2016 Citroen BERLINGO MULTISPACE warning

166
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
AdBlue®
Once the 350 miles (600 km) threshold is  reached,   the   UREA  warning   lamp  
flashes

  and   the   Service   warning   lamp  
comes

  on,   accompanied   by   a   message  
on

  the   remaining   driving   range.
The alert is repeated every 30 seconds
with
  an   update   of   the   remaining   driving  
range

  in   steps   of   30   miles   (50   km)  
travelled.
Every

  time   the   ignition   is   switched  
on, the alert is given together with an
audible

  signal.
At 0 miles the system installed in
the vehicle to meet the emissions
standard will prevent engine
starting. The
  0   fluid   level   has   been   reached.
Your   vehicle's   exhaust   emissions   no  
longer

  meet   the   "Euro   6"   standard   and  
the

  engine   will   not   start.
To be able to restart the vehicle, you
must   add   at   least   4 litres of a dBlue
®.
-
 
Pour

 
the
 
additive
 
into
 
the
 
tank
 
(by  
the

 
filler
 
with
 
the
 
blue
 
cap).
-

Switch on the ignition without
starting.
-


W

ait 10 seconds before starting the
engine.
Remaining range less than 350 miles
(600 km) and more than 0 miles
Starting prevented, breakdown
related to a lack of AdBlue
® in the
special tank
Avoid waiting until the
remaining range is 0 miles!
The alert is repeated when driving until
the
a
dBlue
® tank has been topped-up with
 
sufficient   additive.
Unless the additive in the special
additive
 
tank   is   topped-up,   you   risk  
immobilisation

  of   the   vehicle. Following
  this,   make   a   further   fill  to
  the   special   additive   tank,   the  
capacity of which is

17 litres.
Fault with the SCR system
The UREa, Service and diagnostic
warning   lamps   comes   on.
Every
  time   the   ignition   is   switched   on,  
the

  emissions   fault   is   confirmed   by   an  
audible

  signal   and   a   message.
If
  it   is   a   temporary   fault,   the   alert  
disappears as soon as the exhaust
emissions

  return   to   the   levels   required  
by

  the   standard.
Detection
o

n the other hand, if the warning
lamps
  are   still   on   after   30   miles  
(50

  km)   of   driving,   the   fault   is  
confirmed.
An

  engine   start   prevention   system  
will

  be   activated   automatically   after  
650 miles

  (1   100   km)   travelled  
following

  this   confirmation.
Go
  to   a   CITROËN   dealer   or   a   qualified  
workshop.
o

r go to a CITR
o
Ë
n
dealer or a
qualified
 
workshop.

 167
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
AdBlue®
Fault confirmed
In addition to the previous signals,
the  UREA
 
warning   lamp   flashes   and  
the

  remaining   range   allowed   will   be  
displayed

  in   miles   (kilometres).
The alert will be repeated every
30
seconds with an update of the
driving
  range   in   steps   of   30   miles  
(50 km).
Go

  to   a   CITROËN   dealer   or   a   qualified  
workshop

  as   soon   as   possible.
You
  risk   not   being   able   to   start   the  
engine.
Starting prevented, having
covered the 650 miles (1 100 km)
At

  each   attempt   at   starting,   the   alert   is  
activated

  and   the   message   "Emissions  
fault:

  Starting   prevented"   is   displayed.Refilling / Topping-up the
AdBlue®
Precautions to take
Use only a dBlue® that meets the ISO 22241
 
standard.
The
a
dBlue
® fluid is an urea-based solution.
This
 
fluid
 
is
 
non-flammable,   colourless  
and

 
odourless.
To
 
be
 
kept
 
in   a   cool   area.
Containers (5 or 10 litres) and
bottles (1.89 litres) of AdBlue
®
Please check the use-by date.
Read   the   instructions   on   the   label.
Ensure that you have a suitable
filler
  pipe,   which   may   or   may   not   be  
supplied

  with   the   container. In
  the   event   of   an   overflow,   wipe  
around

  the   filler   mouth   using   a  
damp

  cloth.
If any a dBlue
® fluid is split or splashed
 
on
 
to
 
you,   wash   immediately  
with cold water or wipe yourself with a
clean

 
damp
 
cloth.
If
 
the
 
fluid
 
has
 
crystallised,   clean   it   off  
using

 
a
 
sponge
 
and   hot   water.
CHECKS
7

168
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Filling
Ensure that the vehicle is parked on a flat  and   level   surface.
Pour
  the   contents   of   the   container   /  
bottle

  into   the   dedicated   tank.
After
  filling   the  
AdBlue® tank, observe the
 
following
 
procedure:
-

Switch on the ignition without
starting.
-


W

ait 10 seconds before starting the
engine.
Never
 
dispose
 
of
 
empty  
AdBlue®
containers and bottles in the
household
 
waste.
Place
 
them
 
in
 
a
 
special
 
container
 
provided

 
this
 
purpose
 
or
 
take
 
them
 
to  
your

 
dealer.
k
eep a dBlue
® out of the reach of
children,
 
in
 
its
  original   container.
n

ever transfer a dBlue
® to another
container:
 
it
 
would
 
loose
 
its
  purity.
Never
 
dilute
 
the
 
fluid
 
with
 
water.
Never
 
pour
 
the
 
fluid
 
into
 
the   Diesel   fuel  
tank.
Recommendations on storage
never store containers or bottles of adBlue® in your vehicle.
Freezing of the AdBlue
®
adBlue® freezes at about -11°C (12.2° F) and
 
deteriorates   above   25°C   (77°F).
It
 
is
 
recommended   that   containers   and  
bottles be stored in a cool area and
protected

  from   direct   sunlight.
Under
 
these   conditions,   the   fluid   can  
be

 
kept
  for   at   least   a   year.
a

dditive that has been frozen can
be used once it has thawed out in
ambient air. The
  SCR   system   includes   an  
a dBlue
® tank heater that ensures operation
  of   the   vehicle   in   normal  
conditions.
In exceptional situations, such
as

 
when
 
the
 
vehicle   is   kept   at  
temperatures

  below   -15°C   (5°F)   for   a  
long

 
period,
 
there   may   be   an   emission  
fault alert related to freezing of the a

dBlue
® additive.
Park
 
the   vehicle   in   an   area   at   a   more  
moderate

  temperature   for   a   few   hours  
until

the a dBlue
® becomes a fluid again.
The
 
emissions
 
warning   lamp   does   not  
go

 
off
 
immediately,   but   does   so   after   a  
few

 
miles
 
of
 
driving.
adBlue®

170
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
ECONOMY MODE
after the engine has stopped, with
the   key   in   the   ignition   position,   certain  
functions (windscreen wiper

, electric
windows,
  courtesy   lamps,   audio  
equipment,

  etc.)   can   only   be   used   for   a  
cumulative

  duration   of   thirty   minutes,   to  
prevent

  discharging   of   the   battery.
Once
  the   thirty   minutes   have   elapsed,  
the active functions are put on standby
and

  the   battery   warning   lamp   flashes  
accompanied

  by   a   message   in   the  
screen.
T

o   resume   the   use   of   these   functions  
immediately

,   start   the   engine   and   let   it  
run

  for   a   few   minutes.
The
  time   available   will   then   be   double  
the

  time   for   which   the   engine   was   left  
running.

  However,   this   time   will   always  
be

  between   five   and   thirty   minutes.
A
 

flat   battery   will   prevent   the  
engine

  from   starting.
Battery

171
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
The temporary tyre repair kit consists of  a   compressor   and   a   bottle  
(containing

  a   sealant).
Using the kit
- Tick  the   deflated   wheel   on   the  speed
  limitation   sticker   then   affix  
the

  sticker   to   the   vehicle's   steering  
wheel

  to   remind   you   that   a   wheel   is  
in

  temporary   use.
-

Clip the bottle
1 on the
compressor 2.
-

Connect the bottle
1 to the valve of
the
  tyre   to   be   repaired.
-
 
T
ake   care   to   unwind   the  
compressor

  pipe   before   connecting  
it

  to   the   bottle.
-

Connect the power lead to one of
the

  vehicle's   12V   sockets.
-
 
Switch
  on   the   compressor   by  
pressing button

A until the tyre
pressure
  reaches   2.0   bars.   If   this  
pressure cannot be reached, the
tyre

  cannot   be   repaired.
-
 
Remove
  and   store   the   compressor.
-
 
Drive
  immediately,   for   a   few   miles  
(kilometres),

  at   reduced   speed,   to  
fill

  the   puncture.
-
 
Adjust
  the   pressure   using   the  
compressor

  in   accordance   with   the  
recommendation

 
for
 
the
 
vehicle
 
and
 
check

  that   the   leak   is   filled   correctly  
(no

  further   loss   of   pressure).
-
 
Drive
  at   reduced   speed   (50 mph  
[80

  km/h]).  
The
  tyre   must   be  
examined

  and   repaired   by   a  
specialist

  as   soon   as   possible.
a
fter use, the bottle can be stored in
a   plastic   bag,   supplied   in   the   kit,   to  avoid staining your vehicle with traces
of
  fluid.
Warning:
  the   sealant   product   is  
harmful

  if   swallowed   and   causes  
irritation

  to   the   eyes.
Keep
  it   out   of   reach   of   children.
a

fter use, do not discard the bottle into
the
  environment,   take   it   to   a   CITROËN  
dealer or to an specialised waste
disposal

  site.
Replacement
  bottles   of   sealant   are  
available

  from   CITROËN   dealers.
TEMPORARY PUNCTURE
REP

AIR KIT
The kit is located in one of the two storage   compartments   located  
under

  the   front   seats.
Vehicles
  supplied   with   a   temporary  
puncture

  repair   kit   do   not   have   a   spare  
wheel

  or   tooling   (jack,   wheelbrace,   ...).
QUICk HELP
8
Changing a wheel

Audio and Telematics
218
Berlingo-2-VP_en_Chap10a_SMEGplus_ed01-2016
Risk areas / Danger zone
alert settings
Press on Navigation to display the
primary pag e.
Press
  on   the   secondary   page.
Select " Settings ".
Select " Alarm!"
  (Alert).
It
 
is
 
then
 
possible   to   activate   Risk   areas   alerts  
t

hen:
-
"au

dible warning"
-
"al

ert only when navigating"
-

"al

ert only for overspeed"
-
 
"

Display   speed   limits"
-
 
T

iming:   the   choice   of   timing   allows   the  
t

ime
 
before   giving   a   Risk   areas   alert   to   be  
de

fined. Select " Confirm ". This series of alerts and displays is
only
  available   if   Risk   areas   have   first  
b

een downloaded and installed on the
system.
Tr a f fi c
Traffic information
Display of messages
Press on Navigation to display the
primary pag e.
Press
  on   the   secondary   page.
Select " Traffic messages ".
Choose
 
filter   settings   for:
" On the route ",
" Around ",
" Near destination ", filters to fine-
tune
  the   list   of   messages.
Press
 
again   to   remove   the   filter.

Audio and Telematics
262
Berlingo-2-VP_en_Chap10a_SMEGplus_ed01-2016
The table below gives answers to the most frequently asked questions on your audio system.
Q UESTION ANSWER SOLUTION
The route calculation is not
successful. The
  navigation   settings   may   conflict   with   the   current   location  
(

exclusion   of   toll   roads   on   a   toll   motor way).Check
  the   settings   in   the   "Navigation"   menu.
The
  POIs   do   not   appear. The   POIs   have   not   been   selected.Select
  the   POIs   in   the   list   of   POIs.
The
  Risk   areas   audible  
w

arning   does   not   work.The
  audible   warning   is   not   active.
ac
tivate audible warnings in the "
na
vigation"
menu.
The
  system   does   not  
s

uggest a detour around an
incident
  on   the   route.The
  guidance   criteria   do   not   take   account   of   TMC   messages. Select   the   "Information"   function   in   the   list   of  
g

uidance
 c
riteria.
I
  receive   a   Risk   areas   alert  
w

hich   is   not   on   my   route.Other
  than   guidance,   the   system   announces   all   Risk   areas  
p

ositioned   in   a   cone   located   in   front   of   the   vehicle.   It   may   provide   an  
a

lert   for   Risk   areas   located   on   nearby   or   parallel   roads.Zoom
  in   on   the   map   to   view   the   exact   position   of  
t

he   Risk   areas.   Select   "On   the   route"   to   no   longer  
r

eceive alerts other than guidance or to reduce
the
  time   for   the   announcement.
Frequently asked questions
Navigation

Audio and Telematics
282
Berlingo-2-VP_en_Chap10b_Rd45_ed01-2016
Screen C
Audio functions
alternative frequencies (RdS )
Activate   /   deactivate
FM
preferences
Regional   mode   (REG)
Activate
  /   deactivate
Radio-text
  information   (RDTXT)
Activate
  /   deactivate
1
2
3
4
3
4
3
4
Play modesAlbum   repeat   (RPT)
Activate
  /   deactivate
Track
  random   play   (RDM)
Activate
  /   deactivate2
3
4
3
4
Enter distance to destination1
1
1
2
2
2
Pressing the MENU  button   displays:
Audio functions Trip computerDistance: x miles
Vehicle diagnosis
Warning log
Systems activated or deactivated
State of systems