2016 Citroen C1 RHD tow

67
Rear parcel shelf
To facilitate loading of the boot, the rear parcel shelf   is   fitted   to   the   tailgate.
When
  closing   the   tailgate,   check   that   nothing  
c

ould   inter fere   with   the   return   to   position   of  
t

he shelf.
Do
  not   place   heavy   loads   on   the   shelf,  
a

s   they   may   cause   the   shelf   to   unclip.
To
  remove   the   shelf:
F
 
o
pen   the   tailgate,
F
 
u
nclip   the   two   cords,
F
 
p
ull   firmly   on   the   shelf   to   disengage   it   from  
i

ts   hinges   on   the   tailgate   inner   trim.
You
  can   then   stow   the   shelf   behind   the   front  
sea

ts.To
  refit   the   shelf:
F
 
o
pen   the   tailgate,
F
 
p
osition   the   underside   of   the   shelf   facing  
yo

u,
F
 
c
lip   the   shelf   into   the   two   hinges,
F
 
p
ass   the   two   cords   through   the   guides  
e

ither   side   of   the   struts,
F
 
c
lip   the   two   cords   in   place.
3
Ease of use and comfort

69
Storage box
F Remove  the   boot   carpet   for   access   to   the  s
torage   box.
Depending
  on   the   configuration,   it   is   laid   out   for  
s

toring:
-
 
a
  towing   eye,
-
 
a
  temporary   puncture   repair   kit,
-
 ...
F

or   versions   with   storage   box:   it   must  
b

e   in   place   before   loading   the   boot.
The
 
hooks
 
can
 
be
 
used
 
to
 
secure
 
shopping
 b
ags.
Hooks
Maximum authorised load on the 
h ooks: 2 k g.
3
Ease of use and comfort

72
If you use the ancillaries for a prolonged period,   the   vehicle   will   automatically  
s

witch to " OFF"
  mode   after   about  
2

0 minutes.
Be aware
 

in   order   to   avoid   discharging  
t

he   battery.
Starting - switching off the engine 
w ith   the   Keyless   Entry   and   Starting  
system
Changing the mode of the
vehicle
With the electronic key inside the v
ehicle;   each   press   on   the   "S TA R T/
STOP " button, with no action on the
pedals,
  changes   the   vehicle's   mode:
F
 
F

irst
 
press   ("ACC "
  mode).
 T

he
 
ancillaries   (radio,   12V   socket...)   can  
be
 
used.
F
 
S

econd   press   ("ON "
  mode).
 I

gnition   on.
F
 
T

hird
 
press   ("OFF "
  mode).
Avoid
 
attaching
 
heavy
 
objects
 
to
 
the
 k
ey,
 
which
 
would
 
weigh
 
down
 
on
 
its
 
b

lade
 
in
 
the
 
ignition
 
switch
 
and
 
could
 
c

ause
 
a
 
malfunction.
F
 
I

mmobilise
 
the
 
vehicle.
Switching off
F With
  a   manual   gearbox:   put   the   gear   lever  i
nto   neutral.
F
 
W
ith   an   ETG   gearbox:   place   the   selector   at  
p

osition N .
F
 
T
urn   the   key   towards   you   to   position   2 (ACC).
F

Press in and turn the key to position 1 (LOCK) .F Remove   the   key   from   the   ignition   switch.
F  T urn   the   steering   until   the   steering   column  
l

ocks.
Driving

86
The speed limiter cannot, in any circumstances,   replace   the   need   to o

bserve   speed   limits,   nor   can   it   replace   the
 n

eed   for   vigilance   on   the   part   of   the   driver.
Speed limiter (PureTech 82 engine)
The speed limiter is switched on  manually: t
his   can   be   done   whatever   the   speed   of   the  
v

ehicle.   However,   if   you   are   driving   at   less   than  
2

0   mph   (30   km/h),   the   programmed   speed   will  
b

e   fixed   at   20   mph   (30   km/h).
The
  speed   limiter   is   paused by operation of the
control.
The
  programmed   speed   can   be   exceeded  
t

emporarily   by   pressing   the   accelerator   firmly  
b

eyond   the   point   of   resistance.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal   until   the   vehicle  
r

eturns   to   the   programmed   speed   limit.
System
  which   prevents   the   vehicle   from   exceeding   the   speed   programmed   by   the   driver.Steering mounted controls
The controls are grouped together on this c
ontrol   stalk   at   the   steering   wheel.
1.
 S

peed   limiter   on   /   off:   by   pressing   the   end  
o

f   the   control   stalk.
2.
 D

ecrease   the   setting:   by   pushing   the  
c

ontrol   stalk   down.
3.
 I

ncrease   the   setting:   by   pushing   the   control  
s

talk   up.
4.
 S

peed   limiter   on   /   pause:   by   pulling   the  
c

ontrol   stalk   towards   you.
Displays in the instrument panel
The information is grouped together in the instrument   panel   screen.
5.
 S

peed   limiter   mode   selection   indication.
6.
 S

peed   limiter   on   /   pause   indication.
7.
 S

peed   value   setting.
The
 
programmed
 
speed
 
remains
 
in
 
the
 m

emory
 
when
 
the
 
ignition
 
is
 
switched
 
off.
Driving

87
Switching on
F Press  the   end   of   the   control   stalk:   the  s
peed   limiter   mode   is   selected   but   is   not  
s

witched   on.
F
 
S
witch   the   speed   limiter   on   by   pulling   the  
c

ontrol   stalk   towards   you,   if   the   speed  
d

isplayed   is   suitable   (by   default,   the   last  
s

peed
 pro
grammed). Once
  the   function   is   selected,   you   can   modify  
t

he   speed   setting   by:
-  
b
y   pushing   the   control   stalk   up   to   increase  
t

he
 se
tting,
-  
b
y   pushing   the   control   stalk   down   to  
d

ecrease
 t
he
 se
tting.
A   brief   push   on   the   control   stalk   modifies   the  
s

peed   setting   by   +   or   -   1   mph   (km/h).
A   maintained   push   on   the   control   stalk   modifies  t
he   speed   setting   by   +   or   -   5   mph   (km/h).
Adjusting the speed limit
setting
You do not have to switch the speed l
imiter   on   in   order   to   set   the   speed.
Pause
F You  can   temporarily   stop   the   speed   limiter  b
y   pulling   the   control   stalk   towards   you  
a

gain:   the   display   confirms   that   it   has   been  
s

topped
 (
Pause).
F
 
P
ull   the   control   stalk   towards   you   again   to  
r

estore   the   speed   limiter.
4
Driving

89
Speed limiter (VTi 68 engine)
System which prevents the vehicle from exceeding the speed programmed by the driver.
T he   speed   limiter   is   switched on
 m
anually:
 t

his   can   be   done   whatever   the   speed   of   the  
v

ehicle.   However,   if   you   are   driving   at   less   than  
2

0   mph   (30   km/h),   the   programmed   speed   will  
b

e   fixed   at   20   mph   (30   km/h).
The
  speed   limiter   is   paused by operation of the
control.
The
  programmed   speed   can   be   exceeded  
t

emporarily   by   pressing   the   accelerator   firmly  
b

eyond   the   point   of   resistance.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal   until   the   vehicle  
r

eturns   to   the   programmed   speed   limit.
The
  programmed   limit   speed   is   erased  
w

hen   switching   off   the   ignition.
Steering mounted controls
The controls are grouped together on this control   stalk   at   the   steering   wheel.
1.
 S

peed   limiter   on   /   off:   by   pressing   the   end  
o

f   the   control   stalk.
2.
 P

rogramming   the   speed
 D

ecrease   the   setting:   by   pushing   the  
c

ontrol   stalk   down.
3.
 R

estore   speed   limiter
 I

ncrease   the   setting:   by   pushing   the   control  
s

talk   up.
4.
 P

ause   speed   limiter:   by   pulling   the   control  
s

talk   towards   you.
Displays in the instrument panel
The information is grouped together in the instrument   panel   screen.
5.
 S

peed   limiter   on   /   pause   indication.
6.
 S

peed   value   setting.
The speed limiter cannot, in any circumstances,   replace   the   need   to   observe s

peed   limits,   nor   can   it   replace   the   need   for
 v

igilance   on   the   part   of   the   driver.
If you choose to display other information (trip  A
  for   example),   the   speed   limiter  
i

nformation   is   automatically   displayed   again  
a

fter   about   6   seconds.
4
Driving

90
F Press  the   end   of   the   control   stalk:   the  s
peed   limiter   is   switched   on.
F
 
A
ccelerate   or   decelerate   to   attain   the  
de

sired
 s
peed.
F
 
P
ush   the   control   stalk   down   and   release,   to  
p

rogramme   the   speed.
 T

he   speed   at   which   the   vehicle   is   running  
a

t   the   moment   when   you   release   the  
c

ontrol   stalk   becomes   the   programmed  
s

peed.
Adjusting the speed limit
setting
Once a speed is programmed, you can modify it   by   pushing   and   releasing   the   control   stalk:
-
 
u
p   to   increase   the   speed   setting,
-
 
d
own   to   reduce   the   speed   setting.
A
  brief   push   on   the   control   stalk   modifies   the  
s

peed   setting   by   +   or   -   1   mph   (km/h).
A
  maintained   push   on   the   control   stalk   modifies  
t

he   speed   setting   by   +   or   -   5   mph   (km/h).
Switching on
This indicator lamp comes on in the instrument pan el.
Pause
F You  can   temporarily   stop   the   speed   limiter  b
y   pulling   the   control   stalk   towards   you.
F
 
P
ush   the   control   stalk   up   to   restore  
o

peration   of   the   speed   limiter   with   the  
s

ame   speed   setting.
Driving

99
Model without AUTO lighting
Model with AUTO lightingSelection ring for main lighting
mode
Turn the ring to position the symbol required f
acing   the   mark.
Lighting
  off   /   Daytime   running   lamps.
Sidelamps
 o

nly.
Dipped
  or   main   beam   headlamps.
Automatic
  illumination   of  
h

eadlamps.
Dipping the headlamps
With dipped beam on, push the control stalk away   from   you   to   change   to   main   beam.   Pull  
t

he   stalk   toward   you   change   back   to   dipped  
b

eam.
In
  the   lighting   off   and   sidelamps   modes,   the  
d

river   can   switch   on   the   main   beam   headlamps  
t

emporarily   ("headlamp   flash")   by   maintaining   a  
p

ull   on   the   stalk.
Displays
Illumination of the corresponding indicator lamp in   the   instrument   panel   confirms   the   lighting  
s

witched   on.
5
Lighting and visibility