2016 FIAT 500 ABARTH bulb

Your vehicle has a simple ignition actuated test, which
you can use prior to going to the test station. To check if
your vehicle’s OBD II system is ready, you must do the
following:
1. Cycle the ignition switch to the ON position, but donot crank or start the engine.
NOTE: If you crank or start the engine, you will have to
start this test over.
2. As soon as you cycle the ignition switch to the ON position, you will see the “Malfunction Indicator Light
(MIL)” symbol come on as part of a normal bulb
check.
3. Approximately 15 seconds later, one of two things will happen:
• The MIL will flash for about 10 seconds and then
return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your
vehicle’s OBD II system is
not readyand you should
not proceed to the I/M station.
• The MIL will not flash at all and will remain fully
illuminated until you place the ignition in the off
position or start the engine. This means that your
vehicle’s OBD II system is readyand you can proceed
to the I/M station.
If your OBD II system is not ready,you should see your
authorized dealer or repair facility. If your vehicle was
recently serviced or had a battery failure or replacement,
you may need to do nothing more than drive your
vehicle as you normally would in order for your OBD II
system to update. A recheck with the above test routine
may then indicate that the system is now ready.
Regardless of whether your vehicle’s OBD II system is
ready or not, if the MIL is illuminated during normal
vehicle operation you should have your vehicle serviced
346 MAINTAINING YOUR VEHICLE

REPLACEMENT BULBS
Interior Bulbs
Bulb Number
Overhead Lamp C5W
Courtesy Lamp W5W
Exterior Bulbs
Bulb Number
Front Low and High Beam Headlamp HIR2LL
Front Parking/Daytime Running Lamps W21/5W
Front Fog Lamps H11LL
Front Side Marker Lamps W3W
Front Turn Signal Lamps WY21W
Side Direction Lamps WY5W
Rear Turn Signal Lamps PY21W
Rear Side Marker Lamps W3W
388 MAINTAINING YOUR VEHICLE

Bulb Number
Rear Tail and Stop Lamps P21/5W
Rear Backup Lamps W16W
Center High Mounted Stop Lamp W5W
License Plate Lamps LED (See Authorized dealer)
NOTE: Numbers refer to commercial bulb types that can be purchased from your authorized dealer.
If a bulb needs to be replaced, visit your authorized dealer or refer to the applicable Service Manual.
BULB REPLACEMENT
NOTE: Lens fogging can occur under certain atmo-
spheric conditions. This will usually clear as atmospheric
conditions change to allow the condensation to change
back into a vapor. Turning the lamps on will usually
accelerate the clearing process.
Headlamps Low Beam And High Beam
1. Remove the plastic cap from the back of the headlamp housing.
2. Rotate the bulb counter-clockwise.
3. Remove the bulb and replace as needed.
4. Install the bulb and rotate clockwise to lock in place.
5. Reinstall the plastic cap.7
MAINTAINING YOUR VEHICLE 389

Front Turn Signal, Parking And Daytime Running
Lamps
1. Turn the steering wheel completely to the left or right.
2. Open the wheel housing access door.3. Remove the plastic cap from the back of the lamp
housing.
4. Rotate bulb/socket counter-clockwise.
5. Remove the bulb and replace as needed.
6. Install the bulb into socket, and rotate bulb/socket clockwise into lamp locking it in place.
7. Reinstall the plastic cap.
Front Fog Lamps
To replace the front fog lights, see your authorized dealer.
Front/Rear Side Marker Lamps
1. Remove portion of the wheel liner to allow hand access to side marker lamp.
2. Rotate the bulb socket counterclockwise, and remove the bulb and socket assembly from the housing.
Wheel Housing Access Door
390 MAINTAINING YOUR VEHICLE

3. Pull the bulb from the socket and insert the replace-ment bulb.
4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place.
5. Reinstall the wheel liner.
Rear Tail, Stop, Backup And Turn Signal Lamps
1. Open the liftgate.
2. Remove the two screws and remove the tail lamp assembly.
Tail Lamp Assembly Screws
7
MAINTAINING YOUR VEHICLE 391

3. Remove four screws and separate the backplate fromthe lamp housing.
4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise.
5. Remove the backup lamp bulb by pulling straight out.
6. Replace lamps as required and reinstall lamp.
Center High Mounted Stop Lamp (CHMSL)
1. Remove the two guard caps and the two fastening screws.
2. Remove the center high mounted stop lamp assembly.
3. Disconnect the electric connector. 4. Press the retaining device and open the bulb holder.
5. Remove the snap-fitted bulb to be replaced and re-
place it.
6. Close the back cap locking it properly.
7. Reinstall the two fastening screws and reinstall the guard caps.
392 MAINTAINING YOUR VEHICLE

Audio Systems (Radio).....................194
Automatic Dimming Mirror ...................88
Automatic Door Locks ......................23
Automatic Temperature Control (ATC) ..........216
Automatic Transaxle ........................11
Automatic Transmission ..............235, 371, 373
Adding Fluid ...................... .372, 373
Fluid And Filter Changes ..................373
Fluid Change ......................... .373
Fluid Level Check ...................... .372
Fluid Type ........................... .396
Gear Ranges .......................... .238
Special Additives ...................... .372
Autostick .............................. .243
Battery ............................ .155, 352
Charging System Light ...................155
Jump Starting ......................... .331
Keyless Transmitter Replacement (RKE) ........19Belts, Seat
...............................77
Body Mechanism Lubrication .................357
B-Pillar Location ......................... .269
Brake Assist System ...................... .255
Brake Fluid ......................... .394, 396
Brake, Parking .......................... .249
Brakes ................................ .368
Brake System ........................ .253, 368
Anti-Lock (ABS) ....................... .254
Master Cylinder ....................... .369
Parking ............................. .249
Warning Light ........................ .153
Brake/Transmission Interlock .................236
Bulb Replacement ..................... .388, 389
Bulbs, Light .......................... .79, 388
Capacities, Antifreeze (Engine Coolant) ..........393
Capacities, Fluid ......................... .393
10
INDEX 415

Jack Location........................... .324
Jack Operation ....................... .323, 325
Jump Starting ........................... .331
Key Fob Disarm The Alarm .......................15
Key-In Reminder ..........................13
Key, Replacement ..........................14
Keys ...................................11
Key, Sentry (Immobilizer) ....................13
Lane Change Assist ....................... .103
Lap/Shoulder Belts .........................30
Latches .................................79
Hood ................................98
Lead Free Gasoline ....................... .297
Leaks, Fluid ..............................79
Life Of Tires ............................ .284
Liftgate (Sedan) ...........................25 Light Bulbs
.......................... .79, 388
Lights .............................. .79, 100
AirBag .........................52, 77, 150
Brake Assist Warning ....................261
Brake Warning ........................ .153
Bulb Replacement ...................... .389
Cruise ........................... .175, 177
Engine Temperature Warning ...............158
Exterior ...............................79
Fog ................................ .168
High Beam ........................... .101
Malfunction Indicator (Check Engine) .........166
Park ............................ .101, 174
Seat Belt Reminder ..................... .151
Service .............................. .389
Tire Pressure Monitoring (TPMS) ............161
Traction Control ....................... .261
Turn Signal ..................... .79, 102, 174
Warning (Instrument Cluster Description) . . .158, 174
10
INDEX 421