2016 HONDA ACCORD COUPE belt

14 || 15
SAFETYSAFETY
Child Safety
Each year, many children are injured or killed in vehicle crashes because they are 
either unrestrained or not properly restrained. In fact, vehicle collisions are the 
number one cause of death of children ages 12 and under.
The National Highway Traffic Safety Administration and Transport Canada
recommend that all children ages 12 and under be properly restrained in a rear seat. 
Some states or provinces/territories have laws restricting where children may  ride. 
To reduce the number of child deaths and injuries, every state, Canadian province 
and territory requires that infants and children be properly restrained when they ride 
in a vehicle.
Protecting Child Passengers
• An inflating front or side airbag can injure or kill a child sitting in the front seat.
• A child in the front seat is more likely to interfere with the driver’s ability to 
safely control the vehicle.
• Statistics show that children of all sizes and ages are safer when they are 
properly restrained in a rear seat.
• Any child who is too small to wear a seat belt correctly must be restrained in an 
approved child seat that is properly secured to the vehicle using either\
the lap
belt portion of the lap/shoulder belt or the lower anchors of the LATCH system.
• Never hold a child on your lap because it is impossible to protect them in the 
event of a collision.
• Never put a seat belt over yourself and a child. During a crash, the belt would 
likely press deep into the child and cause serious or fatal injuries.
• Never let two children use the same seat belt. Both children could be very 
seriously injured in a crash.
• Do not allow children to operate the doors, windows, or seat adjusters.
• Do not leave children in the vehicle unattended, especially in hot weath\
er when
the inside of the vehicle can get hot enough to kill them. They could al\
so activate
vehicle controls, causing it to move unexpectedly.
Protecting Infants
An infant must be properly restrained in a rear-facing, reclining child seat until the 
infant reaches the seat maker’s weight or height limit for the seat, and the infant
is at least one year old. Many experts recommend use of a rear-facing seat for
a child up to two years old if the child’s height and weight are appropriate for a
rear-facing seat.
Child seats must be placed and secured in a rear 
seating position. rear-facing child seats should
never be installed in a forward-facing position.
When properly installed, a rear-facing child seat may prevent the driver or a front 
passenger from moving their seat all the way back, or from locking their seat-back 
in the desired position. If this occurs, we recommend that you install the child 
seat directly behind the front passenger’s seat, move the seat as far forward as 
needed, and leave it unoccupied. or, you may wish to get a smaller rear-facing
child seat.
Allowing a child to play with a seat belt or wrap one around their neck can 
result in serious injury or death.
Instruct children not to play with any seat belt and make sure any unused 
seat belt a child can reach is buckled, fully retracted, and locked.
WARNING
Children who are unrestrained or improperly restrained can be seriously 
injured or killed in a crash.
Any child too small for a seat belt should be properly restrained in a child 
seat. A larger child should be properly restrained with a seat belt, using a 
booster seat if necessary.
WARNING
Placing a rear-facing child seat in the front seat can result in serious injury or
death during a crash.
Always place a rear-facing child seat in the rear seat, not the front.
WARNING

16 || 17
SAFETYSAFETY
Protecting Smaller Children
If a child is at least one year old and within the weight range indicated by the child 
seat manufacturer, the child should be properly restrained in a firmly secured 
forward-facing child seat.
We strongly recommend placing a forward-facing 
child seat in a rear seating position.
Placing a forward-facing child seat in the front seat
can be hazardous,  even with advanced  front airbags 
that automatically turn the passenger’s front airbag 
off. A rear seat is the safest place for a child.
Selecting a Child Seat
Most child seats are LATCH-compatible (Lower Anchors and Tethers for CHildren). 
Some have a rigid-type connector, while others have a flexible-type connector. 
Both are equally easy to use. Some existing and previously owned child seats can 
only be installed using the seat belt. Whichever type you choose, follow the child 
seat manufacturer’s use and care instructions as well as the instructions in this
manual. Proper installation is key to maximizing your child’s safety.
In seating positions and vehicles not equipped with LATCH, a LATCH-compatible 
child seat can be installed using the seat belt and a top tether for added security. 
This is because all child seats are required to be designed so that they can be 
secured with a lap belt or the lap part of a lap/shoulder belt. In addition,  the 
child seat manufacturer may advise that a seat belt be used to attach a LATCH-
compatible seat once a child reaches a specified weight. Please read the child 
seat owner’s manual for proper installation instructions.
Important considerations when selecting a child seat
Make sure the child seat meets the following three requirements:
• The child seat is the correct type and size for the child.
• The child seat is the correct type for the seating position.
• The child seat is compliant with Federal Motor vehicle Safety Standard 213 or
Canadian Motor vehicle Safety Standard 213.
Installing a LATCH-Compatible Child Seat
A LATCH-compatible child seat can be installed in either of the two outer rear 
seats. A child seat is attached to the lower anchors with either the rigid or  flexible 
type of connectors.
1. Locate the lower anchors under the marks.
2. Place the child seat on the vehicle seat, then
attach the child seat to the lower anchors
according to the instructions that came with the
child seat. Make sure that the lower anchors
are not obstructed by the seat belt or any other 
object.
3. Open the tether anchor cover behind the head 
restraint.
4. raise the head restraint to its highest position,
then route the tether strap between the head 
restraint legs, and secure the tether strap hook
onto the anchor.
5. Tighten the tether strap according to the seat
maker’s instructions.
6. Make sure the child seat is firmly secured by 
rocking it forward and back and side to side; little 
movement should be felt.
7. Make sure any unused seat belt that a child 
can reach is buckled, the lockable retractor 
is activated, and the belt is fully retracted and 
locked.
Placing a forward-facing child seat in the front seat can result in seri\
ous
injury or death if the front airbag inflates.
If you must place a forward-facing child seat in front, move the vehicle seat 
as far back as possible, and properly restrain the child.
WARNING
Anchor
Tether
strap
hoo k
Marks
Rigid typ e
Lower anchors
Flexible type

18 || 19
SAFETYSAFETY
Installing a Child Seat with a Lap/Shoulder Seat Belt
1. Place the child seat on the vehicle seat.
2. Route the seat belt through the child seat 
according to the seat manufacturer’s
instructions, and insert the latch plate into the
buckle. Insert the latch plate fully until it clicks.
3. Slowly pull the shoulder part of the belt all the 
way out until it stops. This activates the lockable 
retractor.
4. Let the seat belt completely wind up into the 
retractor, then try to pull it out to make sure the
retractor is locked. If you are able to pull the 
shoulder belt out, the lockable retractor is not 
activated. Pull the seat belt all the way out, and 
repeat steps 3 – 4.
5. Grab the shoulder part of the seat belt near the 
buckle, and pull up to remove any slack from 
the lap part of the belt. When doing this, place 
your weight on the child seat and push it into the
vehicle seat.
6. Make sure the child seat is firmly secured by 
rocking it forward and back and side to side; little 
movement should be felt.
7. Make sure any unused seat belt that a child 
can reach is buckled, the lockable retractor 
is activated, and the belt is fully retracted and 
locked.
 To deactivate a lockable retractor, release the buckle and allow the seat belt to 
wind up all the way.
Adding Security with a Tether
A tether anchorage point is provided behind each rear seating position. A child 
seat that is installed with a seat belt and comes with a tether can use the tether 
for additional security.
1. Locate the appropriate tether anchorage point
and lift the cover.
2. raise the head restraint to its highest position,
then route the tether strap through the head
restraint legs. Make sure the strap is not twisted.
3. Secure the tether strap hook onto the anchor.
4. Tighten the tether strap according to the seat
manufacturer’s instructions.
Tether anchorage points
Cove r
Anchor
Outer positi on
Tether strap
hook
Anchor
Center positionTether strap
hook
Anchor

20 || 21
SAFETYSAFETY
Protecting Larger Children
When a child is too big for a child seat, secure the child in a rear seat using the 
lap/shoulder seat belt.
Have the child sit upright and all the way back, then ensure the following:
• The child’s knees bend comfortably over the edge 
of the seat.
• The shoulder belt crosses between the child’s 
neck and arm.
• The lap part of the seat belt is as low as possible, 
touching the child’s thighs.
• The child can stay seated for the whole trip.
If a lap/shoulder belt cannot be used properly, position the child in a booster seat 
in a rear seating position. For the child’s safety, check that the child meets the
booster seat manufacturer’s recommendations.
Some U.S. states and Canadian provinces/territories require children to use a 
booster seat until they reach  a given  age or weight  (e.g., 6 years  or 60  lbs).  Be sure 
to check current laws in the state or province/territory where you intend to drive.
Safety Label Locations
Safety labels are in the locations shown. They warn you of potential hazards that 
can cause serious injury or death. Read these labels carefully.
Sun visor
U.S. models Canadian models
Radiator cap
U.S. models only
Dashboard
Allowing a child age 12 or under to sit in the front can result in injur\
y or death
if the passenger’s front airbag inflates.
If a larger child must ride in front, move the vehicle seat as far to the rear as 
possible, then have the child sit up properly and wear the seat belt properly, 
using a booster seat if needed.
WARNING

22 || 23
INSTRUMENT PANELSAFETY
INSTRUMENT PANELReporting Safety Defects
In the U.S.
If you believe that your vehicle has a defect which could cause a crash or could 
cause injury or death, you should immediately inform the National Highway Traffic
Safety Administration (NHTSA) in addition to notifying American Honda \
Motor Co.,
Inc.
If NHTSA receives similar complaints, it may open an investigation, and  if it finds 
that a safety defect exists in a group of vehicles, it may order a recal\
l and remedy
campaign. However, NHTSA cannot become involved in individual problems 
between you, your dealer, or American Honda Motor Co., Inc.
To contact NHTSA, you may call the vehicle Safety Hotline toll-free at 1-888-327-
4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator,
NHTSA, 1200 New Jersey Avenue, SE., Washington, DC 20590. You can also obtain 
other information about motor vehicle safety from http://www.safercar.gov.
In Canada
If you believe that your vehicle has a defect which could cause a crash or could 
cause injury or death, you should immediately inform Honda Canada, Inc., and you 
may also inform Transport Canada.
If Transport Canada receives similar complaints, it may open an investigation, and if 
it finds that a safety defect exists in a group of vehicles, it may le\
ad to a recall and
remedy campaign. However, Transport Canada cannot become involved in individual 
problems between you, your dealer, or Honda Canada, Inc.
To contact Transport Canada’s Defect Investigations and Recalls Division, you may 
call 1-800-333-0510. For more information on reporting safety defects or  about motor 
vehicle safety, go to http://www.tc.gc.ca/roadsafety.
Learn about the indicators, gauges, and displays related to driving the vehicle.
Indicators briefly appear with each engine start and then go out. Red and amber 
indicators are most critical. Blue and green indicators are used for gen\
eral
information.
Malfunction Indicators
These are the most critical indicators. If they come on and stay lit while driving or at 
any other time, there may be a problem. See your dealer if necessary.
Brake system
• Brake fluid is low.
• The brake system has a problem.
Press the brake pedal lightly to check pedal pressure. If normal, check 
the brake fluid level when you stop. If abnormal, take immediate action. If 
necessary, downshift the transmission to slow the vehicle using engine
braking. Have your vehicle repaired immediately.
Low oil pressure
engine oil pressure is low. Stop in a safe place. open the hood. Check the oil
level, and add oil if necessary (see page 135). If the indicator does not turn 
off, have your vehicle repaired immediately.
Charging system
The battery is not charging. Turn off all electrical items, but do not turn off 
the vehicle to prevent further battery discharge. Have your vehicle repaired 
immediately.
Supplemental Restraint System (SRS)
There is a problem with one of the airbag systems or seat belt tensioners. 
Smart Entry system*
There is a problem with the smart entry system.
U.S.
Canada
*if equipped

24 || 25
INSTRUMENT PANELINSTRUMENT PANEL
Malfunction indicator lamp (check engine light)
• The emissions control system may have a problem, or the fuel cap is loose  
or missing.
• (Blinks) A misfire in the engine’s cylinders is detected. Stop in a safe place, 
and wait for the engine to cool down.
Anti-lock Brake System (ABS)
There is a problem with the anti-lock brake system. Your vehicle still has 
normal braking ability, but no anti-lock function. 
Tire Pressure Monitoring System (TPMS)*
There is a problem with the tire pressure monitoring system, or the vehicle is  
fitted with the compact spare tire.
Light control*
There is a problem with the automatic lighting control system or low beam 
headlights.
Parking sensor system*
There is a problem with the system, or the sensor(s) are blocked.
Collision Mitigation Braking System™ (CMBS™)*
There is a problem with the system, the temperature is too high, or the 
camera is blocked.
Vehicle Stability Assist (VSA®)
There is a problem with the VSA system.
Brake system
There is a problem with the brake system.
Electric Power Steering (EPS)
There is a problem with the EPS system.
Auto High-Beam System*
There is a problem with the system, or the camera is blocked.
Starter system*
There is a problem with the starter system. If you cannot start the vehicle, 
press the brake pedal, then press and hold the ENGINE START/STOP button 
(see page 100) for 15 seconds.
Adaptive Cruise Control (ACC)*
There is a problem with the system, the temperature is too high, or the radar 
sensor is blocked.
Canada
U.S.
*if equipped
Condition Indicators
These indicators may require you to perform an action.
Parking brake
Release the parking brake before driving. You will hear a beep if you drive 
with it not fully released.
Seat belt reminder
Make sure seat belts are fastened for you and all passengers. The indicator 
blinks and beeps sound continuously if you or your front passenger has  not 
fastened your seat belts when you begin driving. If the indicator remains  on 
after seat belts are fastened, see your dealer.
Door open
A door is not closed. A beep sounds if a door is open while driving.
Low fuel
Refuel as soon as possible. If the indicator blinks, there is a problem with the 
fuel gauge. See your dealer.
Low tire pressure*
Stop in a safe place, check tire pressures, and inflate tire(s) if n\
ecessary.
The indicator also appears if your vehicle is fitted with the compact \
spare
tire. Have your regular tire repaired or replaced as soon as possible.
Washer fluid level (Canadian models)
The washer fluid is low. refill the washer fluid (see page 140).
System message*
When a condition or malfunction indicator comes on, a message also 
appears on the multi-information display. Check the display for more
information.
Maintenance Minder™*
Scheduled maintenance for your vehicle is due (see page 132).
*if equipped
Lane Keeping Assist System (LKAS)*
There is a problem with the system, the temperature is too high, or the 
camera is blocked.
Road Departure Mitigation (RDM)*
There is a problem with the system, the temperature is too high, or the 
camera is blocked.
Canada
U.S.
Canada
U.S.

42 || 43
VEHICLE CONTROLSVEHICLE CONTROLS
Folding Down the Rear Seats
The rear seat-back(s*) can be folded down to make room for large items in the 
trunk.
1. Remove the center shoulder belt from the guide.
2. Pull the release lever in the trunk to release the
lock.
3. Fold down the seat-back. Remove the rear head 
restraints if necessary (see page 41).
Push the seat-back up firmly until it locks into 
place to return it to its original position.
Make sure all items in the trunk or items extending through the opening \
into
the rear seats are properly secured. Loose items can fly forward if yo\
u have to
brake hard.
*if equipped
Guide
Center
shoulder belt
Release
lever
Adjusting the Steering Wheel
The steering wheel height and distance from your body can be adjusted so that you 
can comfortably grip the steering wheel in an appropriate driving posture.
1. Pull up the steering wheel adjustment lever.
2. Move the steering wheel up or down, and in
or out.
3. Push down the steering wheel adjustment
lever to lock the steering wheel in position.
To adjus t
To lock
Lever
Adjusting the steering wheel position while driving may cause you to los\
e
control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
WARNING
Driving Position Memory System*
You can store two driver’s seat positions into memory when the vehicle is on using
the buttons on the driver’s door.
1. Adjust the seat to your preferred position.
2. Press SeT.
3. Press and hold memory button 1 or 2. You will hear 
two beeps when the memory is set.
4. Press one of the memory buttons to recall 
previously stored positions.
Lumbar positions cannot be stored.
When you unlock and open the driver’s door with a remote transmitter, the seat 
adjusts automatically to one of the two preset positions.
Memory
button 1
Memory
button 2
SET button
*if equipped

92 || 93
DRIVINGNAVIGATION
Traffic
view traffic flow and incidents in major metro areas. You can also select traffic to
avoid. Traffic coverage is limited in Canada.
Viewing traffic
1. From the map screen, select the traffic icon.
2. Select Traffic Conditions.
3. Traffic icons are shown on the map. Select the
magnifying glass icon to display a full list of
traffic delays.
Avoiding traffic on your route
1. From the map screen, select the traffic icon.
2. Select Traffic on route.
3. Select an incident to avoid from the list.
4. Select the menu icon.
5. Select Avoid.
DRIVING
Learn about preparation for driving, as well as other features.
Before Driving
Check the following items before you begin driving.
Exterior Checks
• Make sure there are no obstructions on the windows, door mirrors, exterior 
lights, or other parts of the vehicle.
• remove any frost, snow, or ice.
• Make sure the hood is securely closed.
• Heat from the engine and exhaust can ignite flammable materials left under 
the hood, causing a fire. If you’ve parked your vehicle for an extended period, 
inspect and remove any debris that may have collected, such as dried grass 
and leaves that have fallen or have been carried in for use as a nest by a small 
animal. Also check under the hood for leftover flammable materials after you or 
someone else has performed maintenance on your vehicle.
• Make sure the tires are in good condition.
• Make sure there are no people or objects behind or around the vehicle.
Interior Checks
• Store or secure all items on board properly.
• Do not pile items higher in the cargo area than the seat-back height.
• Do not place anything in the front seat footwells. Make sure to secure t\
he floor
mats.
• If you have any animals on board, do not let them move freely around in the 
vehicle.
• Securely close and lock all doors and the trunk.
• Adjust your seating position, mirrors, and steering wheel properly.
• Make sure items placed on the floor behind the front seats cannot roll under the 
seats.
• Everyone in the vehicle must fasten their seat belt.
• Make sure that the indicators in the instrument panel come on when you s\
tart
the vehicle, and go off soon after.
If the doors are frozen shut, use warm water around the door edges to melt any 
ice. Do not try to force them open, as this can damage the rubber trim around the 
doors. When done, wipe dry to avoid further freezing.
NOTICE