2016 Citroen C4 lock

171
C4-2_en_Chap06_conduite_ed02-2015
Starting / Switching off the engine with Keyless Entry and 
S
tarting
Starting the engine
It is not necessary to place the electronic key in t
he r eader. F
B riefly press the "S TA R T/
STOP "
  button   while   maintaining  
p

ressure on the pedal until the
engine
 s

tarts.
The
  steering   column   unlocks   and   the  
e

ngine
 s
tarts.
See the advice below for Diesel
versions.
If
  this   warning   lamp   comes   on   after  
p

ressing   "START/STOP ", you should
hold
  the   brake   or   clutch   pedal   down  
u

ntil   the   warning   lamp   goes   off   and   do  
n

ot press the "START/STOP " button
again.
If
  one   of   the   starting   conditions   is   not
 m

et,   a   reminder   message   appears   in
 t

he   instrument   panel   screen.   In   some
 c

ircumstances,   it   is   necessary   to   turn
 t

he   steering   wheel   slightly   while   pressing
 t

he "START/STOP " button to assist
unlocking
  of   the   steering;   a   message
 w

arns   you   when   this   is   needed.If
  the   electronic   key   is   not   detected   in  
t

he   zone,   a   message   is   displayed.   Move  
t

he   electronic   key   into   the   zone   so   that  
t

he   engine   can   be   started.
The presence of the "Keyless Entry
and
  Starting"   electronic   key   in   the  
r

ecognition   zone   is   essential.
As
  a   safety   measure,   do   not   leave   this  
z

one   with   the   vehicle   running.In
  temperatures   below   zero  
t

he   engine   will   not   start   until  
t

he   preheater   warning   lamp  
h

as   gone   off.
F
 
P
lace   the   gear   selector   lever   P or N with
an
  automatic   gearbox,   or   neutral   with   a  
m

anual
 g
earbox.
F
 
W
ith   the   electronic   key   inside   the   vehicle,  
p

ress   the   brake   pedal   for   vehicles   with   an  
a

utomatic   gearbox,   or   fully   declutch   for  
v

ehicles   with   a   manual   gearbox.
Diesel vehicles
6
Driving

172
C4-2_en_Chap06_conduite_ed02-2015
Switching off the engine
F Immobilise  the   vehicle.
F  P lace   the   gear   selector   at   P or N with
an
  automatic   gearbox,   or   neutral   with   a  
m

anual
 g
earbox.
Do not leave your vehicle with the
electronic
  key   still   inside.
Switching
  off   the   engine   leads   to   a   loss  
o

f   braking   assistance.
If
  the   vehicle   is   not   immobilised,   the  
e

ngine   will   not   stop.
F
 
W
ith   the   electronic   key   inside  
t

he vehicle, press the " S TA R T/
STOP "
  button.
The
  engine   stops   and   the   steering  
c

olumn   locks.
Emergency starting
When the electronic key is in the recognition zone   and,   after   pressing   the   "START/STOP "
button,
  the   engine   does   not   start:
F
 
P
lace   the   gear   selector   at   P or N for
vehicles
  with   an   automatic   gearbox   or  
n

eutral   for   vehicles   with   a   manual   gearbox.F
 O pen   the   front   armrest.
F
 
R
aise   the   mat   by   its   tab   and   remove   it.
F
 
P
lace   the   electronic   key   in   the   back-up  
re

ader.
F
 
P
ress   the   brake   pedal   on   vehicles   with   an  
a

utomatic   gearbox,   or   fully   declutch   with   a  
m

anual
 g
earbox.
F

P
ress the "START/STOP "
button.
 T

he   engine   starts.
Driving

173
C4-2_en_Chap06_conduite_ed02-2015
Emergency switch-off
In the event of an emergency only, the  e ngine  c an  b e  s witched  o f  w ithout  
c

onditions.   To   do   this,   press   and   hold  
t

he " START/STOP " button for about
3
  seconds.
In
 
this
 
case   the   steering   column   locks   as   soon  
a

s
 
the
 
vehicle   stops.
Electronic key not
recognised
If the electronic key is no longer in the recognition   zone   when   driving   or   when   you  
(

later)   request   switching   off   the   engine,   a  
m

essage   is   displayed.
F

P
ress and hold the " S TA R T/
STOP " button for about
3 seconds
  if   you   want   to   force  
s

witching   off   the   engine   (note
that restar ting will not be
possible without the key ).
Ignition on position
(without starting)
With the Keyless Entry and Starting key inside t
he   vehicle,   pressing   the   "START/STOP "
button, with no action on the pedals , allows
the
  ignition   to   be   switched   on.
With
  the   ignition   on,   the   system  
a

utomatically   goes   into   energy  
e

conomy   mode   when   required   to  
m

aintain   the   state   of   charge   of   the  
b

attery.F

P
ress the "START/STOP "
button,
  the   instrument   panel  
c

omes   on   but   the   engine   does  
n

ot   start.
F
 
P
ress   the   button   again   to   switch   off   the  
i

gnition   and   so   allow   the   vehicle   to   be  
lo

cked.
6
Driving

186
C4-2_en_Chap06_conduite_ed02-2015
When the ignition is on, a message appears   in   the   instrument   panel  
s

creen   to   indicate   a   gearbox   fault.
Operating fault
You risk damaging the gearbox:
- i f you press the accelerator and
brake
  pedals   at   the   same   time,
-
 
i
f   you   force   the   selector   from  
p

osition P to another position when
the
  battery   is   flat.
To
  reduce   fuel   consumption   when  
s

tationary   for   long   periods   with   the  
e

ngine   running   (traffic   jam...),   position  
t

he   gear   selector   at   N and apply the
parking
  brake,   unless   it   is   programmed  
i

n   automatic   mode.
In
 
this
 
case,
 
the
 
gearbox
 
switches
 
to
 
back-up
 
m

ode
 
and
 
is
 
locked
 
in
 
3rd
 
gear.
 
You
 
may
 
feel
 
a

 
substantial
 
knock
 
when
 
changing
 
from
 
P
to R
 
and
 
from
 
N to R .
 
This
 
will
 
not
 
cause
 
any
 
d

amage
 
to
 
the
 
gearbox.
Do
 
not
 
exceed
 
60
 
mph
 
(100
 
km/h),
 
local
 
speed
 
r

estrictions
 p

ermitting.
Have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or
 
a
 
q

ualified
 w

orkshop.
Driving

214
C4-2_en_Chap07_infos-pratiques_ed02-2015
Towbar with quickly detachable towball
Presentation
This towbar allows the towball to be fitted and
removed  quickly   and   easily   without   the   use  
o

f   tools.   Installed   behind   the   rear   bumper,   the  
t

owbar   is   invisible   after   removing   the   towball  
a

nd   folding   the   trailer   harness   socket   carrier.
1.


Carrier
2.
 P

rotective   blanking   plug.
3.
 S

ecurity   ring.
4.
 F

olding   trailer   harness   socket.
5.
 D

etachable
 t
owball.
6.
 L

ocking   /   unlocking   wheel.
7.
 S

ecurity   key   lock.
8.
 L

ocking   wheel   protector.
9.
 Ba

ll
 pro
tector.
10.
 St

orage
 b
ag.A. Locked position
The locking wheel is not in contact with the towball   (gap   of   about   5   mm).
The
  green   mark   is   visible.
The
  lock   for   the   locking   wheel   is   facing  
r

earward.
B. Unlocked position
The locking wheel is in contact with the towball.
T hen   green   mark   is   hidden.
The
  lock   for   the   locking   wheel   is   facing   for ward.
Observe
  the   legislation   in   force   in   the  
c

ountry   in   which   you   are   driving.
For
  information   on   the   maximum   trailer  
w

eight   and   the   recommended   nose  
w

eight,   refer   to   the   "Technical   data"  
s

ection.
For
  information   on   safely   towing   a  
t

railer,   refer   to   the   "Towing   a   trailer"  
s

ection.
Practical information

215
C4-2_en_Chap07_infos-pratiques_ed02-2015
Before each use
Check that the towball is correctly fitted by verifying the following points:
-  t he   towball   is   correctly   locked   in   place   (position   A),
-
 
t
he   security   key   lock   is   on   and   the   key   removed;   the   locking   wheel   can   no   longer   be  
ope

rated,
-
 
t
he   towball   must   no   longer   move   at   all   in   its   carrier;   try   to   shake   it   by   hand.
During use
Never unlock the device when a trailer or load carrier is fitted to the towball.
N ever   exceed   the   maximum   authorised   weight   for   the   vehicle   plus   trailer   (Gross   Train  
W

eight   -   GTW).
Before
  driving,   check   the   adjustment   of   the   headlamp   beam   height.
For
  more   information   on   adjusting   the   headlamps,   refer   to   the   corresponding   section.
After use
For journeys made without a trailer or load carrier, the trailer harness socket must be folded away,   the   towball   removed   and    the   blanking   plug   inserted   in   the   carrier.   This   measure  
a

pplies   particularly   if   the   towball   could   hinder   visibility   of   the   number   plate   or   lighting.
7
Practical information

216
C4-2_en_Chap07_infos-pratiques_ed02-2015
Fitting the towball
Remove the protective plug from the carrier and   check   the   condition   of   the   fixing   system.  
I

f necessary, clean the carrier with a brush or
clean
  cloth.
Take
  the   towball   from   the   storage   bag.
Remove
  the   protective   cover   from   the   ball   and  
t

he   protective   cap   from   the   locking   wheel.
Stow
  the   plug,   cover   and   cap   in   the  
s

torage bag.
Check
  that   the   towball   is   unlocked   (position   B).
 
I

f   not,   insert   the   key   in   the   lock   and   turn   the   key  
a

nti-clockwise   to   unlock   the   mechanism.Take
  the   towball   in   both   hands;   insert   the   end  o
f   the   towball   into   the   carrier   by   lifting   it,   then,  
t

o   ensure   that   it   has   correctly   locked   in   place,  
p

ull   firmly   down   on   the   ball   end   of   the   towball.
The
  locking   wheel   automatically   turns   a   quarter  
o

f   a   turn   anti-clockwise,   making   a   perceptible  
c

lick;   take   care   to   keep   your   hands   clear.Check
  that   the   towball   has   correctly   locked   in  p
lace   (position   A).
Turn
  the   key   clockwise   to   lock   the   towball   fixing  
m

echanism.
Always
  remove   the   key   and   keep   it   in   a   safe  
p

lace.If
  the   key   cannot   be   turned   or   removed,  
t

his   means   that   the   towball   is   not   fitted  
c

orrectly;   start   the   procedure   again.
If
  one   of   the   locking   conditions   is   not  
m

et,   start   the   procedure   again.
In
  all   cases,   if   the   marking   remains  
r

ed, do not use the towbar and contact
a
  CITROËN   dealer   or   a   qualified  
w

orkshop.
Practical information

217
C4-2_en_Chap07_infos-pratiques_ed02-2015
Attach the trailer to the towball.
A ttach the cable on the trailer to the security
ring
  located   on   the   carrier.
Lower
  the   trailer   harness   socket   carrier   by  
p

ulling   down   on   the   ring   visible   below   the  
b

u m p e r.
Remove
  the   protective   cover   from   the   socket  
a

nd   connect   the   trailer   wiring   harness.
Removing the towball
Disconnect the trailer harness from the socket on   the   carrier.
Detach
  the   cable   on   the   trailer   from   the   security  
r

ing   on   the   carrier.
Unhook
  the   trailer   from   the   towball.
Return the trailer harness connector carrier to
the
  folded   position. Insert
  the   key   into   the   lock.
Turn   the   key   anti-clockwise   to   unlock   the  
t

owball
 f
ixing
 m
echanism.
7
Practical information