2016 Citroen C4 CACTUS lock

124
Key left in the "Ignition on"
position
If the key has been left in the ignition switch at position 2 (Ignition on) ,
the
  ignition   will   be   switched   off  
a

utomatically   after   one   hour.
To
  switch   the   ignition   back   on,   turn   the  
k

ey   to   position   1 (Stop),
  then   back   to  
p

osition 2 (Ignition on) .
Never
 
switch
 
off
 
the
 
ignition
 
before
 
the
 
v

ehicle
 
is
 
at
 
a
 
complete
 
stop.
With
 
the
 
engine
 
off,
 
the
 
braking
 
and
 
s

teering
 
assistance
 
systems
 
are
 
also
 
c

ut
 
off:
 
risk
 
of
 
loss
 
of
 
control
 
of
 
the
 
v

ehicle.
When
 
you
 
leave
 
the
 
vehicle,
 
keep
 
the
 
k

ey
 
with
 
you
 
and
 
lock
 
the
 
vehicle.
To facilitate unlocking of the steering c olumn,   it   is   recommended   that   the  
w

heels   be   returned   to   the   straight   ahead  
p

osition   before   switching   off   the   engine.
Switching off
F Stop  the   vehicle.
F  W ith   the   engine   running   at   idle,   turn   the   key  
t

o position 1 .
F
 
R
emove   the   key   from   the   ignition   switch.
F
 
T
o   lock   the   steering   column,   turn   the  
s

teering   until   it   locks.
F
 
C
heck   that   the   parking   brake   is   correctly  
a

pplied,   particularly   on   sloping   ground.For
  more   information,   refer   to   the  
"

Energy   economy   mode"   section.Energy economy mode
After switching off the engine (position 1- Stop),
for   a   maximum   of   30   minutes   you   can   still   use  
f

unctions   such   as   the   audio   and   telematic  
s

ystem,   the   wipers,   dipped   beam   headlamps,  
c

ourtesy   lamps, ...
Driving

181
Recommendations on storage
Never store bottles of AdBlue® in your
vehicle.
Procedure
F Switch   off   the   ignition   and   remove   the   key.
F  
F
or   access   to   the   AdBlue
® tank, raise the b
oot
 
carpet
 
then,
 
depending   on   equipment,  
l

ift
 
out
 
the
 
spare
 
wheel
 
and/or   the  
s

torage box. F
 
W
ithout   pressing,   turn   the   black   cap   a  
q

uarter   turn   anti-clockwise   and   lift   it   off.
AdBlue
® freezes at about -11°C and d
eteriorates   above   25°C.   It   is   recommended  
t

hat
 
bottles   be   stored   in   a   cool   area   and  
p

rotected   from   direct   sunlight.
Under
 
these   conditions,   the   additive   can   be  
k

ept
 
for
 
at   least   a   year.
If
 
the
 
additive   has   frozen,   it   can   be   used   once   it  
h

as
 
completely   thawed   out. Before
  topping-up,   ensure   that   the   vehicle   is  p
arked   on   a   flat   and   level   sur face.
In
  wintry   conditions,   ensure   that   the  
t

emperature   of   the   vehicle   is   above   -11°C.  
O

therwise
 t
he
 A
dBlue
® may be frozen and s
o
 
cannot
 
be
 
poured
 
into   its   tank.   Park   your  
v

ehicle
 
in
 
a
 
warmer
 
area   for   a   few   hours   to  
a

llow
 
the
 
top-up
 
to
 
be
 
carried   out.
F
 
T
urn   the   blue   cap   a   6
th of a turn anti-
c
lockwise.
F
 
L

ift
 
off
 
the
 
cap.
7
Practical information

182
F Obtain  a   bottle   of   AdBlue®. After first c
hecking
 
the
 
use-by
 
date,
  read   carefully  
t

he instructions on use on the label before
pouring
 
the
 
contents
 
of
 
the   bottle   into   your  
v

ehicle's
 Ad

Blue
® tank.
I
mportant :
 
if
 
your   vehicle's   AdBlue
®
tank
 
is
 
completely
 
empty
 
-
 
which
 
is
 
c

onfirmed
 
by
 
the
 
alert
 
messages
 
and  
t

he
 
impossibility
 
of
 
starting
 
the
 
engine,  
y

ou
 
must
 
add
 
at
 
least
 
3.8
 
litres
 
(so
 
t

wo 1.89
 
litre
 
bottles). If
  any   additive   is   split   or   splashed,   wash  
i

mmediately  
w
ith  
c
old  
w
ater  
o
r  
w
ipe  
w
ith  
a

  damp   cloth.
If   the   additive   has   crystallised,   clean   it  
o

ff   using   a   sponge   and   hot   water.Important:
 i
n the event of a top-up
after a breakdown because of a lack
of additive ,   signalled   by   the   message
 "

Top   up   emissions   additive:   Starting
 p

revented",   you   must   wait   around
 5

 minutes
 
before
 
switching
 
on
 
the
 
ignition,
 w

ithout opening the driver's door,
locking the vehicle or introducing the
key into the ignition switch .
Switch   on   the   ignition,   then,   after
 1

0 seconds,   start   the   engine.
Never   dispose   of   AdBlue
® additive b
ottles
 
in
 
the
 
household
 
waste.   Place  
t

hem
 
in
 
a
 
special
 
container   provided  
t

his
 p

urpose
 o

r
 t

ake
 t

hem
 t
o
 y
our
 d
ealer.
F
 
A

fter
 
emptying
 
the
 
bottle,
 
wipe
 
away
 
any
 
s

pillage
 
around
 
the
 
tank
 
filler
 
using
 
a
 
damp
 
c

loth.
F
 
R

efit
 
the
 
blue
 
cap
 
to
 
the
 
tank
 
and
 
turn
 
it
 
a
 
6th of a turn clockwise, to its stop.
F
 R
efit   the   black   cap   and   turn   it   a   quarter   of  
a

 
turn   clockwise   without   pressing.   Ensure  
t

hat   the   indicator   on   the   cap   lines   up   with  
t

he   indicator   on   the   support.
F
 
D

epending   on   equipment,   return   the   spare  
w

heel   and/or   the   storage   box   to   the   bottom  
o

f
  the   boot.
F
 
R

efit   the   boot   carpet   and   close   the   tailgate.
Practical information

194
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not block   traffic:   the   ground   must   be   level,  
s

table   and   not   slippery.
Apply
  the   parking   brake,   switch   off   the  
i

gnition   and   engage   first   gear   to   block  
t

he   wheels.
Check
  that   the   parking   brake   warning  
l

amps   in   the   instrument   panel   come   on.
The
  occupants   must   get   out   of   the  
v

ehicle   and   wait   where   they   are   safe.
Ensure
  that   the   jack   is   correctly  
p

ositioned   at   one   of   the   vehicle's  
j

acking   points.
Incorrect
  use   of   the   jack   could   cause  
t

he   vehicle   to   drop.
Never
  go   underneath   a   vehicle   raised  
u

sing   a   jack;   use   an   axle   stand.
List of operations
F Remove  the   wheel   bolt   cover(s)   using   the  t
ool 3   (depending   on   version).
F
 
S
lacken   the   bolts   using   the  
w

heelbrace

1 o n l y.
Do
  not   use:
-
 
t
he   jack   for   any   other   purpose   than  
l

ifting   the   vehicle,
-
 
a
  jack   other   than   the   one   supplied  
b

y   the   manufacturer. The
  jack   must   only   be   used   to   change   a  
w

heel   with   a   damaged   tyre.
The   jack   does   not   require   any  m
aintenance.
The
  jack   conforms   to   European  
l

egislation,   such   as   defined   in   the  
M

achinery   Directive   2006/42/CE.
In the event of a breakdown

200
Main beam headlamps
F Remove  the   protective   cover   by   pulling  t
he tab.
F
 
D
isconnect   the   bulb   connector   (do   not  
r

emove
 t
he
 e
arth
 c
onnector
 lo
cated
 belo
w).
F
 
P
ush   on   the   spring,   then   move   it   towards  
t

he   middle   of   the   vehicle   to   release  
t

he bulb.
F
 
R
emove   the   bulb   and   change   it.
Direction indicators
Amber coloured bulbs, such as the direction   indicators,   must   be   replaced  
w

ith   bulbs   of   identical   specifications  
a

nd   colour.
Rapid
 
flashing
 
of
 
the
 
direction
 
indicator
 w
arning
 
lamp
 
(right
 
or
 
left)
 
indicates
 
the
 
f

ailure
 
of
 
a
 
bulb
 
on
 
that
 
side.
F
 
T

urn
 
the
 
bulb
 
holder
 
an
 
eighth
 
of
 
a
 
turn
 
a

nti-clockwise
 
and
 
extract
 
it.
F
 
R

emove
 
the
 
bulb
 
and
 
change
 
it.
To
 
reassemble,
 
carry
 
out
 
these
 
operations
 
in
 
r

everse
 o

rder. To
 
reassemble,
 
carry
 
out
 
these
 
operations
 
in
 
r

everse
 o

rder.
In the event of a breakdown

203
1. Sidelamps (W5W).
2. B rake   lamps   (P21W).
3.
 D

irection   indicators   (PY21W).
4.
 F

oglamp   or   reversing   lamp   (P21W).
Rear lamps
Changing bulbs
To reassemble, carry out these operations in reverse o rder.
F
 
S
pread   the   bulb   holder   retainers   and  
r

emove   the   bulb   holder.
F  
R
eplace   the   failed   bulb:
-  
f
or   the   sidelamp,   pull   the   bulb   (the   upper  
o

n e) o u t ,
-  
f
or   the   other   lamps,   turn   the  
c

orresponding   bulb   (lower)   a   quarter  
t

urn.
These
 
bulbs
 
are
 
changed
 
from
 
inside
 
the
 
boot.
F
 
O

pen
 
the
 
boot.
F
 
R

emove
 
the
 
corresponding
 
access
 
cover
 
in
 
t

he
 
trim
 
panel.
F
 
D

isconnect
 
the
 
lamp
 
unit
 
connector
 
a by
pressing
 
the
 
locking
 
button
 
(located
 
under
 
t

he
 
connector
 
for
 
the
 
right
 
hand
 
lamp
 
a

nd
 
above
 
the
 
connector
 
for
 
the
 
left
 
hand
 lam
p).
F
 S
lacken
 
and
 
remove
 
the
 
nut
 
b ( take care
not to drop it inside the wing ).
F
 
P

ress
 
down
 
on
 
the
 
retaining
 
clip
 
for
 
lamp
 
u

nit c,
 
then
 
carefully
 
remove
 
it
 
towards
 
the
 
o

utside. Take
  care   to   engage   the   lamp   unit   in   its  
g

uides,   while   keeping   it   in   line   with   the  
v

ehicle.
Tighten
  sufficiently   to   ensure   sealing,  
b

ut   without   damaging   the   lamp.
8
In the event of a breakdown

209
FuseN° Rating
(A) Functions
F19 5Seat
  belt   unfastened   warning.
F20 5Airbags.
F21 5Instrument
  panel.
F22 30Locks.
F23 5Courtesy
  lamp.   map   reading   lamp.
F26 15Horn.
F27 15Front
  and   rear   screenwash.
F28 5Ignition
 s

witch.
F30 15Rear wiper
8
In the event of a breakdown

216
Do not force the lever as locking will not   be   possible   if   the   clamp   is   not  
p

ositioned   correctly;   start   the   procedure  
ag

ain.
Quick release terminal
Disconnecting the (+) terminal
F Raise the lever A fully to release the clamp  B.
The
  Stop   &   Start   system   may   not   be  
o

perational   during   the   trip   following   the  
f

irst   engine   start.
In
  this   case,   the   system   will   only   be  
a

vailable   again   after   a   continuous  
p

eriod   of   immobilisation   of   the   vehicle,  
a

  period   which   depends   on   the   ambient  
t

emperature   and   the   state   of   charge   of  
t

he   battery   (up   to   about   8   hours).
It
 
is
 
recommended
 
that
 
the
 
battery
 
be
 
d

isconnected
 
if
 
the
 
vehicle
 
is
 
not
 
to
 
be
 
used
 
f

or
 
a
 
very
 
long
 
period,
 
so
 
as
 
to
 
maintain
 
an
 
a

dequate
 
state
 
of
 
charge
 
for
 
starting
 
the
 
e

ngine.
Before
 
disconnecting
 
the
 
battery:
F
 
c

lose
 
all
 
openings
 
(doors,
 
boot,
 
windows,
 
r

oof),
F
 
s

witch
 
off
 
all
 
electrical
 
consumers
 
(audio
 
s

ystem,
 
wipers,
 
lighting...),
F
 
s

witch
 
off
 
the
 
ignition
 
and
 
then
 
wait
 f
our minutes.
At
 
the
 
battery,
 
simply
 
detach
 
the
 
(+)
 
terminal.
Disconnecting the battery
Following reconnection of the battery, switch on t
he   ignition   and   wait   1   minute   before   starting   to  
p

ermit   initialisation   of   the   electronic   systems.  
H

owever,   if   problems   remain   following   this  
o

peration,   contact   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Referring
  to   the   corresponding   section,   you  
m

ust
 y
ourself
 r
einitialise
 (
depending
 o
n
 ve

rsion):
-
 
t
he   remote   control   key,
-
 ...
Following reconnection of the battery
Reconnecting the (+) terminal
F Position   the   open   clamp   B of the cable on
the   positive   post   (+)   of   the   battery.
F
 
P
ress   down   on   the   clamp   to   position   it  
c

orrectly   on   the   battery   post.
F
 
L
ock   the   clamp   by   lowering   the   lever   A.
In the event of a breakdown