2016 Citroen BERLINGO MULTISPACE engine

32
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
WARNING LAMPS
Warning lamp is indicatesSolution - action
STOP on, associated
with another
warning
lamp
  and  
accompanied

 
by

  a   message  
in

  the   screen.major
  faults   linked   with  
the

  "Brake   fluid   level",  
"Engine oil pressure and
temperature",

  "Coolant  
temperature",

  "Electronic  
brake

  force   distribution"   and  
"Power steering" warning
lamps.Y

ou must stop as soon as it is safe to do
so. Park and switch off the ignition. Have it
checked by a CITROËN dealer or a qualified
workshop.
Parking
brake / Brake
fluid level /
EBFD on.
that the parking brake is applied or
  has   not   been   released   fully.Releasing the parking brake switches off the warning  lamp.
on. low
 
brake
 
fluid
 
level. Top   up   using   a   fluid   recommended   by   CITROËN.
remaining on even though the level
is correct and
associated with the
ABS
 
warning
 
lamp.
a fault with the electronic
brake  force   distribution. You must stop as soon as it is safe to do so.
Park and switch off the ignition.
Have it checked by a CITROËN dealer or a
qualified workshop.
Engine oil
pressure and
temperature on while
driving.
low pressure or a high
temperature. Park
  and   switch   off   the   ignition   then   allow   to   cool.
Visually
  check   the   level.
Chapter
  7,   "Levels"   section.
remaining on, even though the
level
  is   correct.a major fault. Have   it   checked   by   a   CITROËN   dealer   or   a  qualified
  workshop.
Each time the vehicle is started: a series of warning lamps comes on applying a self-test check. They   go   off   almost   immediately.
Engine   running:   the   lamp   becomes   a   warning   if   it   remains   on   continuously   or   flashes.
This
  initial   warning   may   be   accompanied   by   an   audible   signal   and   a   message   in   the   screen.
Do
  not   ignore   these   warnings.

33
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
Warning lamp isindicatesSolution - action
Coolant
temperature
and level on with needle
in the red
zone.
an
  abnormal   increase   in  
temperature.Park

  and   switch   off   the   ignition   then   allow   to   cool.  
V

isually   check   the   level.
flashing. a
  drop   in   the   coolant   level.Chapter
  7,   "Levels"   section.
Contact
  a   CITROËN dealer   or   a   qualified  
workshop.
Service on

  temporarily. minor   faults   or   warnings.Consult
  the   alert   log   in   the   display   or   screen.
If
  your   vehicle   is   equipped   with   a   trip   computer   or  
a

  screen:   refer   to   the   "Steering   mounted   controls"  
section

  in   Chapter   4.
Contact
  a   CITROËN   dealer   or   a   qualified  
workshop.
remaining

  on. major   faults.
Seat belt not
fastened on then
flashing.
the
  driver   and/or   front  
passenger has not fastened
their

  seat   belt.Pull
  the   strap   then   insert   the   tongue   in   the   buckle.
accompanied
 
by an audible
signal then
remains

  on.the
  vehicle   is   moving   with  
the

  driver's   and/or   front  
passenger's seat belt not
fastened.Check

  that   the   seat   belt   is   fastened   by   pulling   the  
strap.
Chapter

  5,   "Seat   belts"   section.
ECO on.
The
  Stop   &   Start system  
has put the engine in
ST

OP
 
mode   following   a  
vehicle

  stop   (red   light,   traffic  
jam, etc...).As

  soon   as   you   want   to   move   off,   the   warning  
lamp

  goes   off   and   the   engine   restarts  
automatically

  in   START
 
mode.
flashes
  for   a  
few seconds,
then

  goes   off.STOP
 

mode   is   temporarily  
unavailable.
or
ST

ART
 
mode   has   been  
invoked

  automatically.Chapter
  3,   "Stop   &   Start"   section.
REadY To Go
3

34
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
Warning lamp is indicatesSolution - action
Front /
lateral
airbag flashing
  or  
remaining

  on.a
  failure   of   an   airbag.Have
  the   system   checked   by   a   CITROËN   dealer  
or

  a   qualified   workshop   without   delay.
Chapter
  5,   "Airbags"   section.
Front
passenger's
airbag
deactivated on. the intentional deactivation
of this airbag in the
presence of a rearward
facing
  child   seat.Chapter
  5,   "Airbags"   or   "child   safety"   section.
Low fuel
level on with gauge
needle in the
red
  zone.When
  it   first   comes   on,  
there

  remains   around  
8 litres

  of   fuel   in   the   tank.  
The distance you can drive
on this fuel depends on
your style of driving and the
engine

  type.You
  must   fill   up   with   fuel   to   avoid   running   out.
This
  warning   lamp   comes   on   each   time   you  
switch

  on   the   ignition   until   you   have   filled   up.
Capacity
  of   the   tank:   approximately   60   litres.
Never
  risk   driving   until   the   tank   is   empty,   this  
could

  damage   the   emissions   and   injection  
systems.
flashing. cutting of

f of the fuel supply
following
  a   serious   impact.Restore
  the   supply.
Chapter
  7,   "Fuel"   section.
EOBD
emission
control
system flashing
  or  
remaining

  on.a
  failure   of   the   system.There
  is   a   risk   of   damage   to   the   catalytic  
converter

.   Have   it   checked   by   a   CITROËN  
dealer

  or   a   qualified   workshop.
Battery
charge on.
a fault in the charging
circuit. Check
  the   battery   terminals,   …
Chapter
  8,   "Battery"   section.
flashing. placing of the active
functions on standby
(economy
  mode).Chapter
  8,   "Battery"   section.
remaining
  on,  
in spite of the
checks.an

  ignition   or   injection  
malfunction.Have

  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.

+ +
39
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
SCR emissions control system
Alerts InformationSolution - action
The   UREA,   Service   and   diagnostic   warning   lamps  
come

  on,   an   SCR   emissions   control   system   fault  
has

  been   detected. This
  is   is   temporary   fault,   the   alert   disappears   as  
soon

  as   the   exhaust   emissions   return   to   normal  
levels.
After 30 miles (50 km) without

AdBlue
®
Confirmation of the fault which is not related to a lack  of   fluid. The
  remaining   driving   range   700   miles  
(1   100   km).
Go   to   a   CITROËN   dealer   or   a   qualified   workshop  
as

  soon   as   possible   to   avoid   a   breakdown.
The
  fault   is   confirmed.
The
  next   time   the   ignition   is   switched   on,   the  
authorised

  driving   range   will   be   displayed   in   miles  
(kilometres)

  and   the   alert   will   be   repeated   every  
30
  seconds.
The
  limit   of   the   driving   range   has   been   reached,  
exhaust

  emissions   levels   are   above   the   limits.
Starting
  is   impossible. To restart the engine, you must contact a
CITROËN
  dealer   or   a   qualified   workshop.
- BlueHDi Diesel
READY TO GO
3

40
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
FUEL GAUGEC OOLANT TEMPERATURE
The needle is positioned before the
red zone:
  normal   operation.
In arduous conditions of use or hot
climatic
  conditions,   the   needle   may  
move

  close   to   the   red   graduations.What you should do if the needle
enters the red zone:
Reduce your speed or let the engine
run
  at   idle.
What you should do if the warning
lamp comes on:
-  
stop
  immediately,   switch   off   the  
ignition.

 
The
  fan   may   continue   to  
operate

  for   a   certain   time,   up   to  
approximately

  10   minutes,
-
wait for the engine to cool down in
order

  to   check   the   coolant   level   and  
top

  it   up   if   necessary.
As   the   cooling   system   is   pressurised,  
follow the procedure below to avoid the
risk

  of   scalding:
-
wait at least one hour after
switching of

f the engine before
carrying   out   any   work,
-  
unscrew
  the   cap   by   1/4   turn   to  
allow the pressure to drop,
-

when the pressure has dropped,
check

  the   level   in   the   header   tank,
-  if   necessary,   remove   the   cap   to  
top up.
If

  the   needle   remains   in   the   red  
zone,

  have   the   system   checked   by  
a

  CITROËN   dealer   or   a   qualified  
workshop.Refer

  to   chapter   7,   "Levels"  
section.
Refer

 
to
 
chapter
 
7,
 
"Fuel"
 
section.
The
 
fuel
 
level
 
is
 
tested
 
each
 
time
 
the
 
key

 
is
 
turned
 
to
 
the
 
"running"
 
position.
The
 
gauge
 
is
 
positioned
 
on:
-

1:

 
the
 
fuel
 
tank
 
is
 
full,
 
approximately

 
60
 
litres.
-

0:

the reserve is now being used,
the
 
warning
 
lamp
 
comes
 
on
 
continuously

.
 
The

 
reserve
 
when
 
the

 
warning
 
first
 
comes
 
on
 
is
 
approximately

 
8
 
litres.

47
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
SERVICE INDICATOR
This programmes service intervals according  to   the   use   of   the   vehicle.More than 1 000 miles/km before the
next service is due
Example:
  4   800   miles/km   remain  
before

  the   next   service   is   due.   When  
the ignition is switched on and for a
few

  seconds,   the   screen   shows:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance

  recorder   resumes   normal  
operation showing the total and trip
distances.
Less than 1 000 miles/km before the
next service is due
Each time the ignition is switched on and for a few seconds,  the   spanner   flashes   and   the   number   of miles/kilometres

  remaining   is   displayed:
a few seconds after the ignition is
switched on, the oil level is displayed
(depending on version), then the total
distance
  recorder   resumes   normal  
operation

  and   the   spanner   remains   on.  
This indicates that a service should be
carried

  out   shortly.
Service overdue
Operation
A
 

few
 
moments
 
after
 
the
 
ignition
 
has been switched on, the spanner
indicating

 
a
 
service
 
operation
 
comes
 
on; the display for the total distance
recorder

 
gives
 
(in
 
round
 
figures)
 
the
 
distance

 
remaining
 
before
 
the
 
next
 
service.
The points at which a service is due
are

 
calculated
 
from
 
the
 
last
 
indicator
 
zero

 
reset.
The point at which a service is due is
determined
 
by
 
two
 
parameters:
-

the distance travelled,
-

 
the

 
time
 
which
 
has
 
elapsed
 
since
 
the

 
last
 
service.
The
 
distance
 
remaining
 
before
 
the
 
next

 
service
 
may
 
be
 
weighted
 
by
 
the

 
time
 
factor,
 
depending
 
on
 
the
 
type

 
of
 
driving. With the engine running the spanner
remains
  on   until   the   service   has   been  
carried

  out.
For BlueH
d i d iesel versions, this
alert
  is   also   accompanied   by   the   fixed  
illu

mination   of   the   Service   warning  
lamp,

  on   switching   on   the   ignition.
Each
  time   the   ignition   is  
switched on and for a few
seconds, the spanner
flashes

  and   the   excess  
distance

  is   displayed.
For BlueH
d i d iesel versions, the
spanner
  can   also   come   on   early,  
according the level of deterioration
of

  the   engine   oil.   Deterioration   of   the  
engine oil depends on the conditions of
use

  of   the   vehicle.
REadY To Go
3

48
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
Instruments and controls
Trip recorder zero
reset button
after this operation, if you wish to
disconnect   the   battery,   lock   the  
vehicle

  and   wait   for   at   least   five  
minutes,

  otherwise   the   zero   re-set   will  
not

 
be   registered.
Engine oil level indicator
depending on your vehicle's engine,
when the ignition is switched on,
the engine oil level is indicated for
a few
seconds, after the service
information. Oil level
correct
Low oil level
Flashing of "OIL",
linked
  with   the  
service

  warning   lamp,  
accompanied

  by   an  
audible

  signal   and   a   message   in   the  
screen, indicates a low oil level which
could

  damage   the   engine.
If   the   low   oil   level   is   confirmed   by   a  
check

  using   the   dipstick,   it   is   essential  
that

  the   level   is   topped   up.
Oil level gauge
fault
Flashing of "OIL--"
indicates a
malfunction   of   the  
engine

  oil   level   indicator.   Contact  
a

  CITROËN   dealer   or   a   qualified  
workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been of
f for
more
  than   30   minutes.Dipstick
A
  =   maximum,   never   exceed  
this level as a surplus of oil
may

  damage   the   engine.
Contact a CITR o Ë n dealer
or   a   qualified   workshop  
without

  delay.
B  
=
 
minimum,
 
top
 
up
 
the
 
level
 
via

  the   oil   filler   cap,   using   the  
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
  and   controls.  
When the lighting reaches
the

  minimum  
(or
 
maximum)   setting,   release   the  
button then press it again to increase
(or

 
reduce)
 
the   brightness.
a

s soon as the lighting is of the
required
 
brightness,   release   the   button.
Zero reset
Your CITROËN dealer or a qualified workshop  carries   out   this   operation  
after

  each   service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-

 
switch
  on   the   ignition.
The
  display   begins   a   countdown.
When the display shows "=0", release
the
  button;   the   spanner   disappears.

51
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2016
6-SPEED ELECTRONIC GEARBOx
- automatic  mode:   gear   selector   in  position
A.
-
 
manual
  mode:   gear   selector   in  
position

M.
For
  safety:
It
  is   only   possible   to   come   out  
of position

N   if   the   brake   pedal   is  
pressed.
The

  change   from   position   A (driving in
automatic
  mode)   to   position   M (driving
in
  manual   mode)   or   vice   versa   can   be  
made

  at   any   time.  
The
  warning   lamp   A
goes
  off   in   the   instrument   panel.
Mode selection Moving off
- To start the engine, the gear
selector   must   be   in   position   N.
-
 
Press
  firmly   on   the   brake   pedal.
-
 
Operate
  the   starter.
-

When the engine is running, place
the gear selector on

R, A or M as
desired.
-
 
Release
  the   brake   pedal   and  
accelerate.
If the gear selector is not in position

N,
and/or
  if   the   brake   pedal   is   not  
pressed,

  the   engine   will   not   start.  
Repeat

  the   above   procedure.
Reverse gear Engaging reverse gear
Move the gear selector to R.
Only attempt to select reverse gear
when the vehicle is stationary.
Neutral Changing to neutral
Move the gear selector to N.
  If   the  
vehicle

  is   moving,   do   not   select   this  
position

  even   momentarily.
REadY To Go
3
Gearbox and steering wheel