2016 Citroen DS5 HYBRID battery

69
DS5_en_Chap02_ouvertures_ed02-2015
Reinitialisation
If the blind meets an obstacle during
operation, you must reverse the
movement of the blind. To do this,
press the control switch for the blind in
question.
When the driver operates the blind
control switch, they must ensure that
no one is preventing correct closing of
the blind.
The driver must ensure that passengers
use the blind correctly.
Be particularly aware of children when
operating the blind.
If the blind opens again on its own
during a closing movement or soon
after stopping:
F
op

erate the control switch until the
blind is fully open,
F
th

en operate the control switch until
the blind is fully closed.
The safety anti-pinch function is not
operational during these operations.
In the event of a failure or battery disconnection
while a blind is moving or soon after it stops,
the safety anti-pinch must be reinitialised.
For each blind control switch:
F
op

erate the control until the blind is fully
closed,
F
co

ntinue to press for at least 3 seconds.
A slight movement of the blind will then be
noticeable, confirming the reinitialisation.
Access

101
DS5_en_Chap04_conduite_ed02-2015
Switching off using the
electronic key
F Immobilise the vehicle.
Electronic key left in the
reader
If the electronic key is left in the reader,
on opening the driver's door a message
appears to warn you.
Switching off with Keyless
Entry and Starting
F Immobilise the vehicle.I f the vehicle is not immobilised, the
engine will not stop.
Never leave your vehicle with the
electronic key still inside.
Switching the ignition on
(without starting)
F With the electronic key inside
t he vehicle, press the " S TA R T/
STOP " button.
The engine stops and the steering
column locks. F
Pr
ess the "
START/STOP "
button.
The engine stops and the steering
column locks.
Anti-theft protection
Electronic engine immobiliser
The keys contain an electronic chip which has
a secret code. When the ignition is switched
on, this code must be recognised in order for
starting to be possible.
This electronic engine immobiliser locks the
engine management system a few minutes
after the ignition is switched off and prevents
starting of the engine by anyone who does not
have the key.
In the event of a malfunction, you are informed
by a message in the instrument panel screen.
In this case, your vehicle does not start; contact
a CITROËN dealer as soon as possible.
With the electronic key in the reader or the
Keyless Entry and Starting key inside the
vehicle, pressing the "START/STOP" button,
with no action on the pedals
, allows the
ignition to be switched on.
F
Re

move the electronic key from the reader. F
Pr

ess the "START/STOP" button,
the instrument panel comes on
but the engine does not start.
F
Pr

ess the button again to switch
off the ignition and so allow the
vehicle to be locked.
With the ignition on, the system goes
into energy economy mode when
necessary to maintain the state of
charge of the battery.
Switching off the engine leads to a loss
of braking assistance.
driving

103
DS5_en_Chap04_conduite_ed02-2015
very cold conditions or
wh en towing
In these circumstances, it is
recommended that you do not apply the
parking brake.
For this, with the ignition on, deactivate
the automatic functions and release the
parking brake manually:
F
Ma

nual gearbox: engage first gear
or reverse.
F
Au

tomatic gearbox: select
position P .
The electric parking brake combines
2
o

perating modes:
-
Au

tomatic Application/Release
Ap

plication is automatic when the engine
stops, release is automatic on use of the
accelerator (this mode is activated by
default).
-
Ma

nual Application/Release
Ma

nual application of the parking brake is
done by pulling control lever A .
Ma

nual release is by pulling then
releasing the control lever, while pressing
the brake pedal.
Programming the automatic
mode
For some countries of sale, it is possible to
deactivate automatic operation.
In this case, deactivation is done via
the vehicle configuration menu.
Electric parking brake
If automatic mode is deactivated, the
parking brake must be applied and
released manually.
If this warning lamp comes on in
the instrument panel, the automatic
mode is deactivated.
Never leave the vehicle without
checking that the parking brake is on. This warning lamp comes on
fixed.
Label on door panel
dis

charged battery
In this case, the electric parking brake
no longer functions.
As a safety measure, immobilise the
vehicle following the recommendations
above or by placing a chock against one
of the wheels.
Call on a CITROËN dealer or a qualified
workshop.
When the driver's door is opened, there
is an audible signal and a message is
displayed if the parking brake is not
applied.
driving

DS5_en_Chap04_conduite_ed02-2015
Alertconsequences
To apply the electric parking brake:
F
im

mobilise the vehicle and switch off the ignition.
F
pu

ll the control for at least 5 seconds or until application is complete.
F
sw

itch on the ignition and check that the electric parking brake
warning lamps come on.
The application is slower than during normal operation.
To release the electric parking brake:
F
sw

itch on the ignition.
F
pu

ll the control lever and hold it for approximately 3 seconds then
release it.
If the braking warning lamp is flashing or if the warning lamps do not
come on with the ignition on, these procedures will not work. Place the
vehicle on level ground and have it checked by a CITROËN dealer or a
qualified workshop.
and possibly
flashing
Display of the message "
Parking brake fault" and illumination of these
warning lamps: -
On

ly the automatic application on switching off the engine and
automatic release on acceleration functions are available.
-
Th

e manual application/release of the electric parking brake and the
emergency braking are not available.
and possibly
flashing
Display of the message " Battery charge fault". -
Yo

u must stop as soon as it is safe to do so. Switch off and
immobilise your vehicle (if necessary, place the a chock under a
wheel).
-
Ap

ply the electric parking brake before switching off the engine.

DS5_en_Chap04_conduite_ed02-2015
Invalid value during manual
operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).
Stopping the vehicle
Before switching off the engine, put the selector
in position P or N to place the gearbox in
neutral.
In both cases, apply the parking brake to
immobilise the vehicle, unless it is programmed
to automatic mode.If the selector is not in position P ,
when the driver's door is opened or
approximately 45 seconds after the
ignition is switched off, there is an
audible signal and a message appears.
F
Re

turn the selector to position P ;
the audible signal stops and the
message disappears.
Operating fault
When the ignition is on, a message appears
in the instrument panel screen to indicate a
gearbox fault.
In this case, the gearbox switches to back-up
mode and is locked in 3rd gear. You may feel
a substantial knock when changing from P
to R and from N to R . This will not cause any
damage to the gearbox.
Do not exceed 60 mph (100 km/h), local speed
restrictions permitting.
Have it checked by a CITROËN dealer or a
qualified workshop. You risk damaging the gearbox:
-
if y

ou press the accelerator and
brake pedals at the same time,
-
if y

ou force the selector from
position P to another position when
the battery is flat.
To reduce fuel consumption when
stationary for long periods with the
engine running (traffic jam...), position
the gear selector at N and apply the
parking brake, unless it is programmed
in automatic mode.

11 9
DS5_en_Chap04_conduite_ed02-2015
Special cases: STOP mode not
available
STOP mode is not invoked when:
- the vehicle is on a steep slop (rising or
falling),
-
th

e driver's door is open,
-
th

e driver's seat belt is not fastened,
-
th

e vehicle has not exceeded 6 mph
(10
k

m/h) since the last engine start using
the START/STOP button,
-
th

e electric parking brake is applied or
being applied,
-
th

e engine is needed to maintain a
comfortable temperature in the passenger
compartment,
-
de

misting is active,
-
so

me special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed to assure control of a system.
In this case, the "E
cO" w

arning lamp
flashes for a few seconds then
goes off.
This operation is perfectly normal.
Going into engine START mode
The "EcO" w arning lamp goes off
and the engine starts automatically:
-
wi

th a manual gearbox , when you fully
depress the clutch pedal,
-
wi

th an automatic gearbox :
●
ge

ar selector in position
d o
r M, when
you release the brake pedal,
●
or g

ear selector in position N and brake
pedal released, when you place the gear
selector in position
d o

r M,
●
or w

hen you engage reverse. As a safety measure or to maintain comfort
levels in the vehicle, START mode is invoked
automatically when:
-
yo

u open the driver's door,
-
yo

u unfasten the driver's seat belt,
-
th

e speed of the vehicle exceeds 15
m
ph
(25 km/h) with a manual gearbox (2
m

ph
(3
k

m/h) with THP 210 petrol and
BlueHDi
1

15 and 120 Diesel versions), or
2
m

ph (3
k
m/h) with an automatic gearbox,
-
th

e electric parking brake is being applied,
-
so

me special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed for control of a system.
Special cases: START invoked
automatically
In this case the "EcO" w arning lamp
flashes for a few seconds, then
goes off.
This operation is perfectly normal.
driving

121
DS5_en_Chap04_conduite_ed02-2015
Operating fault
In the event of a fault in STOP mode, the
vehicle may stall.
All of the instrument panel warning lamps
come on.
It is then necessary to switch off the ignition
and start the engine again using the "S TA R T/
STOP " button.
In the event of a fault with the system, the
button in the "E
cO OF

F" switch flashes for a
few moments, then remains on.
Have it checked by a CITROËN dealer or a
qualified workshop. The Stop & Start system requires a
12
V b
attery of specific technology and
specification.
All work on this type of battery must be
carried out only by a CITROËN dealer
or a qualified workshop.
For more information on the 12 V
battery, refer to the corresponding
section.
driving

145
DS5_en_Chap05_visibilite_ed02-2015
Switching off the lighting
when switching off the ignition
When the ignition is switched off, all of the
lamps switch off immediately, except for
the dipped beam headlamps if automatic
guide-me-home lighting is activated.In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.
Switching on the lighting when
switching on the ignition
To reactivate the lighting control stalk,
turn the ring A to position "0"
- lighting
off, then to the position of your choice.
When the driver's door is opened, a
temporary audible signal warns you that
the vehicle's lighting is on.
They switch off automatically after a
period which depends on the state of
charge of the battery (entry to energy
economy mode).
daytime running lamps /
S idelamps
(LE
ds)
The light-emitting diodes (LEDs) come on
automatically when the engine is started.
They provide the following functions:
-
Da

ytime running lamps (lighting control
stalk in position " 0" or " AUTO " with
adequate light level).
-
Si

delamps (lighting control stalk in
position " AUTO" with low light level or
"Sidelamps only" or "Main or dipped beam
headlamps").
The LEDs are brighter when operating as
daytime running lamps.
visibility