2016 DODGE JOURNEY homelink

ELECTRONIC SPEED CONTROL — IF
EQUIPPED .......................... .238
▫ To Activate ......................... .239
▫ To Set A Desired Speed .................239
▫ To Deactivate ....................... .240
▫ To Resume Speed .....................240
▫ To Vary The Speed Setting ...............240
▫ To Accelerate For Passing ...............241
 PARKSENSE REAR PARK ASSIST — IF
EQUIPPED .......................... .242
▫ ParkSense Sensors .....................243
▫ ParkSense Warning Display ..............243
▫ ParkSense Display .....................243
▫ Enabling And Disabling ParkSense .........247▫
Service The ParkSense Rear Park Assist
System ............................ .247
▫ Cleaning The ParkSense System ...........248
▫ ParkSense System Usage Precautions ........248
 PARKVIEW REAR BACK UP CAMERA — IF
EQUIPPED .......................... .250
 OVERHEAD CONSOLE ..................252
▫ Courtesy/Reading Lights ................253
▫ Sunglasses Storage ....................254
▫ Interior Observation Mirror ..............254
▫ Power Sunroof Switch — If Equipped .......255
 GARAGE DOOR OPENER — IF EQUIPPED . . .255
▫ Before You Begin Programming HomeLink . . .257
▫ Programming A Rolling Code .............257
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

▫Programming A Non-Rolling Code .........259
▫ Canadian/Gate Operator Programming ......261
▫ Using HomeLink .....................262
▫ Security ........................... .262
▫ Troubleshooting Tips ...................263
▫ General Information ....................264
 POWER SUNROOF — IF EQUIPPED ........264
▫ Opening Sunroof — Express ..............266
▫ Opening Sunroof — Manual Mode .........266
▫ Closing Sunroof — Express ...............266
▫ Closing Sunroof — Manual Mode ..........266
▫ Pinch Protect Feature ...................266
▫ Venting Sunroof — Express ..............267▫
Sunshade Operation ....................267
▫ Wind Buffeting ...................... .267
▫ Sunroof Maintenance ...................267
▫ Ignition Off Operation ..................268
 POWER OUTLETS .....................268
 POWER INVERTER — IF EQUIPPED ........272
▫ Power Inverter Operation ................274
 CUPHOLDERS ....................... .274
 STORAGE ........................... .276
▫ Glove Compartment ...................276
▫ Floor Console Storage ..................277
▫ Center Console Storage .................277
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117

Power Sunroof Switch — If Equipped
Refer to “Power Sunroof” in “Understanding the Fea-
tures Of Your Vehicle” for further information.
GARAGE DOOR OPENER — IF EQUIPPED
HomeLink replaces up to three remote controls (hand-
held transmitters) that operate devices such as garage
door openers, motorized gates, lighting or home security
systems. The HomeLink unit operates off your vehicle’s
battery.
The HomeLink buttons, located on either the overhead
console, headliner or sunvisor, designate the three differ-
ent HomeLink channels. The HomeLink indicator is
located above the center button.
Observation Mirror
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255

NOTE:HomeLink is disabled when the Vehicle Security
Alarm is active.
HomeLink Buttons/Overhead ConsolesHomeLink Buttons/Sunvisor/Headliner
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Before You Begin Programming HomeLink
Be sure that your vehicle is parked outside of the garage
before you begin programming.
For more efficient programming and accurate transmis-
sion of the radio-frequency signal it is recommended that
a new battery be placed in the hand-held transmitter of
the device that is being programmed to the HomeLink
system.
To erase the channels place the ignition in the ON/RUN
position and push and hold the two outside HomeLink
buttons (I and III) for up 20 seconds or until the red
indicator flashes.NOTE:
•
Erasing all channels should only be performed when
programming HomeLink for the first time. Do not
erase channels when programming additional buttons.
• If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.
Programming A Rolling Code
For programming garage door openers that were manu-
factured after 1995. These garage door openers can be
identified by the “LEARN” or “TRAIN” button located
where the hanging antenna is attached to the garage door
opener. It is NOT the button that is normally used to
open and close the door. The name and color of the
button may vary by manufacturer.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257

1. Place the ignition in the ON/RUN position.2. Place the hand-held transmitter 1 to 3 inches (3 to 8
cm) away from the HomeLink button you wish to
program while keeping the HomeLink indicator light
in view.
3. Push and hold the HomeLink button you want to program while you push and hold the hand-held
transmitter button.
4. Continue to hold both buttons and observe the indi- cator light. The HomeLink indicator will flash slowly
and then rapidly after HomeLink has received the
frequency signal from the hand-held transmitter. Re-
lease both buttons after the indicator light changes
from slow to rapid.
5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can
usually be found where the hanging antenna wire is
attached to the garage door opener/device motor.
Training The Garage Door Opener
1 — Door Opener
2 — Training Button 258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Firmly push and release the “LEARN” or “TRAIN-
ING” button. On some garage door openers/devices
there may be a light that blinks when the garage door
opener/device is in the LEARN/TRAIN mode.
NOTE: You have 30 seconds in which to initiate the next
step after the LEARN button has been pushed.
6. Return to the vehicle and push the programmed HomeLink button twice (holding the button for two
seconds each time). If the garage door opener/device
activates, programming is complete.
NOTE: If the garage door opener/device does not acti-
vate, push the button a third time (for two seconds) to
complete the training.
To program the remaining two HomeLink buttons, repeat
each step for each remaining button. DO NOT erase the
channels.Reprogramming A Single HomeLink Button
(Rolling Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Push and hold the desired HomeLink button until the indicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button proceed with “Program-
ming A Rolling Code” step 2 and follow all remaining
steps.
Programming A Non-Rolling Code
For programming Garage Door Openers manufactured
before 1995.
1. Place the ignition in the ON/RUN position.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259

2. Place the hand-held transmitter 1 to 3 inches (3 to 8cm) away from the HomeLink button you wish to
program while keeping the HomeLink indicator light
in view.
3. Push and hold the Homelink button you want to program while you push and hold the hand-held
transmitter button.
4. Continue to hold both buttons and observe the indi- cator light. The Homelink indicator will flash slowly
and then rapidly after HomeLink has received the
frequency signal from the hand-held transmitter. Re-
lease both buttons after the indicator light changes
from slow to rapid.
5. Push and hold the programmed HomeLink button and observe the indicator light.
• If the indicator light stays on constantly, program-
ming is complete and the garage door/device should
activate when the HomeLink button is pushed. •
To program the two remaining HomeLink buttons,
repeat each step for each remaining button. DO NOT
erase the channels.
Reprogramming A Single HomeLink Button
(Non-Rolling Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Push and hold the desired HomeLink button until the indicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button proceed with “Program-
ming A Non-Rolling Code” step 2 and follow all
remaining steps.
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE