-diagnostic system. Some
states refer to these codes as a test to see if your vehicle’s emissions components are
working properly. The codes may not be read if you go through the testing just after the battery has gone dead or been disconnected.
To check if they are set, turn the vehicle on without starting the engine. The malfunction
indicator lamp will come on for several seconds. If it goes off, the readiness codes are set. If it blinks ve times, the readiness codes are not set. If you are required to have your vehicle tested before the readiness codes are set, prepare the vehicle for retesting by doing the following:
1. Fill the gas tank to approximately 3/4 full.
2. Park the vehicle and leave the engine off for 6 hours or more.
3. Make sure the ambient temperature is between 40°F and 95°F (4°C and 35°C).4. Start the engine without touching the accelerator pedal, and let it idle for 20 seconds.
5. Keep the vehicle in Park (P) or Neutral for manual transmission. Increase the engine speed to 2,000 rpm, and hold it there for about 3 minutes.
6. Let the engine idle with your foot off the accelerator for 20 seconds.
7. Select a nearby, lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway with
the vehicle in Drive (D) or 5th gear. Do not use cruise control. When trafc allows,
drive for 90 seconds without using the accelerator pedal. (Vehicle speed may vary
slightly; this is OK.) If you cannot do this for a continuous 90 seconds because of
trafc conditions, drive for at least 30 seconds, then repeat two more times (for a total of 90 seconds).
8. Drive in city/suburban trafc for at least 10 minutes. When trafc conditions allow, let the vehicle coast for several seconds without using the accelerator pedal or the brake pedal.
9. Park the vehicle and leave the engine off for 30 minutes.
The readiness codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
If a testing facility determines that the readiness codes are not set, you may be
requested to return at a later date to complete the test, or see your dealer.SPECIFICATIONS 1.5-L engine models
Vehicle
ModelHonda Civic 2-Doo r
No. of Passengers :
Fron t2
Rear 3
Tota l5
Weights:Gross Vehicle Weight Rating U.S.: 3,902 lbs (1,770 kg )
Canada: 1,770 kg
Gross Axle Weight
Rating (Front )U.S.: 2,105 lbs (955 kg )
Canada: 955 kg
Gross Axle Weight
Rating (Rear)U.S.: 1,808 lbs (820 kg )
Canada: 820 kg
Light Bulbs
*1:Models with halogen headlights*2: Models with LED headlights
Headlights (Low Beam)55W (H11) *1
LE D*2
Headlights (High Beam )60W (HB3)
*1
LE D*2
Fog Lights35W (H8
)
Parking/Da ytime Running Light sLED
Front Side Marker Lights3W
Front Turn Signal Lights 21W (Amber
)*1
LE D*2
Side Turn Signal Lights

(on Door Mirrors) *LE
D
Brake Light s2 1W
Rear Turn Signal Lights21W (Amber)
Rear Side Marker Lights LED
Back-Up Lights16 W
DEL
sthgilliaT
High-M ount Brake LightRear License Plate Light LEDTrunk Light5W
In terior Lights
Map Lights8 W
Ceiling Ligh t8 W
DEL
Engine and Fuel
Engine FuelDisplacemen t91.26 cu-in (1,496 cm 3
)
Spark Plug sN GKILZKAR8H8S
Fuel: TypeUnleaded gasoline, Pump octane number of 87 or highe r
Fuel Tank Capacity 12.39 US gal (46.9 ℓ)
Fluids
Air ConditioningRefrigerant TypeHFO-1234yf (R-1234yf)
Charge Quantity 13.2 – 15.0 oz (375 – 425 g)
Lubricant TypeRL85HM (POE)
Quantity 2.7 – 3.6 oz (77 – 103 g)
Washer Fluid
Tank CapacityU.S.: 2.6 US qt (2.5 ℓ) Canada: 4.8 US qt (4.5 ℓ)
Brake Fluid
Continuously Variable Transmission Fluid
SpeciedHonda Heavy Duty Brake Fluid DOT 3
SpeciedHonda HCF-2 Transmission Flui d
Capacity Change 3.9 US qt (3.7 ℓ)
Engine Oil
Engine Coolan
t
Recommended·Genuine Honda Motor Oil 0W-20 ·API Premium-grade 0W-20 detergent oi l
Capacity Change
3.4 US qt (3.2 ℓ)
Change including
lte r 3.7 US qt (3.5 ℓ)
SpeciedHonda Long Life Anti
freeze/Coolant Type 2
Ratio 50/50 with distilled wate r
Capacity1.34 US gal (5.09 ℓ)

(change including the remaining
0.2 US gal (0.75 ℓ) in the reserve tank )
Tires
RegularSize215/50R17 91HPressure psi (kPa [kgf/cm 2
])32 (220 [2.2] )
Compact Spar e Size
T125/80D16 97M
Pressure psi (kPa [kgf/cm 2
]) 60 (420 [4.2]
)
Wheel SizeRegular17 x 7JCompact Spar e16 x 4T

148 || 149
CUSTOMER INFORMATION
SPECIFICATIONS
2.0-L engine models
Vehicle
Model Honda Civic 2-Door
No. of Passengers :
Fron t2
Rear 3
Tota l5
Weights:Gross Vehicle Weight Rating U.S.: 3,737 lbs (1,695 kg )
Canada: 1,695 kg
Gross Axle Weight
Rating (Front )U.S.: 1,984 lbs (900 kg )
Canada: 900 kg
Gross Axle Weight
Rating (Rear)U.S.: 1,786 lbs (810 kg )
Canada: 810 kg
Light Bulbs
Headlights (Low Beam)55W (H11)Headlights (High Beam )60W (HB3)Parking/Daytime Running Light sLED
Front Side Marker Ligh t
Front Turn Signal Lights21W (Amber )
Brake Lights 21W
Rear Turn Signal Lights21W (Amber)
Rear Side Marker Lights LED
Back-Up Lights16W
DEL
sthgilliaT
High-M ount Brake LightRear License Plate Light LEDTrunk Light5W
In terior Lights
Map Light s8W
Ceiling Ligh t8 W
3W
DEL
Engine and Fuel
Engine FuelDisplacemen t121.76 cu-in (1,996 cm 3
)
Spark Plug s NG
K DILKAR7H11GS DILKAR7G11GS
DENSO DXE22HQR-D11 S
Fuel: TypeUnleaded gasoline, Pump octane number of 87 or highe r
Fuel Tank Capacity 12.39 US gal (46.9 ℓ)
Fluids
Air Conditioning *Refrigerant TypeHFO-1234yf (R-1234yf)
Charge Quantity 13.2 – 15.0 oz (375 – 425 g)
Lubricant TypeRL85HM (POE)
Quantity 2.7 – 3.6 oz (77 – 103 g)
Washer Fluid
Tank CapacityU.S.: 2.6 US qt (2.5 ℓ) Canada: 4.8 US qt (4.5 ℓ)
Brake/Clutch Fluid
Continuously Variable Transmission Fluid Manual Transmission Fluid
SpeciedHonda Heavy Duty Brake Fluid DOT 3
SpeciedHonda HCF-2 Transmission Flui d
Capacity Change 3.7 US qt (3.5 ℓ)
SpeciedHonda Manual Transmission Fluid (MTF )
Capacity Change 2.0 US qt (1.9 ℓ)
Engine Oil
Engine Coolan
t
Recommended·Genuine Honda Motor Oil 0W-20 ·API Premium-grade 0W-20 detergent oi l
Capacity Change
4.2 US qt (4.0 ℓ)
Change including
lte r 4.4 US qt (4.2 ℓ)
SpeciedHonda Long Life Anti
freeze/Coolant Type 2
Ratio 50/50 with distilled wate r
Capacity1.4 US gal (5.30 ℓ)
(change including the remaining
0.2 US gal (0.75 ℓ) in the reserve tank )
*
*
*
Tires
RegularSize215/55R16 93HPressure psi (kPa [kgf/cm 2
])32 (220 [2.2] )
Compact Spar e* Size
T125/80D16 97M
Pressure psi (kPa [kgf/cm 2
]) 60 (420 [4.2]
)
Wheel SizeRegular16 x 7JCompact Spar e16 x 4T
*if equipped
CUSTOMER INFORMATION
*if equipped
Learn about information specic to you as a Honda customer and how to get help.
Frequently Asked Questions/Troubleshooting
Below are some frequently asked questions and troubleshooting items that you may have about the vehicle. Q:
How do I set the vehicle clock?
A: For vehicles without navigation, see page 51. For vehicles with navigation, the
time is automatically set using GPS signals.Q: Why doesn’t the vehicle start when I press the ENGINE START/STOP button?*
A: The brake pedal must be pressed to start the engine.
Q: What is the AUTO* setting on my headlight lever?
A: When in the AUTO position, the vehicle’s exterior lights will automatically turn
on or off depending on the ambient lighting.Q: Why won’t the driver’s door unlock when I grab the door handle, even though 
  the keyless access remote is within range?* A: If you pull the handle too quickly, the system may not have time to conrm the
door is unlocked. Wait to hear a beep to conrm the door is unlocked. If you are
wearing gloves, the system may be slow to respond. Q: After my battery was disconnected or went dead, the audio system is asking for 
  a code. Where do I ind this? A: In most cases, you do not need to enter a code. Turn on the vehicle and the
audio system, and press and hold the power button until the system reactivates. Q: Why can’t I operate Pandora through the audio system?*
A: Audio may be streaming through Bluetooth Audio. Make sure Pandora mode
is selected and the phone cable is properly connected to the USB adapter
cable (if using). Some phones may prompt you to “Allow” a connection. Q: Is my phone compatible with  Bluetooth features?
A: Visit handsfreelink.com (U.S.) or www.handsfreelink.ca (Canada) to
check phone compatibility for Bluetooth Audio, Bluetooth HandsFreeLink,
and SMS text messaging.Q: Every time I press the Talk button, the system gives me voice prompts. Can I turn 
  these off?* A: From the Home screen, select SETTINGS. Select System, then select Voice
Prompt. Select Off.