2016 Citroen C4 CACTUS stop start

208
Dashboard fuses
The two fuseboxes are placed in the lower dashboard,   at   the   glove   box. Fuse
N° Rating
(A) Functions
F01 10Brake   pedal   (switch   2),   Stop   &   Start.
F02 5Headlamp   beam   height   adjuster,   additional   heater   (Diesel),  
p

arking   sensors,   diagnostic   socket,   door   mirrors   (electric  
a

djustment),   Grip   Control.
F03 10Diesel   additive   pump,   electric   power   steering,   clutch   pedal  (
sw i tc h).
F04 5Rain
  and   sunshine   sensor.
F06 10Brake
  pedal   (switch   1),   diagnostic   socket.
F08 5Top
  of   steering   column   contacts   with   steering   mounted   controls.
F10 15Emergency
  call   /   Assistance   call.
F12 5Stop
  &   Start,   ABS,   ESC.
F13 5Parking
  sensors,   reversing   camera
F14 10Electronic
  gearbox,   switch   panel   (below   the   touch   screen  
t

ablet),   air   conditioning,   touch   screen   tablet.
F16 1512
  Volt   socket.
F18 20Radio.
Access to the fuses
F Unclip  the   cover   by   pulling   at   top   left,   then  r
ight.
Left hand fusebox
In the event of a breakdown

211
Engine compartment fuses
Access to the fuses
F Unclip  the   cover.
F  C hange   the   fuse   (see   corresponding  
par

agraph).
F
 
W
hen   you   have   finished,   close   the   cover  
c

arefully   to   ensure   correct   sealing   of   the  
f

usebox. Fuse
N° Rating
(A) Functions
F1 40Air
 c
onditioning.
F2 30 / 40Stop   &   Start.
F3 30Passenger
 c
ompartment
 f
usebox.
F4 70Passenger
 c
ompartment
 f
usebox.
F5 70Built-in   Systems   Inter face   (BSI).
F6 60Cooling   fan   assembly.
F7 80Built-in   Systems   Inter face   (BSI).
F8 15Engine
  management,   petrol   pump.
F9 15Engine
 m

anagement.
F10 15Engine
 m

anagement.
F11 20Engine
 m

anagement.
F12 5Cooling
  fan   assembly.
F13 5Built-in
  Systems   Inter face   (BSI).
F14 5Battery
  charge   unit   (non   Stop   &   Start   engine).
F15 5Stop
  &   Start.
F17 5Built-in
  Systems   Inter face   (BSI).
F18 10Right
  hand   main   beam   headlamp.
The
  fusebox   is   placed   in   the   engine  
c

ompartment   near   the   battery.
8
In the event of a breakdown

213
12 V battery
The battery is located under the bonnet.
T o   gain   access   to   it:
F
 
o
pen   the   bonnet   using   the   interior   release  
l

ever,   then   the   exterior   safety   catch,
F

s
ecure the bonnet stay,
F
 
l
ift   the   plastic   cover   on   the   (+)   terminal.
Access to the battery
Procedure for starting the engine using another battery or charging a discharged battery.
P rotect   your   eyes   and   face   before  
h

andling   the   battery.
All
  operations   on   the   battery   must   be  
c

arried   out   in   a   well   ventilated   area   and  
a

way   from   naked   flames   and   sources  
o

f   sparks,   so   as   to   avoid   the   risk   of  
e

xplosion   or   fire.
Wash
  your   hands   after wards.
Versions
  equipped   with   Stop   &   Start   are  
f

itted   with   a   12   V   lead-acid   battery   of  
s

pecific
 t
echnology
 a
nd
 s
pecification.
Its
  replacement   should   be   carried   out  
o

nly
 
by
 
a
 
CITROËN
 
dealer
 
or
 
a
 
qualified
 w

orkshop.
General points
Lead-acid starter batteries
Batteries contain harmful substances such   as   sulphuric   acid   and   lead.
They
  must   be   disposed   of   in  
a

ccordance   with   regulations   and   must  
n

ot,   in   any   circumstances,   be   discarded  
w

ith   household   waste.
Take
  used   remote   control   batteries   and  
v

ehicle batteries to a special collection
point.
With
  an   electronic   gearbox,   do   not   try   to  
s

tart   the   engine   by   pushing   the   vehicle.The
  (-)   battery   terminal   is   not   accessible.
A
  remote   earth   point   is   located   on   the   right-
hand
  front   wing.
8
In the event of a breakdown

214
When your vehicle's battery is discharged, the engine   can   be   started   using   a   slave   battery  
(

external   or   on   another   vehicle)   and   jump   lead  
c

ables   or   a   battery   booster.
Starting using another battery
F Raise  the   plastic   cover   on   the   (+)   terminal,  i
f   your   vehicle   has   one.
F
 
C
onnect   the   red   cable   to   the   positive  
t

erminal   (+)   of   the   flat   battery   A (at
the
  metal   elbow)   then   to   the   positive  
t

erminal (+)   of   the   slave   battery   B or
the booster.
F
 
C
onnect   one   end   of   the   green   or   black  
c

able   to   the   negative   terminal   (-)   of   the  
s

lave battery B or the booster (or earth
point
  on   the   other   vehicle).
F
 
C
onnect  
t
he  
o
ther  
e
nd  
o
f  
t
he  
g
reen  
o
r  
b
lack  
c

able to the earth point C   on   the   broken  
d

own   vehicle. F
 
S
tart   the   engine   of   the   vehicle   with   the  
g

ood   battery   and   leave   it   running   for   a   few  
m

inutes.
F  
O
perate   the   starter   on   the   broken   down  
v

ehicle   and   let   the   engine   run.
If   the   engine   does   not   start   straight   away,  
s

witch   off   the   ignition   and   wait   a   few   moments  
b

efore   trying   again.
Never
 
try
 
to
 
start
 
the
 
engine
 
by
 
c

onnecting
 
a
 
battery
 
charger.
Never
 
use
 
a
 
24
 
V
 
or
 
higher
 
battery
 
b

o o s t e r.
First
 
check
 
that
 
the
 
slave
 
battery
 
has
 
a
 
n

ominal
 
voltage
 
of
 
12
 
V
 
and
 
a
 
capacity
 
a

t
 
least
 
equal
 
to
 
that
 
of
 
the
 
discharged
 
b

attery.
The
 
two
 
vehicles
 
must
 
not
 
be
 
in
 
contact
 w
ith
 
each
 
other.
Switch
 
off
 
the
 
electrical
 
consumers
 
on
 
b

oth
 
vehicles
 
(audio
 
system,
 
wipers,
 
l

ighting, ...).
Ensure
 
that
 
the
 
jump
 
lead
 
cables
 
do
 
n

ot
 
pass
 
close
 
to
 
moving
 
parts
 
of
 
the
 
e

ngine
 
(cooling
 
fan,
 
belts, ...).
Do
 
not
 
disconnect
 
the
 
(+)
 
terminal
 
when
 
t

he
 
engine
 
is
 
running. F
 
W
ait   until   the   engine   returns   to   idle   then  
d

isconnect   the   jump   lead   cables   in   the  
r

everse
 o
rder.
F  
R
efit   the   plastic   cover   to   the   (+)   terminal,   if  
y

our   vehicle   has   one.
F  A llow   the   engine   to   run   for   at   least  3
0 minutes,   by   driving   or   with   the   vehicle  
s

tationary, so that the battery reaches an
adequate
  state   of   charge.
Some
  functions,   including   Stop   &   Start,  
a

re not available if the battery is not
sufficiently
 c

harged.
In the event of a breakdown

216
Do not force the lever as locking will not   be   possible   if   the   clamp   is   not  
p

ositioned   correctly;   start   the   procedure  
ag

ain.
Quick release terminal
Disconnecting the (+) terminal
F Raise the lever A fully to release the clamp  B.
The
  Stop   &   Start   system   may   not   be  
o

perational   during   the   trip   following   the  
f

irst   engine   start.
In
  this   case,   the   system   will   only   be  
a

vailable   again   after   a   continuous  
p

eriod   of   immobilisation   of   the   vehicle,  
a

  period   which   depends   on   the   ambient  
t

emperature   and   the   state   of   charge   of  
t

he   battery   (up   to   about   8   hours).
It
 
is
 
recommended
 
that
 
the
 
battery
 
be
 
d

isconnected
 
if
 
the
 
vehicle
 
is
 
not
 
to
 
be
 
used
 
f

or
 
a
 
very
 
long
 
period,
 
so
 
as
 
to
 
maintain
 
an
 
a

dequate
 
state
 
of
 
charge
 
for
 
starting
 
the
 
e

ngine.
Before
 
disconnecting
 
the
 
battery:
F
 
c

lose
 
all
 
openings
 
(doors,
 
boot,
 
windows,
 
r

oof),
F
 
s

witch
 
off
 
all
 
electrical
 
consumers
 
(audio
 
s

ystem,
 
wipers,
 
lighting...),
F
 
s

witch
 
off
 
the
 
ignition
 
and
 
then
 
wait
 f
our minutes.
At
 
the
 
battery,
 
simply
 
detach
 
the
 
(+)
 
terminal.
Disconnecting the battery
Following reconnection of the battery, switch on t
he   ignition   and   wait   1   minute   before   starting   to  
p

ermit   initialisation   of   the   electronic   systems.  
H

owever,   if   problems   remain   following   this  
o

peration,   contact   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Referring
  to   the   corresponding   section,   you  
m

ust
 y
ourself
 r
einitialise
 (
depending
 o
n
 ve

rsion):
-
 
t
he   remote   control   key,
-
 ...
Following reconnection of the battery
Reconnecting the (+) terminal
F Position   the   open   clamp   B of the cable on
the   positive   post   (+)   of   the   battery.
F
 
P
ress   down   on   the   clamp   to   position   it  
c

orrectly   on   the   battery   post.
F
 
L
ock   the   clamp   by   lowering   the   lever   A.
In the event of a breakdown

251
Level 1Level 2 Level 3 Comments
Navigation Settings
Navigation Enter destination
Display
  recent   destinations.
Route settings Fastest
Choose
  the   navigation   criteria.
The
  map   displays   the   route   chosen   according   to  
t

hese
 c
riteria.
Shortest
Time/distance
Ecological
To l l s
Ferries
Strict-Close
Show
  route   on   map Display   the   map   and   start   navigation.
Confirm Save
  the   options.
Save Save
  the   current   address.
Stop navigation Delete
  the   navigation   information.
Voice Choose
  the   volume   for   voice   and   announcement  
o

f   street   names.
Diversion Detour
  from   your   initial   route   by   a   certain  
di

stance.
Navigation Display
  in   text   mode.
Zoom
  in.
Zoom
  out.
Display
  in   full   screen   mode.
Use
  the   arrows   to   move   the   map.
Switch
  to   2D   map.
.
Audio and Telematics

258
Navigation - Guidance
Choosing a new destination
Select "Enter destination ". Select "
Save"   to   save   the   address  
e

ntered   as   a   contact   entry.
The   system   allows   up   to   200   entries.
Select " Confirm ".
Press " Show route on map " to start
navigation.
Select "
Address ".
Select the " Country:"
  from   the  
l

ist   offered,   then   in   the   same  
w

ay the "City:" or its post
code,
  the   "Road: ", the " N°:".
Confirm
  each   time. Select "
Navigate to ".
Choose   the   restriction   criteria:  
"T

o l l s", "Ferries ", "Tr a f f i c ", "Strict ",
" Close ".
Choose
  the   navigation   criteria:  
"F

astest" or "Shortest " or "Time/
distance " or "Ecological". To
  delete   navigation   information,  
p

ress "
Settings ".
Press " Stop navigation ".
To   resume   navigation  
p

ress "Settings ".
Press " Resume guidance ".
Press on Navigation
 

to   display   the  
p

rimary
 pag
e.
Press   on   the   secondary   page.
Towards a new destination
Or
Audio and Telematics

277
Level 1Level 2 Level 3 Comments
Telephone
connection
Secondary page Bluetooth
connection Search
Start
  the   search   for   another   peripheral   device   to  
c

onnect.
Disconnect Stop
  the   Bluetooth   connection   to   the   selected  
p

eripheral
 d
evice.
Update Import
  the   contacts   from   the   selected   telephone  
t

o   store   them   in   the   audio   system.
Delete Delete
  the   selected   telephone.
Confirm Save
  the   settings.
Telephone
conn ection
Secondary page Search
for devices Devices detected
Telephone
Start
  the   search   for   peripheral   devices.
Audio
 s

treaming
Internet
Telephone
connection
Secondary page
Telephone Options Put on hold
Cut
  the   microphone   temporarily   so   that   the  
c

ontact cannot hear your conversation with a
passenger.
Update Import
  the   contacts   from   the   selected   telephone  
t

o   save   them   in   the   audio   system.
Ringtones Choose
  the   telephone   ringtone   and   volume.
Memory info. Contact
  records   used   and   free,   percentage   of  
s

torage   space   used   by   internal   contacts   and  
Bl

uetooth
 c
ontacts.
Confirm Save
  the   settings.
.
Audio and Telematics