2016 AUDI S3 service

Warm and cold
outlet, regardless of whether it is protected
against a short circuit or not.
- Always disconnect the connector cable and
close the cover
(D before starting the engine.
.&_ WARNING
Using the engine preheater incorrectly can
cause short circuits, electric shocks, fire, seri­
ous injuries and death.
- The connector cable must always be con­
nected to a grounded 120 Volt socket that
is equipped with a GFI circuit breaker . Al­
ways protect the sockets from water, mois ­
ture and other fluids .
- Never plug the engine preheater into a con­
ventional outlet, regardless of whether it is protected against a short circuit or not .
.&_ WARNING
-
Short circuiting, fire, serious injuries and life­
threatening or lethal electric shock can result
from using unsuitable or damaged sockets and connector cables/extension cords, using
electrical equipment incorrectly, and/or disre­
garding general safety precautions.
- Always plug the extension cord into a 120 V
socket that is properly functioning, ground­
ed, equipped with a GFI circuit breaker and
is protected against water, moisture and
other fluids.
- Never connect the engine preheater to a
conventional socket, even if the socket is
protected by a fuse.
- Always check the fuse on the 120 Volt GFI
socket before connecting the connector ca­
ble to the engine preheater on the vehicle.
- Only use highly durable extension cords that
are class 12 or better and can be properly grounded to a three-prong wall socket with
a GFI circuit breaker . The extension cord
must not be longer than 100 feet (30 me­
ters).
- Never use damaged connector cables, ex­
tension cords or sockets . Always check the
connector cable, extension cord and sockets
for damage before using them. Damaged
parts must be replaced. If damaged, replace
76
the engine preheater connector cable at an
authorized Audi dealer or authorized Audi
service facility .
- Only use the connector cable provided to
connect the vehicle socket to a suitable
power source. Use a suitable extension cord
if necessary .
- Always disconnect the connector cable from
the vehicle socket before starting the en­
gine. Switch off the power supply to the
connector cable and to the extension cord if necessary, or disconnect the cable or exten­
sion cord from the 120 Volt socket equip­
ped with a GFI circuit breaker. Never leave
the connector cable or extension cord con­
nected to a live power source.
- Never make alterations or repairs to the
connector cables or extension cords that
supply power to the engine preheater or to
any components that affect the engine pre­
heater.
- Always protect the connections from water,
moisture and other fluids. Always store the
connector cable and extension cord securely
and in a dry place when they are not being
used, and disconnect them from the power
source before storing .
(D Tips
Test the GFI circuit breaker once a month if
you use the engine preheater occasionally, and test it weekly if you use it regularly.

Driving
If you anticipate what you need to do next and
drive economically, you can easily cut your fuel
consumption by 10-15 percent. This section will
give you some tips on how you can help the envi­ ronment and your pocketbook.
(D Tips
The consumption estimates as published by ENVIRONMENTAL PROTECTION AGENCY
(EPA) and Transport Canada may not corre­
spond to your actual consumption on the
road, which will vary depending upon vehicle
load and speed, road and weather conditions,
trip length, etc.
Drive smoothly and keep a lookout ahead
Vehicles use the most fuel when they are acceler­
ating.
.. Avoid unnecessary accelerating and braking .
Vehicles use the most fuel when they are acceler­
ating. If you anticipate what is going to happen next, you will need to brake less and, thus, accel­
erate less. Let the vehicle coast whenever possi ­
ble -for example when you see that the next traf­
fic light is red.
Avoid full throttle
Driving at moderate speeds saves fuel and im­
proves your mileage.
.. Try and keep well below your car's maximum
speed .
Accelerating gently reduces fuel consumption,
engine wear, and does not disturb the environ­ ment.
Fuel consumption, exhaust emissions and engine
noise increase disproportionately at high speeds.
If you drive at approximately three quarters of
top speed, fuel consumption will be reduced by
one half . Never drive faster than the posted
speed limit and weather conditions permit.
78
· Reducing unnecessary idling
Even when your car is just idling it burns up fuel .
.. Shut the engine off when you are not driving
the vehicle .
.,. Do not warm up the vehicle by letting the en-
gine run at idle .
It is efficient to switch off the engine when stop­
ped at railroad crossings and long red lights.
Turning the engine off for just 30 -40 seconds
saves more fuel than is burned by starting the
engine again .
It takes a long time for the engine to warm up
fully when it is running at idle . However, wear
and noxious emissions are especially high when
the engine is warming up . So you should drive
away as soon as you start the engine and avoid running at high rpms while the engine is still
warming up .
@ Note
Do not leave engine idling unattended after
starting. If warning lights should come on to
indicate improper operation, they would go
unheeded. Extended idling also produces
heat, which could result in overheating or
other damage to the vehicle or other proper­
ty.
Regular maintenance
A badly tuned engine unnecessarily wastes a lot
of fuel.
.. Have your vehicle serviced at regular intervals.
By having your vehicle regularly serviced by an
Audi dealer helps to ensure that it runs properly
and economically. The condition of your vehicle
not only affects its safety and ability to hold its
value, it also affects
fuel consumption.
Check your oil each time you fill your tank.
The amount of oil used is related to engine load
and speed.
It is normal for the oil consumption of a new en­
gine to reach its lowest value after a certain mile -
age has been driven . ..,.

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
You must drive your vehicle about 3,000 miles
(5 ,000 kilomet ers) before you can prop erly as ­
sess o il consumption .
This a lso applies to fuel consump tion and engine
output .
(D Note
-Have your vehicle mainta ined properly and
i n accor dance wi th the service re commenda­
tions in yo ur War ranty
& Maintenance book ­
l et. Lack of proper maintenance as well as
i mproper use of the vehicle will impair the
function of the emission control system and
could lead to damage .
- Do not alter or remove any component of
the Em ission Control System unless ap­
proved by the manufacturer.
- Do not alter or remove any device, such as
heat shie lds, sw itches, ignition wires,
valves, which a re designed to protect yo ur
vehicle's Em ission Control System and other
i mportant vehicle components.
Fewer short trips
Fuel consumption will always be relatively high
on short trips.
• Try to avoid driving short dist ances with a cold
engi ne .
T he eng ine and catalytic converter have to reach
their optimal
operating tempe rature to reduce
fuel consump tion and noxious emissions effec­
tively .
Just after starting, a cold engine in a mid-si ze car
only achieves a fuel economy of 6-8 miles per
ga llon (30-40 l/100 km). A fter about a half a
m ile , fuel economy cl imbs to 12 mpg (20 l/
100 km) . After about
2.5 miles (4 km), the en­
g ine is a t its prope r operating temperature and
fuel economy has reache d a normal level. So you
c a n see t hat you s hou ld avoid sho rt t rips whenev­
er possib le .
The
outside temperature is also cr itical in th is re­
g ar d. Yo ur car c onsumes mo re fuel in the w in ter
than in the s umme r.
D rivi ng
Steering
Adjusting the steering wheel position
The steering wheel position is fully adjustable up
and down and forward and back.
F ig . 7 6 Stee rin g c olu m n: steering co lumn adjustm en t leve r
• Tilt the leve r¢ fig. 76 downward ¢&_ .
• Bring the steer ing whee l into the desired pos i­
tion.
• Push the lever against the steer ing column un­
til it latches.
A WARNING
-
Incorrect use of the stee ring wheel adjust­
ment and an incorrect seat ing position can
cause ser ious injuries .
- On ly ad just the steering column when the
veh icle is stationary so that yo u do not lose
con trol of the vehicle.
-
-Ad just the driver 's sea t or s teer ing whee l so
that the re is at least 10 inc hes (25 cm) dis­
tance be tween your ches t and t he steer ing
wheel
r:!> p age 16 7, fig. 1 48 . If y ou d o not
main tain t his d istance, t he ai rb ag sys tem
will not be ab le to provide its fu ll pro tection
r:!> page 167, fig . 148.
- If your phy sical ch aracteris tic s prevent you
from sitting at least 10 inches ( 25 cm) o r
mo re away from the steer ing whee l, see if
your author ized Audi dealer or authorized
Aud i Serv ice Facility can provide adapters
that will help.
- If your face is level with the steer ing whee l,
the airbag does not provide as much protec­
tion dur ing a col lision . Always make sure
that the steer ing whee l is level w ith your
chest.
~
79

Driving
-Always hold the steering wheel with your
hands in the 9 o'clock and 3 o'clock posi­
t ions to reduce the risk of injury if the airbag
deploys.
- Never hold the steer ing whee l in the
12
o'clock posit ion or with both hands on the
rim or the center of the steer ing whee l.
Holding the steering wheel inco rrectly s ig­
nificantly incr eas es the risk of inju ry to the
h ands, arms and head if t he ai rbag dep loys.
Starting and stopping
the engine (vehicles with
an ignition Lock)
Starting the engine with the key
A pp lies to veh icles: w ith ig ni tion lock
The ignition is switched on and the engine start­
ed with the key in the ignition .
Fig . 77 Ign it io n key pos it ions
Stee ring lock
If the steering whee l w ill not turn, the steering
lock is engaged .
.,. To release the steering wheel lo ck, inse rt the
k ey i n the ignition lock and tu rn t he key in the
-d irection of the arrow- while tu rning the steer­
ing wheel.
Sw itching the ignition on/off or preheating
.,. To switc h the ignition on, turn the ign ition key
to posit io n @ . The need le in the tachometer
moves into the
READY position.
.,. To switc h the ign ition off, turn the ignit ion key
to position @. The need le in the tachometer
moves into the
OFF position.
80
D iesel ve hicl es are p reheated while the ig nition is
switched on
m .
Starting the engine
You r vehicle is equipped wi th la unch control. As
soon as you have turned the ig nition key to pos i­
tion @, the eng ine will start au tomati cally .
.,. Press the brake pedal and move the sele ctor
lever to the P o r
N position.
.,. Turn the key briefly to pos it ion @. The ign ition
key a utomat ically returns to position @. D o not
press the acce lerator peda l when doing this.
Major elec trical equipmen t sw itches off tempora­
r ily whe n starting the engine.
It is possible t hat there will be a s ligh t de lay
whe n starting the engine in diesel veh icles in
colder temperatu res. Therefore, yo u must hold
t h e b rake pedal down until the eng ine starts . T he
i ndicato r ligh t turns on wh ile the engine is pre­
heating
iJ.
The preheating time depends on the coolant
temper ature and o utside temperature. The glow
pl ug indi cato r light
m will only tu rn on for ap­
proximately
1 second when the engine is warm or
t h e outside temperat ure is higher than
8 °C. That
means you can start the engine
immediately.
I f the engine does not s tart immedia tely, s top
the starti ng p rocedure by tu rni ng the ig nition key
to posit ion @ and repeat after
30 seconds .
Automatic start malfunction
There is an a utom atic st art ma lf u nct ion if the ~
(ga so lin e engine) or
m (diese l eng ine) indica tor
li ght tur ns on and the message
Engine start sys·
tem malfun ction! Please contact Service
ap ­
pears.
To star t the engine, hold the igni tion key in pos i­
tion @unt il the engine r uns.
D rive to an au thori zed A udi dealer or au thori zed
A udi Se rvice Fa cility immed iate ly to h ave the
malfunc tion correc ted .
& WARNING
- To red uce the r isk o f po ison ing, never allow
the engine to run in conf ined spaces .

,....,
N
0 > co ,...., Automatic start malfunction
There is an automatic start malfunction if the~
(gasoline engine) or
II (diesel engine) indicator
light turns on and the message
Engine start sys­
tem malfunction! Please contact Service
ap­
pears.
To start the engine, press and hold the
I S TART ENGINE STOPI button until the engine
runs.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
& WARNING
- To reduce the risk of poisoning, never allow
the engine to run in confined spaces.
- Always take the vehicle key with you when
leaving the vehicle, even for a short period
of time. This applies particularly when chil­
dren remain in the vehicle. Otherwise the
children could start the engine or operate
electrical equipment such as power win­
dows .
- Please note that the brake booster and pow­
er steering only work when the engine is
running . When the engine off, you must use
more force to steer or brake the vehicle. Be­
cause the usual steering and braking capa­
bility is not available, the risk of accidents or
injuries increases.
(D Note
- Avoid high engine speed, full throttle, and
heavy engine load as long as the engine has
not reached operating temperature yet. You
could damage the engine.
- The engine cannot be started by pushing or
towing.
@) For the sake of the environment
Do not let the engine run while parked to
warm up. Begin driving immediately. This re­
duces unnecessary emissions.
,....,
Driving
{!) Tips
-Some noise after starting the engine is nor­
mal and is no cause for concern.
- If the . indicator light blinks in the instru­
ment cluster before switching the ignition
off, the ignition will not switch on again.
¢page 162
-If you leave your vehicle with the ignition
switched on, the ignition will switch off af­
ter a certain amount of time. Make sure that electrical equipment such as the exterior
lights are switched off .
Turning the engine off using the
button
Applies to vehicles: with convenience key
Plug-in hybrid drive*: refer to the information un­
der
¢ page 100.
"' Bring the vehicle to a full stop.
"' Move the selector lever into the P position.
.. Press the
!STAR T ENGINE STOP ! button
¢ page 82, fig. 78.
The needle in the tachometer moves to OFF when
the ignition switches off.
Steering lock1
)
The steering locks when you turn the engine off
using the
I START ENGINE STOPI* button, move
the selector lever into the P position and open
the driver's door.
The locked steering helps prevent vehicle theft.
Emergency off function
If it is absolutely necessary, the engine can also
be turned off while driving at speeds lower than
6 mph (10 km/h). To switch the engine off, press
the
I START ENGINE STOPI button twice in a row
briefly or press and hold for longer than two sec -
onds. ..,.
83

Driving
_& WARNING
- Never turn off the engine before the vehicle
has come to a complete stop. The full func­
tion of the brake booster and the power
steering is not guaranteed. You must use
more force to turn or brake if. Because you
cannot steer and brake as you usually
would, this could lead to accidents and seri­
ous injuries.
- Please note that the brake booster and pow­
er steering only work when the engine is
running. When the engine off, you must use
more force to steer or brake the vehicle. Be­
cause the usual steering and brak.ing capa­
bility is not available, the risk of accidents or
injuries increases .
- Always take the vehicle key with you when
leaving the vehicle, even for a short period
of time. This applies particularly when chil­
dren remain in the vehicle . Otherwise the
children could start the engine or operate
electrical equipment such as power win­
dows.
- For safety reasons, always park the vehicle
with the selector lever in the P position.
Otherwise, there is the risk that the vehicle
could roll.
- After the engine has been switched off, the
radiator fan can continue to run for up to 10
minutes -even with the ignition switched
off. It can also switch on again after some
time if the coolant temperature rises as the result of heat buildup or if the engine com­
partment is heated by the sun's rays and the
engine is hot.
(D Note
If the engine has been under heavy load for
an extended period of time, heat builds up in
the engine compartment after the engine is
switched off- there is a risk of damaging the
engine. For this reason, let the engine run for
at idle for approximately two minutes before
shutting it off.
84
Starting the engine if there is a
malfunction
Applies to vehicles: with convenience key
It may not be possible to start the engine under
certain circumstances, for example if the battery
in the vehicle key is drained, if interference is af­
fected the key or if there is a system malfunc­
tion.
Fig. 79 Steering column/remote control key: starting the
e ngin e if there is a malfunct ion
As long as the message y>>) Key not recognized.
See owner's manual
appears, you can start your
vehicle using the emergency start function.
.,. Press the brake pedal¢ ,&.
in Engine with the
button
START ENGINE S TOP Starting on
page 83.
.,. Press the ~1s=T-A~R~T~E-N~G=r-N~E~S~T~O~P~ I button.
.,. Hold the master key in the location indicated as
shown in the illustration
t>>) ¢ fig. 79. The en­
gine will start.
.,. If the engine does not automatically start,
press the
I START ENGINE STOPI button again .
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected .
@ Tips
You can display the message that appears
during an emergency by pressing the
I START ENGINE STOPI* button.
Messages
Turn off ignition before leaving car. Battery is
discharging .,.

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
This message appears and a warning tone sounds if you open the driver's door when the ignition is
switched on. Switch the ign ition off so that the
battery will not d ischarge.
Pressing start/stop button again will switch off
engine!
This message appears when you press the
ISTART ENGINE STOPI* button while driving
¢ page 83, Emergency off function.
Engine start system malfunction. Please con­
tact Service
The engine automatic start system has a mal­
function . Drive to an author ized Audi dealer or
author ized Audi Service Facility immediate ly to
have the malf uncti on corrected. To start the en­
g ine, press and hold the
!START ENGINE STOPI
button.
DJ Key not recognized. See owner's manual
This message appears if there is no convenience
key inside the vehicle or if the system does not
recognize the key. The conven ience key may not
be recognized, for example, if it is covered by an
object that
disrupts the signal (such as a brief­
case), o r if the key battery is weak. Electronic de­
vices such as cell phones can also interfere with
the signal.
To still be able to start or stop the engine, refer
to "Cor rect ing a malfunction" ¢
page 84.
Ill Key not in vehicle?
The Ill indicator light turns on and this message
appears if the convenience key was removed from
the vehicle when the eng ine was running . If the
conven ience key is no longer in the vehicle, you
cannot switch the ignition on o r start the engine
once yo u stop it. In addition, you cannot lock the
ve hicl e from the outside .
Press brake pedal
This message appears if you do not press the
brake pedal when starting the eng ine .
Please engage N or P
This message appears when starting or s topping
the engine if the selector lever is not in the Nor P
position . The engine will not start/stop .
Driving
Shift to P, vehicle can roll away . Doors can only
be locked in P
T his message appears for safety reasons along
with a warning tone. It appears if the selec to r
lever for the automat ic transmission is not in the
P position when switching the ignition off with
the
I START ENGINE STOPI * button. Shift these­
lector lever to the P position. Otherwise, the vehi­
cle could roll. You also cannot lock the vehicle us­
ing the locking sensor o n the door hand le or us ­
ing the conven ience key.
Electromechanical
parking brake
Operating
The electromechanical parking brake replaces
the hand brake.
Fig . 80 Center console : pa rk ing brake
" Pull the switch @¢ fig. 80 to set the parking
brake. The - (USA models),. (Canada
models) ind icator lights in the button and in
the instrument cluster display turn on .
" To release the parking brake, press the brake or
accelerator pedal while the ign ition is switched
on and press the button @at the same time.
The - (USA models), . (Canada models)
ind icator lights in the button and in the display
turn off.
Your vehicle is equipped with an electromechani­
cal park ing brake. The parking brake is designed
to prevent the vehicle from rolling un intent io nal ­
ly and replaces the hand brake .
In addition to the normal functions of a tradi­
t ional hand brake, the electromec hanical parking ..,.
85

Driving
brake provides various convenience and safety
functions.
When starting from a stop
- The integral hill start assist helps you when
driving by automatically releasing the parking
brake
c:;, page 87, Starting from a stop.
- When starting on inclines, the hill start assist
prevents the vehicle from unintentionally roll­
ing back. The braking force of the parking brake
is not released until the wheels build up
enough driving force.
Emergency brake function
The emergency braking function ensures that the
vehicle can be slowed down even if the
standard
brakes fail c:;, page 87, Emergency braking
function.
A WARNING
- Do not press the accelerator pedal inadver­
tently when the vehicle is stationary and the engine is running and a gear is selected.
Otherwise the vehicle will start to move im­
mediately and could result in a crash.
- If the power supply fails, the released park­
ing brake can no longer engage. In this
case, park the vehicle on level ground and
secure it by placing the selector lever in the
P position . See an authorized Audi dealer or
authorized Audi Service Facility for assis­
tance.
(D Note
If the . or .. (USA models) /. (Canada
models) indicator light in the instrument
cluster blinks, there is a malfunction in the
brake system. Refer to the detailed descrip­
tion of the indicator lights
c:;, page 18.
-If the - (USA models) /. (Cana-
da models) or
Ill indicator light turns on,
there is a malfunction in the parking brake
c;, page 19.
@ Tips
-If the parking brake is set while the ignition
is switched off, the
¢~jj indicator light in the
button and in the instrument cluster dis-
86
play - (USA models) /. (Canada mod­
els) will turn off after a certain amount of
time.
- If driver's door is opened while the ignition
is switched on, the parking brake sets auto­
matically. This prevents unintended rolling
of the vehicle.
- Occasional noises when the parking brake is
set and released are normal and are not a
cause for concern.
- When the vehicle is parked, the parking
brake goes through a self-test cycle at regu­
lar intervals. Any noises associated with this
are normal.
- If there is a power failure, the parking brake
will not set if it is released, and it will not release if it is set
c:;, I!:::,. . See an authorized
Audi dealer or authorized Audi Service Fa­ cility for assistance.
· Parking
.,. Press the brake pedal to stop the vehicle.
.,. Pull the switch @
c:;, page 85, fig. 80 to set the
parking brake.
.,. Place the selector lever in the P position.
.,. Turn the engine off
c:;, & -
.,. Turn the steering wheel when parking on in­
clines so that the wheels will roll into the curb
if the vehicle starts moving.
A WARNING
- Always take the vehicle key with you when
leaving the vehicle, even for a short period
of time . This applies particularly when chil­
dren remain in the vehicle. Otherwise chil­
dren could start the engine, release the
parking brake or operate electrical equip­
ment such as power windows, which in­
creases the risk of an accident.
- When the vehicle is locked, no one -particu­
larly not children -should remain in the ve­
hicle. Locked doors make it more difficult
for emergency workers to get into the vehi­
cle, which puts lives at risk.