2016 Citroen BERLINGO MULTISPACE service

+ +
39
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
SCR emissions control system
Alerts InformationSolution - action
The   UREA,   Service   and   diagnostic   warning   lamps  
come

  on,   an   SCR   emissions   control   system   fault  
has

  been   detected. This
  is   is   temporary   fault,   the   alert   disappears   as  
soon

  as   the   exhaust   emissions   return   to   normal  
levels.
After 30 miles (50 km) without

AdBlue
®
Confirmation of the fault which is not related to a lack  of   fluid. The
  remaining   driving   range   700   miles  
(1   100   km).
Go   to   a   CITROËN   dealer   or   a   qualified   workshop  
as

  soon   as   possible   to   avoid   a   breakdown.
The
  fault   is   confirmed.
The
  next   time   the   ignition   is   switched   on,   the  
authorised

  driving   range   will   be   displayed   in   miles  
(kilometres)

  and   the   alert   will   be   repeated   every  
30
  seconds.
The
  limit   of   the   driving   range   has   been   reached,  
exhaust

  emissions   levels   are   above   the   limits.
Starting
  is   impossible. To restart the engine, you must contact a
CITROËN
  dealer   or   a   qualified   workshop.
- BlueHDi Diesel
READY TO GO
3

42
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controlsThe   alert   is   maintained   until  
the tyre or tyres concerned is
reinflated,

  repaired   or   replaced.
The spare wheel (space-saver type or
a
  steel   rim)   does   not   have   a   sensor.
Operating fault
Under-inflation alert
The loss of pressure detected
does not always lead to visible
deformation
 
of
 
the
 
tyre.
 
Do
 
not
 
rely
 
on

  just   a   visual   check.The alert is given by the fixed illumination  of   this   warning   lamp, accompanied

  by   an   audible   signal,
 and

  depending   on   equipment,   the
 display

  of   a   message.The flashing and then fixed  illumination   of   the  
under-inflation

  warning  
lamp

  accompanied   by   the  
illu

mination   of   the   "Service"   warning  
lamp,

 
and   depending   on   equipment,  
the

 
display   of   a   message   indicates   a  
fault

 
with   the   system.
In
 
this
 
case,   monitoring   of   the   tyre  
pressures

  is   not   assured.
In
 
the
 
event
 
of
 
a
 
problem
 
on
 
one
 
of
 
the

 
tyres,
 
the
 
symbol
 
or
 
the
 
message
 
appears,

 
according
 
to
 
equipment,
 
to
 
identify

 
it.
-

Reduce speed, avoid sudden
steering

 
movements
 
or
 
harsh
 
brake
 
applications.
-

 
Stop

 
as
 
soon
 
as
 
it
 
is
 
safe
 
to
 
do
 
so.
-

In the event of a puncture, use
the

 
temporary
 
puncture
 
repair
 
kit
 
or the spare wheel (according to
equipment),
or
-

 
if

 
you
 
have
 
a
 
compressor,
 
the
 
one
 
in

 
the
 
temporary
 
puncture
 
repair
 
kit

 
for
 
example,
 
check
 
the
 
four
 
tyre
 
pressures when cold,
or
-

 
if

 
it
 
is
 
not
 
possible
 
to
 
check
 
the
 
tyre

 
pressures
 
at
 
the
 
time,
 
drive
 
carefully

 
at
 
reduced
 
speed.
This alert is also displayed when
one
  or   more   wheels   is   not   fitted  
with

  a   sensor   (for   example,   a  
space-saver

  or   steel   spare   wheel).
Go
 
to
 
a   CITROËN   dealer   or   a   qualified  
workshop to

  have   the   system   checked  
or

, following the repair of a puncture, to
have the original wheel, equipped with
a
 
sensor,   refitted.

46
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
The new pressure settings registered
are considered to be reference values
by
  the   system. The
  under-inflation   alert   can   only  
be

  relied   on   if   the   system   has  
been reinitialised with all four tyres
inflated

  to   the   correct   pressures.
Before doing anything to the
system,
  the   pressures   of   the   four  
tyres

  must   be   checked   and   the  
system

  reinitialised.
Snow chains
The
  system   does   not   have   to   be  
reinitialised

  after   fitting   or   removing  
snow

  chains.
Dashboard button
F
 
Make
  a   long   press   on   this   button.
A
 

high   tone   audible   signal   confirms   the  
reinitialisation.
a low tone audible signal indicates that
the

  reinitialisation   was   not   completed.
Operating fault
The flashing and then fixed illumination of  the   under-inflation   warning   lamp  
accompanied

  by   illumination   of   the  
Service

  warning   lamp   indicates   a   fault  
with

  the   system.
In
  this   case,   under-inflation   monitoring  
of

  the   tyres   is   no   longer   assured.
Have
  the   system   checked   by   a  
CITROËN

  dealer   or   a   qualified  
workshop.

47
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
SERVICE INDICATOR
This programmes service intervals according  to   the   use   of   the   vehicle.More than 1 000 miles/km before the
next service is due
Example:
  4   800   miles/km   remain  
before

  the   next   service   is   due.   When  
the ignition is switched on and for a
few

  seconds,   the   screen   shows:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance

  recorder   resumes   normal  
operation showing the total and trip
distances.
Less than 1 000 miles/km before the
next service is due
Each time the ignition is switched on and for a few seconds,  the   spanner   flashes   and   the   number   of miles/kilometres

  remaining   is   displayed:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance
  recorder   resumes   normal  
operation

  and   the   spanner   remains   on.  
This indicates that a service should be
carried

  out   shortly.
Service overdue
Operation
A
 

few
 
moments
 
after
 
the
 
ignition
 
has been switched on, the spanner
indicating

 
a
 
service
 
operation
 
comes
 
on; the display for the total distance
recorder

 
gives
 
(in
 
round
 
figures)
 
the
 
distance

 
remaining
 
before
 
the
 
next
 
service.
The points at which a service is due
are

 
calculated
 
from
 
the
 
last
 
indicator
 
zero

 
reset.
The point at which a service is due is
determined
 
by
 
two
 
parameters:
-

the distance travelled,
-

 
the

 
time
 
which
 
has
 
elapsed
 
since
 
the

 
last
 
service.
The
 
distance
 
remaining
 
before
 
the
 
next

 
service
 
may
 
be
 
weighted
 
by
 
the

 
time
 
factor,
 
depending
 
on
 
the
 
type

 
of
 
driving. With the engine running the spanner
remains
  on   until   the   service   has   been  
carried

  out.
For BlueH
d i d iesel versions, this
alert
  is   also   accompanied   by   the   fixed  
illu

mination   of   the   Service   warning  
lamp,

  on   switching   on   the   ignition.
Each
  time   the   ignition   is  
switched on and for a few
seconds, the spanner
flashes

  and   the   excess  
distance

  is   displayed.
For BlueH
d i d iesel versions, the
spanner
  can   also   come   on   early,  
according the level of deterioration
of

  the   engine   oil.   Deterioration   of   the  
engine oil depends on the conditions of
use

  of   the   vehicle.
REadY To Go
3

48
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
Trip recorder zero
reset button
after this operation, if you wish to
disconnect   the   battery,   lock   the  
vehicle

  and   wait   for   at   least   five  
minutes,

  otherwise   the   zero   re-set   will  
not

 
be   registered.
Engine oil level indicator
depending on your vehicle's engine,
when the ignition is switched on,
the engine oil level is indicated for
a few
seconds, after the service
information. Oil level
correct
Low oil level
Flashing of "OIL",
linked
  with   the  
service

  warning   lamp,  
accompanied

  by   an  
audible

  signal   and   a   message   in   the  
screen, indicates a low oil level which
could

  damage   the   engine.
If   the   low   oil   level   is   confirmed   by   a  
check

  using   the   dipstick,   it   is   essential  
that

  the   level   is   topped   up.
Oil level gauge
fault
Flashing of "OIL--"
indicates a
malfunction   of   the  
engine

  oil   level   indicator.   Contact  
a

  CITROËN   dealer   or   a   qualified  
workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been of
f for
more
  than   30   minutes.Dipstick
A
  =   maximum,   never   exceed  
this level as a surplus of oil
may

  damage   the   engine.
Contact a CITR o Ë n dealer
or   a   qualified   workshop  
without

  delay.
B  
=
 
minimum,
 
top
 
up
 
the
 
level
 
via

  the   oil   filler   cap,   using   the  
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
  and   controls.  
When the lighting reaches
the

  minimum  
(or
 
maximum)   setting,   release   the  
button then press it again to increase
(or

 
reduce)
 
the   brightness.
a

s soon as the lighting is of the
required
 
brightness,   release   the   button.
Zero reset
Your CITROËN dealer or a qualified workshop  carries   out   this   operation  
after

  each   service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-

 
switch
  on   the   ignition.
The
  display   begins   a   countdown.
When the display shows "=0", release
the
  button;   the   spanner   disappears.

60
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
If the sunshine sensor
does not function correctly,
the  lighting   comes   on  
accompanied

  by   the   service  
warning

  lamp,   an   audible  
signal

 
and   a   message   in   the   screen.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Guide-me-home lighting
Keeping the dipped beam headlamps on   temporarily   with   the   ignition   off,  
makes

  the   driver's   exit   easier   when   the  
light

  is   poor.
HEADLAMP BEAM
The beam setting must be adjusted to suit
  the   load   in   the   vehicle.
0 -
  No   load.
1 -
  Partial   load.
2 -
 
A
verage   load.
3 -
  Maximum   authorised   load.
Manual operation
-
 
With

 
the
 
ignition
 
off,
 
"flash"
 
the
 
headlamps

 
within
 
one
 
minute
 
after
 
switching

 
off
 
the
 
ignition.
The
 
guide-me-home
 
lighting
 
switches
 
of

f
 
automatically
 
after
 
a
 
set
 
time.
Automatic operation
Refer to chapter 10, "Screen
menu
 
map"
 
section. Initial setting is position 0.
a

ctivate the function via the
vehicle
 
configuration
 
menu. Programming
The
 
system
 
is
 
activated
 
or
 
deactivated
 
in

 
the
 
vehicle
 
configuration
 
menu.
The
 
system
 
is
 
activated
 
by
 
default.
Switching off
The
 
system
 
does
 
not
 
operate:
-

below a certain angle of rotation of
the steering wheel,
-

 
above

 
25
 
mph
 
(40
 
km/h),
-
 
when

 
reverse
 
gear
 
is
 
engaged.
Switching on
This
 
function
 
starts:
-

when the corresponding direction
indicator is switched on,
or
-

 
from

 
a
 
certain
 
angle
 
of
 
rotation
 
of
 
the

 
steering
 
wheel.
With
 
dipped
 
or
 
main
 
beam
 
headlamps,
 
this

 
function
 
makes
 
use
 
of
 
the
 
beam
 
from

 
a
 
front
 
foglamp
 
to
 
illuminate
 
the
 
inside of a bend, when the vehicle
speed

 
is
 
below
 
25
 
mph
 
(approximately
 
40

 
km/h)
 
(urban
 
driving,
 
winding
 
road,
 
intersections,

 
parking
 
manoeuvres...).
Cornering lighting
Travelling abroad
If using your vehicle in a country
that drives on the other side of the
road,
  the   headlamps   must   be   adjusted  
to

 
avoid   dazzling   on-coming   drivers.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
The
 
function
 
is
 
deactivated
 
temporarily
 
when

 
you
 
use
 
the
 
manual
 
lighting
 
control

 
stalk.
Steering mounted controls

123
Berlingo-2-VP_en_Chap05_Securite_ed01-2016
Operation
When your vehicle is too close to or
approaches the vehicle ahead too
quickly  the   system   automatically  
applies

  the   brakes   to   avoid   a   collision.
You are then alerted by the display of a
message.
The
  brake   lamps   on   your   vehicle   come  
on

  to   warn   other   road   users.
The collision can be avoided
automatically
  if   the   difference   in  
speed between your vehicle and the
vehicle

  ahead   does   not   exceed   9   mph  
(15 km/h).
Above

  this   threshold,   the   system   will  
do what is possible to avoid or reduce
the accident by lowering the speed of
impact.
The

  automatic   braking   may   bring  
the

  vehicle   to   a   complete   stop   if   the  
situation

  requires   it.
In this case, the vehicle is held
stationary
  temporarily   (for   about  
1.5 seconds)

  to   allow   the   driver   to   take  
back

  control   by   pressing   the   brake  
pedal. The

  triggering   of   the   system   may  cause the engine to stall, unless
the driver depresses the clutch
pedal
  quickly   enough   during   automatic  
braking.
During

  automatic   braking,   the  
driver can always obtain a higher
rate of deceleration than that
controlled

  by   the   system,   by   pressing  
firmly

  on   the   brake   pedal.
After
  an   impact,   the   system   is  
automatically

  put   out   of   service:   it  
no

  longer   operates.
You
  must   go   to   a   CITROËN   dealer   or   a  
qualified

  workshop   to   have   the   system  
made

  operational   again.
Operating limits
The system only detects vehicles that are  stationary   or   moving   in   the   same  
direction

  as   your   vehicle.
It
  does   not   detect   small   vehicles  
(bicycles,

  motorcycles),  
pedestrians

  or   animals,   nor   non-
reflective
  stationary   objects.
The
  system   is   not   triggered   or   is  
interrupted

  if   the   driver:
-

accelerates strongly
-


or turns the steering wheel
suddenly

  (avoiding   manoeuvre).
In
  difficult   weather   conditions   (very  
heavy

  rain,   snow,   fog,   hail...),  
braking

  distances   increase,   which  
can

  reduce   the   ability   of   the   system   to  
avoid

  a   collision.
The
  driver   must   therefore   remain  
particularly

  vigilant.
Never
  leave   accumulations   of  
snow

  or   any   object   projecting  
above the bonnet or in front of
the

  roof:   this   might   fall   into   the   field   of  
vision of the sensor and generate a
detection.
driving safely
SaFETY
5

153
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Maintenance with TOTAL
TOTAL & CITROËN
Partners in performance and
protecting the environment
Innovation in the search for
performance
For over 40 year, the T
o
T
a
L Research and
Development
  departments   have   developed
 for

  CITROËN,   lubricants   to   match   the   latest
 technical innovations on CITR

o Ë n vehicles,
both
  for   competition   and   for   everyday   motoring.
For you, this is an assurance that you will
obtain
  of   the   best   performance   from   your  
engine.
Optimum protection for your
engine
By having your CITR

o Ë n
vehicle serviced with T
o

T
a
L
lubricants, you are contributing
towards
  improving   the   life   and  
performance

  of   your   engine,  
while also protecting the
environment. prefers
CHECkS
7