2016 FIAT QUBO technical specifications

DIPPED/MAIN BEAM HEADLIGHTS
To change the bulb (double filament), proceed as
follows:
❒remove the protective lid A fig. 134;
❒release the bulb holder clip;
❒remove the bulb A fig. 136 from connector B and
replace it;
❒refit the new bulb by inserting it on connector B
and then make the contour of the metallic part
mate with the grooves obtained on the headlight
parabola;
❒refit the bulb holder clip and refit the protective lid
A fig. 134 correctly.DIRECTION INDICATORS
Front
To change the bulb, proceed as follows:
❒turn the protective lid B fig. 134 anticlockwise;
❒remove the bulb A fig. 137 and replace it;
❒refit the protective lid B correctly.
fig. 136
F0T0095
fig. 137
F0T0096
147KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN
EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Side lights
To change the bulb, proceed as follows:
❒operate the lens A fig. 138 to press in the internal
catch B fig. 139, then pull the unit outwards;
❒turn the bulb holder C anti-clockwise, extract bulb
D and replace it;
❒refit the bulb holder C in the lens and turn it
clockwise;
❒refit the unit making sure that the internal catch B
clips into position.FOG LIGHTS
(for versions/markets, where provided)
IMPORTANT Contact Fiat Dealership to replace the
front fog lights.
fig. 138
F0T0097
fig. 139
F0T0098
148KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

REAR LIGHT CLUSTERS
The rear light clusters contain taillight, brake light,
direction indicator and reverse/rear fog light bulbs.
To access the light clusters, proceed as follows:
❒open the rear swing doors;
❒loosen the screws A fig. 140 so as to access the
light cluster B fig. 141;
❒remove the connector C fig. 141.
The bulbs are arranged inside the light cluster fig. 142
and fig. 143 as follows:A
Brake lights
BDirection indicatorsC
Reverse lights
D
Tail lights/rear fog lightfig. 140
F0T0099
fig. 141
F0T0100
fig. 143
F0T0102
149KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN
EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Pull the 5 tabs E fig. 142 outwards to access the
bulbs.THIRD BRAKE LIGHTS
Tailgate versions
To replace the bulbs, proceed as follows fig. 144 -
fig. 145:
fig. 142
F0T0101
fig. 144
F0T0212
AC
AB
fig. 145
F0T0443
150KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
❒open the tailgate and loosen the two retaining
screws A;

❒disconnect the electrical connector B;
❒release the retainer tab C and open the bulb
holder assembly;
❒extract the snap-fitted bulb and replace it.NUMBER PLATE LIGHTS
Proceed as follows to replace the bulbs A fig. 146:
❒operate the holding tabs at the points indicated by
the arrows, and remove the bulb holder;
❒turn the bulb holder B fig. 147 anticlockwise and
then remove the bulb C.
fig. 146
F0T0104
fig. 147
F0T0105
151KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN
EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
❒open the tailgate and loosen the two retaining
screws A;

CHANGING AN INTERIOR BULBFor the type of bulb and corresponding power rating,
see the paragraph "Changing a bulb".
FRONT CEILING LIGHT
Ceiling light with movable lens
To change the bulbs, proceed as follows:
❒extract the ceiling light A fig. 148 by operating in
the points shown by the arrows;❒open the lid B fig. 149 as shown;
❒remove bulb C fig. 149 by releasing it from the side
contacts, then insert the new bulb and make sure
it is correctly clamped between these contacts;
❒close the lid and secure the ceiling light into its
housing, making sure it locks properly into place.
fig. 148
F0T0106
fig. 149
F0T0458
152KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Roof light with spot lights
(for versions/markets, where provided)
To change the bulbs, proceed as follows:
❒operate in the points shown by the arrows and
remove ceiling light A fig. 150;
❒open the protective lid B fig. 151;
❒replace the bulbs C releasing them from the side
contacts and making sure that the new bulbs are
correctly secured between the contacts;
❒re-close the lid B fig. 151 and secure light A
fig. 150 into its housing locking it properly.REAR CEILING LIGHT
To change the bulb, proceed as follows:
❒extract the ceiling light A fig. 152 by operating in
the points shown by the arrows;
fig. 150
F0T0143
fig. 151
F0T0144
fig. 152
F0T0107
153KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN
EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

❒open the lid B fig. 153 as shown;
❒remove bulb C fig. 153 by releasing it from the side
contacts, then insert the new bulb and make sure
it is correctly clamped between these contacts;
❒close the lid B and secure the ceiling light into its
housing, making sure it locks properly into place.
REMOVABLE CEILING LIGHT
(for versions/markets, where provided)
To change the bulb, proceed as follows:
❒press button A fig. 154 and extract the removable
ceiling light B;
❒extract the ceiling light by operating in the points
shown by the arrows;❒change the bulb C fig. 155 by releasing it from the
side contacts and making sure the new bulb is
correctly fastened between these contacts;
fig. 153
F0T0458
A
UT
O
fig. 154
F0T0108
A
U
T
O
fig. 155
F0T0109
154KNOW YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX