2016 CITROEN DS3 CABRIO DAG bonnet

DS3_en_Chap00a_sommaire_ed01-2015
CHECKSTECHn ICAL dA TAAUdI O and
TELEMATICS
239 Bonnet
240 Pe trol   engines
241
 D

iesel
 eng
ines
242
 C

hecking   levels
246
 C

hecks 250 Pe
trol   engines
253 Pe trol   weights
256
 LP

G
 e
ngine
257
 L

PG   weights
258
 D

iesel
 eng
ines
259
 D

iesel
 eng
ines
260
 D

imensions
262
 I

dentification
 ma
rkings266 E
mergency   or   assistance
269 7 -inch touch screen tablet
331
 A

udio   system
0100 11009

39
DS3_en_Chap01_controle-de-marche_ed01-2015
On vehicles fitted with an electric oil level
indicator,  information   on   the   oil   level   is  
d

isplayed   in   the   instrument   panel   for   a   few  
s

econds   when   the   ignition   is   switched   on,   after  
t

he   service   information.
Engine oil level indicator*
The level shown will only be correct
if  the   vehicle   is   on   level   ground   and  
t

he   engine   has   been   off   for   more   than  
3

0 minutes.
Oil level correct
Oil level low
This is indicated by the flashing of " O I L" ,
a ccompanied   by   illumination   of   the   service  
w

arning   lamp,   an   audible   signal   and   a  
m

essage.
If
  the   low   oil   level   is   confirmed   by   a   check   using  
t

he   dipstick,   the   level   must   be   topped   up   to  
p

revent   damage   to   the   engine.
Refer
  to   the   "Checking   levels"   section.
Oil level indicator fault
This is signaled by the flashing of "OIL- -".
C ontact   a   CITROËN   dealer   or   a   qualified  
w

orkshop.
In the event of a fault with the electric oil level
indicator,
  the   engine   oil   level   is   no   longer  
mon

itored.
While
  the   system   is   faulty,   you   should   check  
t

he   engine   oil   level   using   the   manual   dipstick  
l

ocated   under   the   bonnet.
Refer
  to   the   "Checking   levels"   section.
*
  Depending   on   version.
Monitoring

135
DS3_en_Chap05_visibilite_ed01-2015
Travelling abroad
LEd / Xenon front lamps
For motoring in countries that drive on the other s
ide   of   the   road,   it   is   necessary   to   adjust   the  
d

ipped   beams   so   as   to   not   dazzle   the   drivers   of  
a

pproaching
 v
ehicles.
F
 
R
aise   the   bonnet   for   access   to   the   adjuster  
(

one   adjuster   per   headlamp).
F
 
I
nsert   a   suitable   allen   key   (not   supplied)  
i

nto   the   hexagonal   head   of   the   adjuster.
F
 
T
urn   the   allen   key   half   a   turn   clockwise.
Headlamp adjustment
To avoid causing a nuisance to other road u
sers,   the   height   of   the   headlamps   should   be  
a

djusted   in   relation   to   the   load   in   the   vehicle.
0.
 
D
river   only   or   driver   +   front   passenger.
-.
 I

ntermediate
 s
etting.
1.
 5

  people.
-.
 
5
  people   +   load   in   the   boot.
2.
 D

river   only   +   maximum   authorised   load   in  
t

he   boot.
This
  position   is   sufficient   to   avoid   causing  
d

azzle.
Higher
  settings   may   limit   the   spread   of   light  
f

rom   the   headlamps.
The
  initial   setting   is   position   "0". On
  your   return,   don't   forget   to  
a

djust   your   headlamps   back   to   their  
i

nitial   setting,   by   carrying   out   these  
o

perations   in   reverse   order.
Visibility

139
DS3_en_Chap05_visibilite_ed01-2015
Operating fault
If an automatic wiping fault occurs, the wipers will   operate   in   intermittent   mode.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
To retain the effectiveness of the flat
wiper
  blades,   it   is   advisable   to:
-
 
h
andle   them   with   care,
-
 
c
lean   them   regularly   using   soapy  
w

ater,
-
 
n
ot   use   them   to   hold   a   sheet   of  
c

ardboard   against   the   windscreen,
-
 
r
eplace   them   at   the   first   signs   of  
w

e a r.
Do
  not   cover   the   rain   sensor,   linked  
w

ith the sunshine sensor and located in
the centre of the windscreen behind the
rear
  view   mirror.
Switch
  off   the   automatic   wiping   when  
u

sing   an   automatic   car   wash.
In winter, it is advisable to wait until the
windscreen
  is   completely   clear   of   ice  
b

efore   activating   the   automatic   wiping.This position allows the wiper blades to
be
  lifted   for   winter   parking,   cleaning   or  
r

eplacement   without   damaging   the   bonnet.
In
  the   minute   following   switching   off   of   the  
i

gnition,   any   action   on   the   wiper   stalk   positions  
t

he   wipers   vertically.
To
  park   the   wipers   after   this   has   been   done,
 s

witch   on   the   ignition   and   operate   the   wiper   stalk.
Vertical windscreen wiper
position
Visibility

Operating faults
In the event of an impact to the windscreen at the sensor, deactivate
the
  system   and   contact   a   CITROËN  
d

ealer   or   a   qualified   workshop to   have  
y

our   windscreen   replaced.
Never
  try   to   remove,   adjust   or   test  
t

he sensor.
Only
  a   CITROËN   dealer   or   a   qualified
 w

orkshop   is   able   to   work   on   the   system.
When
  towing   a   trailer   or   when   the  
v

ehicle   is   being   towed,   the   system   must  
b

e   deactivated.Do not stick or other wise fix any object on the   windscreen   in   front   of   the   sensor.
Sensor fault
The operation of the laser sensor may suffer inter ference   from   accumulations   of   dirt   or  
m

isting   of   the   windscreen.   In   this   case   you   are  
w

arned   by   the   display   of   a   message.
Use
  the   windscreen   demisting   and   regularly  
c

lean the area of the windscreen in front of the
sensor.
System fault
In the event of a malfunction of the system, you a re   warned   by   an   audible   signal   and   the   display  
o

f   the   message   "Automatic braking system
fault" .
Have
  the   system   checked   by   a   CITROËN  
d

ealer   or   a   qualified   workshop.
In
 
difficult
 
weather
 
conditions
 
(very
 h
eavy
 
rain,
 
snow,
 
fog,
 
hail...),
 
braking
 
d

istances increase, which can reduce
the
 
ability
 
of
 
the
 
system
 
to
 
avoid
 
a
 
c

ollision.
The
 
driver
 
must
 
therefore
 
remain
 
par

ticularly
 v

igilant.
Never
 
leave
 
accumulations
 
of
 
snow
 
or
 
a

ny
 
object
 
projecting
 
above
 
the
 
bonnet
 
o

r
 
in
 
front
 
of
 
the
 
roof:
 
this
 
might
 
fall
 
into
 
t

he field of vision of the sensor and
generate
 
a
 
detection.

187
DS3_en_Chap08_info-pratiques_ed01-2015
Running out of fuel (Diesel)If your vehicle has an HDi engine, the fuel system must be primed if you run out of fuel.
T his   system   consists   of   a   priming   pump   and   a   transparent   pipe   under   the   bonnet.
F
 
F
ill   the   fuel   tank   with   at   least   five   litres   of  
D

iesel.
F
 
O
pen   the   bonnet.
F
 
D
epending   on   version,   unclip   the   cover   to  
g

ain   access   to   the   priming   pump.
F
 
S
queeze   and   release   the   priming   pump  
u

ntil   resistance   is   felt   (could   be   from   the  
f

irst   application)   and   fuel   appears   in   the  
t

ransparent   pipe   with   the   green   connector.
F
 
O
perate   the   starter   until   the   engine   starts.
F
 
D
epending   on   version,   put   the   cover   back  
i

n   position   and   clip   it   in   place.
F
 
C
lose   the   bonnet.
BlueHdi 100 engines
F Fill  the   fuel   tank   with   at   least   five   litres   of  D
iesel.
F
 
S
witch   on   the   ignition   (without   starting   the  
e

ngine).
F

W
ait around 6 seconds and switch off the
ignition.
F
 
R
epeat   the   operation   10   times.
F
 
O
perate   the   starter   to   run   the   engine.
If
 
the
 
engine
 
does
 
not
 
start
 
at
 
the
 
first
 
a

ttempt,
 
do
 
not
 
try
 
again.
Operate
 
the
 
priming
 
pump
 
again,
 
then
 
t

he
 
starter.
Practical information

223
DS3_en_Chap08_info-pratiques_ed01-2015
BatteryProcedure for charging your battery when it is flat or for starting the engine using another battery.T he   battery   is   located   under   the   bonnet.
To
  gain   access   to   it:
F
 
o
pen   the   bonnet   using   the   interior   release  
l

ever,   then   the   exterior   safety   catch,
F

s
ecure the bonnet stay,
F
 
l
ift   the   plastic   cover   on   the   (+)   terminal.
Access to the batteryAfter refitting the battery by a CITROËN   dealer   or   a   qualified  
w

orkshop,   the   Stop   &   Start   system  
w

ill only be active after a continuous
period
  of   immobilisation   of   the   vehicle,  
a

  period   which   depends   on   the   climatic  
c

onditions   and   the   state   of   charge   of  
t

he   battery   (up   to   about   8   hours).
The presence of this label, in particular
with
 
the
 
Stop
 
&
 
Start
 
system,
 
indicates
 
t

he use of a 12 V lead-acid battery with
special
 t

echnology
 a

nd
 s

pecification;
 t

he
 
involvement
 
of
 
a
 
CITROËN
 
dealer
 
o

r
 
a
 
qualified
 
workshop
 
is
 
essential
 
w

hen
 
replacing
 
or
 
disconnecting
 
the
 
b

attery.
Failure
 
t

o
 
o

bserve
 
t

his
 
r

ecommendation
 
m

ay
 
cause
 
premature
 
wear
 
of
 
the
 
b

attery.
Practical information

227
DS3_en_Chap08_info-pratiques_ed01-2015
Changing a front or rear wiper bladeProcedure for replacing a worn wiper blade with a new one without the use of tools.
Before removing a front
wiper blade
F Within  one   minute   after   switching   off   the  i
gnition,   operate   the   wiper   stalk   to   position  
t

he   wiper   blades   in   the   vertical   position.
This
  position   must   be   used   in   order   to   avoid  
d

amaging   the   wiper   blade   and   the   bonnet.
Removal
F Raise  the   corresponding   wiper   arm.
F  U nclip   the   wiper   blade   and   remove   it.
Fitting
F At  the   front,   check   the   size   of   the   wiper  b
lade as the shorter blade is fitted to the
passenger
  side   of   the   vehicle.
F
 
P
ut   the   corresponding   new   wiper   blade   in  
p

lace   and   clip   it.
F
 
F
old   down   the   wiper   arm   carefully.
After fitting a front wiper
blade
F Switch  on   the   ignition.
F  O perate   the   wiper   stalk   again   to   park   the  
w

iper   blades.
Practical information