2016 FIAT SCUDO bulb

139
WARNING
LIGHTS AND
MESSAGESVEHICLE
MAINTENANCETECHNICAL
SPECIFICATIONSINDEXDASHBOARD
AND CONTROLSSAFETY
DEVICESCORRECT USE
OF THE VEHICLEIN AN
EMERGENCY
ENGINE STARTING ........................................................... 140
IF A TYRE IS PUNCTURED .............................................. 141
QUICK TYRE REPAIR KIT FIX & GO ............................. 144
WHEN NEEDING TO CHANGE A BULB ................... 145
IF AN EXTERIOR BULB BURNS OUT .......................... 147
IF AN INTERIOR BULB BURNS OUT ........................... 151
IF A FUSE BLOWS ............................................................... 152
IF THE BATTERY IS FLAT ................................................. 157
TOWING THE VEHICLE ................................................... 158
I I
N N

A A
N N

E E
M M
E E
R R
G G
E E
N N
C C
Y Y
In an emergency we recommend that you call the toll-free number found on the
Warranty Booklet. You can also connect to the site www.fiat.com
to search for the nearest Fiat Dealership point
139-158 SCUDO LUM GB 07/03/14 08.47 Pagina 139

145
WARNING
LIGHTS AND
MESSAGESVEHICLE
MAINTENANCETECHNICAL
SPECIFICATIONSINDEXDASHBOARD
AND CONTROLSSAFETY
DEVICESCORRECT USE
OF THE VEHICLEIN AN
EMERGENCY
WHEN NEEDING TO
CHANGE A BULBGENERAL INSTRUCTIONS❒
When a light is not working, check that
the corresponding fuse is intact before
changing a bulb. For the location of fus-
es, refer to the paragraph “If a fuse
blows” in this section;
❒
Before changing a bulb check the con-
tacts for oxidation;
❒
Burnt bulbs must be replaced by oth-
ers of the same type and power;
❒
Always check the height of the head-
light beam after changing a bulb.
IMPORTANT The headlight inner surface
may be lightly misted over: this is not a
fault but a natural fact due to low tem-
perature and level of air humidity. It will
disappear as soon the headlights are
turned on. The presence of drops inside
the headlights means water infiltration,
therefore contact Fiat Dealership.
TYPES OF BULBS
Various types of bulbs are fitted to your
vehicle:
AAll glass bulbs: these are pressed on.
Pull to remove.BBayonet type bulbs: to remove this
type of bulb from its holder, press
the bulb and turn it counter-clock-
wise.
CTubular bulbs: release them from
their contacts to remove.
DHalogen bulbs: to remove the bulb,
release the clip holding the bulb in
place. Halogen bulbs must be han-
dled touching only the metal-
lic part. If the transparent bulb
is touched with the fingers, its
lighting intensity is reduced and life of
the bulb may be compromised. If
touched accidentally, rub the bulb with
a cloth moistened with alcohol and al-
low to dry.
Modifications or repairs to
the electrical system (elec-
tronic control units) carried out in-
correctly and without bearing the fea-
tures of the system in mind can cause
malfunctions with the risk of fire.
WARNING
Halogen bulbs contain pres-
surised gas which, if broken,
may cause small fragments of glass to
be projected outwards.
WARNING
fig. 8
F0P0216m
139-158 SCUDO LUM GB 07/03/14 08.47 Pagina 145

146WARNING
LIGHTS AND
MESSAGESVEHICLE
MAINTENANCETECHNICAL
SPECIFICATIONSINDEXDASHBOARD
AND CONTROLSSAFETY
DEVICESCORRECT USE
OF THE VEHICLEIN AN
EMERGENCY
Bulbs Ref. figure Type PowerMain beam headlightsDipped beam headlights Front sidelights Front fog lights (for versions/markets, where provided)Front direction indicators Side direction indicators Rear direction indicators Taillights Brake lights
3rdstop light (supplementary stop light):
– double-hinged rear doors
– double-hinged rear doors (high roof)/rear hatchbackReversing light Rear fog lights Number plate lights Front ceiling light with spot lightsRear ceiling lightH4
H4
W5W
H4
PY21W (amber)
WY5W (amber)
PY21W (amber)
P21/5W
P21/5W
W5W
P21W
P21W
P21W
W5W
12V5W
12V5W D
D
A
D
B
A
B
B
B
A
B
–
–
A
C
C55W
55W
5W
55W
21W
5W
21W
5W
5W
5W
21W
21W
21W
5W
5W
5W
139-158 SCUDO LUM GB 07/03/14 08.47 Pagina 146

147
WARNING
LIGHTS AND
MESSAGESVEHICLE
MAINTENANCETECHNICAL
SPECIFICATIONSINDEXDASHBOARD
AND CONTROLSSAFETY
DEVICESCORRECT USE
OF THE VEHICLEIN AN
EMERGENCY
IF AN EXTERIOR BULB
BURNS OUTFor the type of bulb and power rating, see
previous paragraph “If a bulb burns out”.FRONT LIGHT UNITS
The front light units contain dipped beams,
main beams, sidelights and direction indi-
cators bulbs.DIPPED BEAM/ MAIN BEAM
HEADLIGHTS fig. 9
To change the bulb, proceed as follows:
❒
pull the central cap Aoperating the rel-
evant tab;
❒
disconnect the electric connector;
❒
release the bulb holder catch;
❒
replace the bulb and refit the cap A,
check for proper locking.
SIDELIGHTS fig. 9
To change the bulb, proceed as follows:
❒
pull the central cap Aoperating the rel-
evant tab;
❒
remove the snap-fitted bulb holder and
disconnect the electric connector;
❒
replace the bulb and refit the cap A,
check for proper locking.
fig. 9
F0P0178m
139-158 SCUDO LUM GB 07/03/14 08.47 Pagina 147

148WARNING
LIGHTS AND
MESSAGESVEHICLE
MAINTENANCETECHNICAL
SPECIFICATIONSINDEXDASHBOARD
AND CONTROLSSAFETY
DEVICESCORRECT USE
OF THE VEHICLEIN AN
EMERGENCY
FRONT DIRECTION
INDICATORS fig. 10
To change the bulb, proceed as follows:❒
turn the bulb holder Acounterclock-
wise;
❒
after removing the bulb holder, remove
the bulb pushing it gently and turning
it counterclockwise .
❒
replace the bulb and refit the bulb hold-
er Aby turning it clockwise and lock-
ing it properly.
FRONT FOG LIGHTS fig. 11
The rear headlights contain the bulbs for
the position/stop, direction, reverse and
rear fog lights.SIDE DIRECTION INDICATORS
fig. 12
To change the bulb, proceed as follows:
❒
work on the lens Ato compress the in-
ternal catch, then pull the unit out-
wards;
❒
turn the bulb holder counterclockwise,
remove the snap-fitted bulb and replace
it;
❒
refit the bulb holder in the lens by turn-
ing it clockwise;
❒
refit the unit making sure the catch
clicks into place.
fig. 11
F0P0181m
fig. 10
F0P0179m
fig. 12
A
F0P0297m
139-158 SCUDO LUM GB 07/03/14 08.47 Pagina 148

149
WARNING
LIGHTS AND
MESSAGESVEHICLE
MAINTENANCETECHNICAL
SPECIFICATIONSINDEXDASHBOARD
AND CONTROLSSAFETY
DEVICESCORRECT USE
OF THE VEHICLEIN AN
EMERGENCY
REAR LIGHT UNITS
fig. 13
Rear light units contain taillights, brake
light, direction indicators and reversing
light bulbs.fig. 13
F0P0184m
To remove the rear headlights and replace
the bulbs, wide open (180°) the rear dou-
ble doors (see paragraph “Rear double
doors” in section “Dashboard and con-
trols”).fig. 14
F0P0185m
To replace a bulb proceed as follows:❒
Identify the bulb to be substituted;
❒
Remove the two fixing nuts Aand B
❒
From the outside, slide out the trans-
parent group;
❒
Keeping hold of the group, undo the
electrical connector;
❒
Widen the flaps and extract the lamp
holder;
❒
Extract the bulb to be substituted by
slightly pushing and turning it counter-
clockwise (“bayonet” lock) and there-
fore substitute it.
139-158 SCUDO LUM GB 07/03/14 08.47 Pagina 149

150WARNING
LIGHTS AND
MESSAGESVEHICLE
MAINTENANCETECHNICAL
SPECIFICATIONSINDEXDASHBOARD
AND CONTROLSSAFETY
DEVICESCORRECT USE
OF THE VEHICLEIN AN
EMERGENCY
THIRD BRAKE LIGHT
With boot tailgate
To change a bulb proceed as follows:❒
open the tailgate;
❒
slacken the fastening screws A;
❒
press both ends of the catch and re-
move the lens unit housing the bulbs;
❒
disconnect the electric connector;
❒
remove the snap-fitted bulb and replace
it.
With rear double doors fig. 16
To change a bulb proceed as follows:
❒
undo the fixing screws Awith a Torx™
screwdriver with a 20” head;
❒
remove the bulb holder;
❒
remove the snap-fitted bulb and replace
it.
NUMBER PLATE LIGHT
To change a bulb proceed as follows:
Versions with hinged doors fig. 17
❒
working from the inside of the vehicle,
remove the internal covering
❒
disconnect the connector by widening
the relevant flap;
❒
remove the plastic protection;
fig. 15
A
A
F0P0210m
fig. 16
A
A
F0P0211m
fig. 17
F0P0212m
fig. 18
F0P0607m
High Roof Version❒
undo the fixing screws Awith a 8”
wrench;
❒
take out the lamp holder;
❒
take out the pressure assembled bulb
and substitute it.
139-158 SCUDO LUM GB 07/03/14 08.47 Pagina 150

151
WARNING
LIGHTS AND
MESSAGESVEHICLE
MAINTENANCETECHNICAL
SPECIFICATIONSINDEXDASHBOARD
AND CONTROLSSAFETY
DEVICESCORRECT USE
OF THE VEHICLEIN AN
EMERGENCY
IF AN INTERIOR BULB
BURNS OUTFor the type of bulb and power rating, see
paragraph “When needing to change a
bulb”.
CEILING LIGHT
To replace the bulbs proceed as follows:❒
work in the points shown by the ar-
rows and remove light;
❒
replace bulbs releasing them from the
side contacts; make sure that new bulbs
are correctly clamped between contacts;
❒
secure the light into its housing locking
it properly.
fig. 19
F0P0298m
fig. 20
F0P0234m
❒
rotate lamp-holder by one fourth of
revolution anticlockwise;
❒
change the bulb.
Versions with hatchback fig. 18
❒
working from the outside of the vehi-
cle at the point indicated by the arrow
and remove transparent group A;
❒
change the bulb releasing it from the side
contacts and making sure the new bulb
is correctly fastened between the con-
tacts;
❒
refit the snap-fitted lens unit.
139-158 SCUDO LUM GB 07/03/14 08.47 Pagina 151