2016 AUDI TT COUPE warning light

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
.....
"' .....
-For security reasons, the windows can only
be
opened and closed with the remote con­
trol key at a maximum distance of approxi­
mately 6 ft (2 m) away from the vehicle.
When pressing the[@ button, always watch
the windows while they are closing so that
no one is pinched in the window. The closing
process will
stop immediately when the~
button is released.
Correcting power window malfunctions
After disconnecting the vehicle battery, the one­
touch up
and down feature must be activated
again.
~ Pull the power window switch until the window
is completely ra ised.
~Release the switch and pull it again for at least
one second.
Garage door opener
(Homelink)
Description
Applies to: vehicles with garage door opener (Homelink}
Fig.
27 Garage door opener: examp les of usage for diffe r­
ent system s
W ith the garage door opener (Homelink), you
can activate
systems such as the garage doors,
security
systems or house lights from inside your
vehicle. Up to three remote control functions can
be
programmed to the three buttons that are in­
tegrated in the control unit above the rearview
mirror .
T o
be able to operate systems using the garage
door opener, the buttons in the control unit must
first be programmed .
Opening and closing
A WARNING
f=
When operating or programming the garage
door opener, make sure that no people or ob­
jects are in the area immediately surrounding
the system. People can be inju red o r property
can be damaged if struck when closing.
@ Tips
-For security reasons, we recommend that
you clear the programmed buttons before
selling the vehicle.
- For
further information regarding Home­
Link,
refer to www.homelink.com .
-For the Declaration of Conformity with the
prov is ions from the FCC in the United States
and Industry Canada, refer to~ page 297.
Operation
Applies to: vehicles with garage door opener (Home link)
Fig .
28 Contro l panel above the interio r rearv iew mirro r
Requirement: the button in the control panel
must be programmed~ page 34 and the vehi­
cle
must be located within range of the system,
suc h
as the garage door.
~ Press the button to open the garage door. The
green LED@ blinks or turns on.
~ Press the button again to close the garage
door.
(j) Tips
To open or close the garage door, do not
press the button longer than 20 seconds or
the garage door opener will switch to pro­
gramming mode.
33

Downloaded from www.Manualslib.com manuals search engine Lights and Vision
Lights and Vision
Exterior Lighting
Switching lights on and off
Fig. 30 Instrument panel: light switch
Light switch ·'t/;
Turn the switch to the corresponding position.
When
the lights are switched on, the :oo: symbol
turns on.
0 -lights are off (in some markets, the daytime
running
lights* are switched on when the ignition
is switched on.)
-USA models: the daytime running lights sw itch
on automatica
lly when the ignition is sw itched
on and
the light switch is set to the 0 or the
AUTO position (only in daylight). The Daytime
running lights
can be switched on and off in
the MMI ~page 37 Q &.
-Canada models: the daytime running lights
switch on automatically when the ignition is
switched on and the light switch is set to the 0,
:oo: or the AUTO position (only in daylight) QA .
AUTO* -automatic headlights switch on and off
depending on brightness, for example in twilight,
during rain
or in tunnels.
:oo: -Parking light
~D -Low beam headlight
~ -All weather lights*
All-weather lights*
In vehicles with all-weather lights, the front
lights are adjusted automatically so that you are
less likely
to see glare from your own headlights,
for example when driving on a wet road.
36
Automatic dynamic headlight range control
system*
Your vehicle is equipped with a headlight range
control system
so that the headlights do not
blind oncoming traffic if the vehicle load
changes. The headlight range also
adjusts auto­
matically when braking and accelerating .
Light functions
The following light functions are available de­
pending on vehicle equipment and only function
when the
light switch is in the AUTO position.
You can deactivate these functions in the Info­
tainment system under Audi adaptive light
Qpage 37.
Static cornering light* (vehicles with LED head­
lights) -the cornering light switches on automat­
ically when the steeri ng wheel is turned at acer­
tain angle at speeds up to approximately 44 mph
(70 km/h) and when the turn signal is activated
at speeds up to approxim ately 25 mph (40 km/
h). The area
to the side of the vehicle is illuminat­
ed better when turning.
Highway light function* (vehicles with LED head­
lights) -this function adapts the lighting for
highwa y driving based on vehicle speed.
Speed dependent light distribution* (vehicles
with LED headlights) -the speed dependent light
distribution adapts the light in towns and on
highways
or expressways. Intersections can also
be illuminated on vehicles
with a navigation sys­
tem*.
A WARNING
- Automatic headlights * are only intended to
assist the driver. They do not reliev e the
driver
of responsibility to check the head­
lights and to turn them on manually accord­
ing to the current ligh t and visibility condi­
tions. For example, fog cannot be detected
by
the light sensors . So always switch on the
low beam under these weather conditions
and when
driving in the dark ~D.
-If the battery is dra ining significantly, the
parking lights will switch off automatically
to reduce the risk of the engine not starting . ..,..

Downloaded from www.Manualslib.com manuals search engine Always make sure your vehicle is parked and
adequately lit according to the laws. Avoid
using
the parking lights for several hours.
Switch
on the right or left parking light if
possible.
-
Please observe legal regulations when using
the lighting systems described.
Tips
-The light sensor for the automatic head­
lights*
is in the rearview mirror mount.
Therefore, do not place any stickers in this
area on the w indshield.
-
Some functions of the exterior lighting can
be
adjusted ~page 3 7.
-
If yo u turn off the ign ition whil e the exterior
lights are on and open the door, you will
hear a warning tone.
- In some markets, the tail lights will switch
on when the daytime running lights switch
on.
- In cool
or damp weather, the inside of the
headlights, turn signals and tail lights can
fog over due to the temperature difference
between the inside and outside. They will
clear shortly after switching them on. This
does not affect the service life of the light­
ing.
Turn signal and high beam lever
The lever operates the turn signals, the high
beoms
and the headlight flasher.
@
,
I
@
Fig. 31 Turn signal and high beam lever
"' 0 0
a'.: CXl
Lights and Vision
Turn signals¢ Q
The turn signals activate when you move the lev­
er into a turn signal position when the ignition is
switched on.
@-right turn signal
@
-left turn signal
The turn signal blinks three times if you tap the
lever (convenience turn signal).
High beams and headlight flasher §D
Move the lever to the corresponding position:
®-high beams on
@-high beams off or headlight flasher
The . indicator light in the instrument cluster
turns on.
A WARNING
High beams can cause glare for other drivers,
which increases
the risk of an accident. For
this reason, only use the high beams or the
headlight flasher when they will not create
glare for other drivers.
Adjusting the exterior lighting
The functions are adjusted in the Infotainment
system .
... Select in the Infotainment system: IMENUI but­
ton> Vehicle > left control button >V ehicle set­
tings > Exterior lighting.
Automatic headlights
You can adjust the following settings in the Au­
tomatic headlights
menu:
Activation time -you can adjust ifthe headlights
switch on Early, Medium or Late according to the
sensitivity of the light sensor.
Audi adapti ve light* -you can switch adaptive
light On and Off.
Daytime running lights*
USA models : the daytime running lights can be
switched on or off using the MMI. Select On or
Off. ....
37

Downloaded from www.Manualslib.com manuals search engine ..... N
G'. co ..... ID VI ..... ID .....
Instrument illumination
Fig. 34 Instrument illumination
The brightness of the instrument cluster and the
center console can be adjusted.
• Press th e knob to release it.
•Turn the knob toward"-" or"+" to reduce or in­
crease
the brightness.
•Press the knob again to return it to its original
position.
Vision
Adjusting the exterior mirrors
Fig. 35 Driver's door: knob for the exterior mirrors
Turn the knob to the desired posit ion:
Q/P -adjusting the left/right exterior mirror.
Move
the knob in the desired direction .
4iil -Heating the mirror glass depending on the
outside temperature .
8 -Folding exterior mirrors*. In the Infotain­
ment system, you can select if the mirrors fold in
automatically when you lock
the vehicle
~page29.
Lights and Vision
Front passenger's exterior mirror tilt
function*
To help you see the curb when backing into a
parking space,
the surface of the mirror tilts
slightly. For this to happen, the knob must be in
the position for the front passenger 's outside
mirror.
You can adjust the tilted mirror surface by turn­
ing the knob in the desired direction . When you
move
out of reverse and into another gear, the
new
mirror position is stored and assigned to the
key you are using.
The
mirror goes back into its original position
once you drive forward faster than 9
mph
(15 km/h) or turn the ignition off.
A WARNING
Curved mirror surfaces (convex) enlarge the
field of vision. However, they make objects in
the mirror appear smaller and further away.
Your may estimate incorrectly when you use
these mirrors
to gauge your distance from the
vehicles behind you when changing lanes -ac­
cident risk!
CJ) Note
If the mirror housing was moved by outside
f orces (such
as an impact when maneuver­
ing), you
must use the power folding function
to fold the mirror all the way out. The mirror
housing must not be moved back into place
by hand because
this would impair the func­
tion of the mirror mechanism.
@ Tips
If the power adjusting function malfunctions,
the glass in both mirrors can be adjusted by
pressing on
the edge of it by hand.
39

Downloaded from www.Manualslib.com manuals search engine Lights and Vision
Dimming the mirrors
Fig. 36 Automatic dimming rearview mirror•
Manual dimming rearview mirror
,...
-0
~ ID
... Pull the lever on the bottom of the mirror back.
Automatic
dimming rearview mirror*
... Press t h e button@ C) fig . 36. The ind icator
light @turns on. Interior and exterior mir rors*
will dim wh
en there is in com ing light (such as
headlights from the rear) .
A WARNING
Electro l
yte fluid can leak from automatic dim­
m ing mirrors ifthe glass is broken . Electro­
lyte fluid can
irritate skin, eyes and airways.
-
Repeated or long-term exposure to electr o-
lyte fluid can lead
to irritation of the air ­
ways, especially in people with asthma or
oth e r respiratory co ndi tions. T ak e deep
breaths immediately after leaving the vehi­
cle or, if this is not possible, open all of th e
doors
and win dows as wide as possible .
-If electrolyte f luid enters the eyes, flush
t h
em thoroughly with a la rge amount of
clean wa ter for at least 1 5 mi nutes and t hen
seek medical attention.
- If e lectrolyte fluid comes into conta ct w ith
th e skin , flush the affected a rea with clean
water for at least 15 minutes and then clean
with
soap and water and seek medica l at­
tention. Clean affected clothing and shoes
thoroughly befo re wearing again .
-
If the fluid was swallowe d and the person is
conscious, flush the mouth with water for at
least 15 m inutes. Do not induce vomiting
unless this is recommended by medical pro-
40
fessiona ls . Seek medical attention immedi­
ately.
CD Note
I f t he
glass on an a utomatic dimming mirro r
b reaks,
electrolyte can leak out. T his liquid
damages plastic surfaces. Remove th e liquid
as quickly as possible, for example us ing a
wet sponge.
(!}Tips
-If the light reaching the rearview mirror is
obstructed, the automatic dimming mirror
w ill not function correctly,
- The
automatic dimming m irrors do not dim
when the interio r lighting is turned on or
th e reverse gear is selected .
Sun visors
Fig. 37 S un sh ade
The sun visors can be moved out of their brackets
and turned toward the doors C>fig. 37@ . The
mirror light switches on when the cover over the
vanity mirror@ opens .

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
.....
"' .....
Windshield wipers
Switching the windshield wipers on
Fig. 38 Windshield wiper lever
Move the windshield wiper lever to the corre­
sponding position:
@ -windshield wipers
off
@-interval mode. To increase/decrease the wip­
er intervals , move
the switch @ to the left/right.
In vehicles with a rain sensor*, the wipers turn on
in the rain once the vehicle speed exceeds ap­
proximately 2 mph (4
km/h). The higher the sen­
sitivity
of the rain sensor* is set (switch @ to the
right),
the earlier the windsh ield wipers react to
moisture on the windsh ield. You can deact ivate
the rain sensor mode* in the Infotainment sys­
tem, which switches the intermittent mode on.
Select
in the Infotainment system: I MENU! bu t­
ton> Vehicle > left control button >Driver assis­
tance > Rain sensor > Off.
@-slow wiping
@ -fast wip ing
©
-singl e w ipe If you hold the lever in this posi ­
tion longer, the wipers switch from slow wiping
to fast wiping .
® -clean
the windshield To eliminate water
droplets, the windshield wiper performs one af­
terwipe
after several seconds in temperatures
above
39 °F (4 °C). You can switch this function
off by moving the lever to position ® within 10
seconds after the afterwipe . The afterwipe func­
tion is reactivated the next time you switch the
ignition on.
Cleaning the headlights* . The headlight washer
system*
only functions when the lights are
Lights and Vision
switched on. The headlights are automatically
cl eaned
the first time and every fifth time the
lever is moved to position ® ·
A WARNING
f-==" -I
- The rain sensor* is only intended to assist
the driver. The driver is still responsib le for
manually switching the wipers on according
to the visibility conditions .
- The windsh ield may
not be treated with wa­
ter-repelling windshield coating agents. Un­
favorable conditions, such as wetness, dark­
ness, and when
the sun is low, can cause in­
creased glare which increases
the risk of an
accident.
Wiper blade chatter is also possi­
b l
e.
-Properly functioning windshield wiper
b lad
es are required for a clear view and safe
driving
<:::>page 42, Replacing windshield
wiper blades.
CD Note
-In the case of frost, check whether the
windshield wiper blades are frozen to the
windshield. Switching on the windshield
wipers
can damage the w ip er blades!
-
Prior to using a car wash, the windshield
w ip er system
must be switched off (lever in
position
0). This prevents unintentiona l
switching on and damage
to the windsh ield
wiper system .
@Tips
-The windshie ld wipers switch off when the
ignition is turned off. Activate the wind­
shield wipers
after the ignition is switched
back on by moving
the windshield wiper lev­
er
to any position.
-
Worn or dirty windshie ld wiper blades result
in streaking.
This can affect the rain sensor*
function .
Check your windshield wiper
blades regularly .
- The washer fluid nozzles in
the windshield
washer system are heated*
at low tempera­
tures when
the ignition is on.
- When stopping
temporarily, such as at a
traffic light, the speed of the windshield
w ipers automatically reduces by one level.
41

Downloaded from www.Manualslib.com manuals search engine Lights and Vision
Cleaning windshield wiper blades
Clean the wiper blades when you see wiper
streaks.
Clean the wiper blades with a soft towel
and glass cleaner.
"" Place the windshield wiper arms in the service
position
~page 42.
"" Fold the windshield wiper arms away from the
windshield.
& WARNING
Dirty windshield wiper blades can impair vi­
sion, which increases
the risk of an accident.
Replacing windshield wiper blades
Fig. 39 Removing windshield wiper blades
Wiper service pos ition /blade repl acement
positi on
-
"' ~ 0 ci:
"' QJ
.,.. To bring the wipers into the service position,
turn the ignition off and move the windshield
wiper lever
into position@~ page 41, fig. 38.
.,.. To bring the wipers into the starting position,
turn the ignition on and move the windshield
wiper lever
into position@) for at least two sec­
onds
q page 41, fig. 38.
Removing the wiper blade
.,.. Fold the windshield wiper arm away from the
windshield.
"" Press the locking knob@~ fig. 39 on the wiper
blade. Hold
the wiper blade firmly .
.,.. Remove the wiper blade in the direction of the
arrow.
42
Installing the wiper blade
.,.. Insert the new wiper blade into the mount on
the wiper arm @until you hear it latch into
place.
.,.. Place the wiper arm back on the windshield.
.,.. Turn the service position off.
& WARNING
For safety reasons, the windshield wiper
blades should be replaced once or twice each
year.
CD Note
- The windshie ld wiper blades must only be
folded away when in the service position!
Otherwise, you risk damaging the paint on
the hood or the windshield wiper motor.
-
You should not drive your vehicle or press
the windshield wiper lever when the wiper
arms are folded away
from the windshield.
The windshield wipers would move back in­
to their original position and could damage
the hood and windshield.
(j) Tips
-You can also use the service position, for ex­
ample,
if you want to protect the windshield
from icing by using a cover.
-
You cannot activate the service position
when
the hood is open.
Digital compass
Switching the compass on and off
Applies to: vehicles with digital compass
0 N
!
Fig. 40 Rearview mirror: digital compass is sw itched on

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
.....
"' .....
"'To turn the compass on or off, press the button
@ until the compass in the mirror appears or
disappears.
The digital
compass only works when the ignition
is turned on. The directions are indicated with ab­
breviations :
N (north), NE (northeast), E (east),
SE (southeast), S (south), SW (southwest), W
(west), NW (northwest).
@ Tips
To prevent inaccurate compass readings, do
not bring any remote controls, electrical devi­
ces
or metallic objects near th e mirror .
Adjusting the magnetic zone
Applies to: veh icles with digita l compass
®
Fig. 41 Nort h Amer ica: magnetic zone map
"' Press and hold the button@¢ page 42, fig. 40
until the number of the magnetic field zone ap­
pears in the rearview mirror.
"' Press the button@repeatedly to select the
correc t magnetic zone. The selection mode
turns off after a few seconds .
Lights and V ision
Calibrating the compass
Applies to: vehicles with digita l compass
If the display is i ncorrect or inaccurate, the com­
pass must be reca librat ed.
"' Press and hold the button@until a C appears
in the rearview mirror .
"' Drive in a circle at about 5 mph (10 km/h) until
a direction
is displayed in the rearv iew mirror.
WARNING
- To avoid endangering yourself and other
drivers, calibrate the compass in an area
where there is no traffic.
- A lways pay
attention to the traffic and the
area around your vehicle if you are reading
the compass while driving .
43