2016 Citroen C4 low beam

167
C4-2_en_Chap06_conduite_ed02-2015
When towing
Distribution of loads
F Distribute the load in the trailer so that the heaviest   items   are   as   close   as   possible   to t

he   axle   and   the   nose   weight   approaches   the
 m

aximum   permitted   without   exceeding   it.
Air density decreases with altitude,
thus
 r

educing
 e
ngine
 p
erformance.
 A

bove 1 000 metres,   the   maximum   towed  
l

oad   must   be   reduced   by   10 %   for   every  
1 0

00 metres   of   altitude.
Side wind
F Take  into   account   the   increased   sensitivity  t
o   side   wind.
For
  more   information   on   weights   (and   the  
t

owed   loads   which   apply   to   your   vehicle)   refer  
t

o   the   corresponding   section.
F  
I
f   the   warning   lamp   and   the  
S

TOP
 
warning   lamp   come   on,  
s

top the vehicle and switch off
the   engine   as   soon   as   possible.
Braking
Towing a trailer increases the braking distance.
T o   avoid   overheating   of   the   brakes,   the   use   of  
e

ngine   braking   is   recommended.
Ty r e s
F Check  the   tyre   pressures   of   the   towing  v
ehicle   and   of   the   trailer,   observing   the  
re

commended
 p
ressures.
Lighting
F Check  the   electrical   lighting   and   signalling  o
n   the   trailer   and   the   hadlamp   beam   height  
o

f   your   vehicle.
For
  more   information   on   adjusting   the  
h

eadlamp   beam   height,   refer   to   the  
c

orresponding
 s
ection.
The
  rear   parking   sensors   will   be  
d

eactivated   automatically   if   a   genuine  
C

ITROËN   towbar   is   used.
Cooling
Towing a trailer on a slope increases the temperature   of   the   coolant.
As
  the   fan   is   electrically   controlled,   its   cooling  
c

apacity   is   not   dependent   on   the   engine   speed.
F
 
T
o   lower   the   engine   speed,   reduce   your  
s

peed.
The
  maximum   towed   load   on   a   long   incline  
d

epends   on   the   gradient   and   the   ambient  
t

emperature.
In
  all   cases,   keep   a   check   on   the   coolant  
t

emperature.
6
Driving

215
C4-2_en_Chap07_infos-pratiques_ed02-2015
Before each use
Check that the towball is correctly fitted by verifying the following points:
-  t he   towball   is   correctly   locked   in   place   (position   A),
-
 
t
he   security   key   lock   is   on   and   the   key   removed;   the   locking   wheel   can   no   longer   be  
ope

rated,
-
 
t
he   towball   must   no   longer   move   at   all   in   its   carrier;   try   to   shake   it   by   hand.
During use
Never unlock the device when a trailer or load carrier is fitted to the towball.
N ever   exceed   the   maximum   authorised   weight   for   the   vehicle   plus   trailer   (Gross   Train  
W

eight   -   GTW).
Before
  driving,   check   the   adjustment   of   the   headlamp   beam   height.
For
  more   information   on   adjusting   the   headlamps,   refer   to   the   corresponding   section.
After use
For journeys made without a trailer or load carrier, the trailer harness socket must be folded away,   the   towball   removed   and    the   blanking   plug   inserted   in   the   carrier.   This   measure  
a

pplies   particularly   if   the   towball   could   hinder   visibility   of   the   number   plate   or   lighting.
7
Practical information

252
C4-2_en_Chap08_en-cas-de-panne_ed02-2015
F Remove  the   air   deflector   by   unclipping  e
ach   of   its   three   attachment   points.
F
 
U
nclip   the   bonnet   release   cable   at   its  
two
  fixings.
F
 
M
ove   the   cable   down.
After
  changing   the   failed   bulb,   remember   to  
p

ut   everything   back   in   place   (cable   and   air  
d

eflector).
Depending
  on   the   engine   and   only   on   the   left  
h

and   side,   you   must   first   carry   out   the   following  
o

perations for access to the protective covers
on   the   bulbs.
Access to bulbs
Model with halogen headlamps
and LED light signature* (type 2)
1. Direction indicators (LEDs).
2. Daytime running lamps / sidelamps (LEDs).3. Dipped beam headlamps (H7).
4. M
ain beam headlamps (H7).
5.
F

o g l a m p s ( H11) .
Bulbs
  with   lugs,   type   H1,   H7...   take   care  
t

o   position   them   correctly   to   ensure   the  
b

est
 l
ighting.
Model with halogen headlamps
(t y p e 1)
1. Direction indicators (H21 clear).
2. Dipped beam headlamps (H7).
3.
M

ain beam headlamps (H1).
4.
D

aytime running lamps / sidelamps
(P21/5W XL).
5.
F

o g l a m p s ( H11) .Bulbs
  with   lugs,   type   H1,   H7...   take   care  
t

o   position   them   correctly   to   ensure   the  
b

est
 l
ighting.
*
  LED:   light   emitting   diodes.
In the event of a breakdown

264
C4-2_en_Chap08_en-cas-de-panne_ed02-2015
Fuse N°Rating Functions
F19 30 AWindscreen
  wipers   slow   /   fast   speed.
F20 15 AFront
  and   rear   screenwash   pump.
F21 20 AHeadlamp
  wash   pump.
F22 15 AHorn.
F23 15 ARight-hand
  main   beam   headlamp.
F24 15 ALeft-hand
  main   beam   headlamp.
F27 5 ALeft-hand
 d

ipped
 h
eadlamp.
F28 5 ARight-hand
 d

ipped
 h
eadlamp.
Engine compartment fuses
The fusebox is placed in the engine compartment   near   the   battery   (left-hand   side).
Access to the fuses
F Unclip  the   cover.
F  C hange   the   fuse.
For
  information   on   the   special   requirements  
a

nd  
p
recautions  
t
o  
t
ake  
b
efore  
c
hanging  
a
 
f
use,  
r

efer   to   the   start   of   this   section.
F

W
hen you have finished, close the cover
carefully
  to   ensure   sealing   of   the   fusebox.
Fuse table
In the event of a breakdown