2016 AUDI Q3 brake wear

Seats and storage
_& WARNING
Never place any objects in the driver's foot­
well. An object could get into the pedal area and interfere with pedal function. In case of
sudden braking or an accident, you would not
be able to brake or accelerate.
Front passenger's seat
Always move the front passenger seat into the
rearmost position.
To avoid contact with the airbag while it is de­
ploying, do not sit any closer to the instrument
panel than necessary and always wear the three­
point safety belt provided adjusted correctly. We
recommend that you adjust the passenger's seat
i n th e following manner:
• Move the front passenger seat into the rear­
most position of the fore and aft adjustment
range ¢,&.
in Why is your seat adjustment so
important? on page 49.
• Bring the backrest up to an (almost) upright
position. Do not ride with the seat reclined.
• Adjust the head restraint so the upper edge is
as even as possible with the top of your head. If
that is not possible, try to adjust the head re­
straint so that it is as close to this position as
possible¢
page 51.
• Place your feet on the floor in front of the pas­
senger's seat.
Front seats
Manual seat adjustment
Applies to vehicles: with manually adjustable seats
Fig. 51 Front seats: manua l seat adjustme nt
50
(D -Moving the seat forward/back: pull the lever
and slide the seat.
@-Lengthen ing/shortening the upper thigh
support*: lift the handle.
@ -Adjusting the angle of the seat surface*.
Pull/press the lever.
@) -Adjusting the lumbar support*: press the
button in the desired direction.
® -Moving the seat up/down: pull/press the lev­
er.
@ -Adjusting the backrest angle: turn the ad­
ju sting wheel.
_& WARNING
-Only adjust the front seat with when the ve­
hicle is stationary. Otherwise, this increases
the risk of an accident
- Exercise caution when adjusting the seat
height. Adjusting the seat carelessly or
without checking can pinch hands and fin­ gers.
- The front seat backrests must not be tilted
too far back when driving, because this im­
pairs the effectiveness of the safety belts
and airbag system, which increases the risk
of injury.
Power seat adjustment
Applies to vehicles: with power adjustable seats
Fig . 52 Front seats: power seat adjustme nt
@ -Adjusting the lumbar support: press the but­
ton in the applicable position.
@ -Moving the seat up/down: press the button
up/down. To adjust the front seat cushion, press
IJJI,

Intelligent Technology
When the hill descent assist is on, the current
driving speed, when your vehicle entered the in­
cline is maintained. It is only possible to switch
on the assist when driving slower than 37 mph (60 km/h). The assist works between approxi­
mately 2 and 19 mph (4 and 30 km/h). The driver
can increase or decrease the vehicle speed within
these limits by depressing the accelerator or brake pedal.
There must be however sufficient ground adhe ­
sion . The hill descent assist
cannot do its job if
the incline is icy or if the incline ground is loose
¢ ,&.
Active assistance at a specific speed up to about 19 mph (30 km/h) is shown in the instrument
cluster through a blinking indicator light •. The
indicator light shines continuously when in the
ready mode.
The system does not work at speeds between 19
and 37 mph (30 and 60 km/h) . The system is
then in the ready-mode. This is shown through
the LED turned on in the button . The system au­
tomatically switched off when you drive faster
than 37 mph (60 km/h). The LED will also go out
in this scenario.
Hill descent assist is automatically activated un­
der the following conditions:
- The LED in the button turns on ,
- the vehicle speed is lower than 19 mph (30 km/
h) ,
-the incline angle is at least around 10% .
A WARNING
-Always adapt your speed to the weather ,
road and traffic conditions . Do not let the
increased safety provided tempt you into
taking risks, because this increases the risk
of an accident.
- The hill descent assist system cannot over­
come the laws of physics. Your driving style
must always be adapted to the current road
and traffic conditions.
- The hill descent assist may not be able to
hold your vehicle at a constant speed under
all conditions while driving on an incline (for
154
example if ground under the vehicle is
loose).
Brakes
New brake pads
New brake pads do not achieve their full braking
effect during the first
250 mi (400 km). They
must be "broken in" first¢& . However, you can
compensate for the slightly reduced braking
force by pressing firmly on the brake pedal. Avoid heavy braking during the break-in period.
Operating conditions and driving habits
The brakes on today's automobiles are still sub­
ject to wear, depending largely on operating con­
ditions and driving habits¢,& . On vehicles that
are either driven mostly in stop-and-go city traf­
fic or are driven hard, the brake pads should be checked by your authorized Audi dealer more of ­
ten than specified in the
Warranty & Mainte­
nance booklet.
Failure to have your brake pads
inspected can result in reduced brake perform­
ance.
On steep slopes, you should use the braking ef­
fect of the engine. This way, you prevent unnec­
essary wear on the brake system. If you must use
your brakes, do not hold the brakes down contin­
uously. Pump the brakes at intervals.
Operating noise
Noises may occur when braking depending on the
speed, braking force and outside conditions such
as temperature and humidity.
Effect of water or road salt
In certain situations, for example after driving
through water, in heavy rain, after overnight con­ densation or after washing your car , the braking
effect can be reduced by moisture or ice on the
brake rotors and brake pads. The brakes must be
"dried" first with a few careful brake applica­
tions.
At higher speeds and with the windshield wipers
turned on, the brake pads press against the brake
rotors for a short amount of time. This action
which is not felt by the driver happens at regular .,.

intervals and fac ilitat es a better reaction time for
the brak es in wet weather.
The braki ng effect can also be red uced if you are
driving on salted roads and you do not apply the b rakes for long periods of time . The layer of salt
on th e brake rotors and brake pads must be worn
off first when the brakes are applied~&, .
Cor ro sion
Leaving the vehicle par ked for long periods of
time, low m ileage and avo iding heavy brak ing
can contribute to corros ion on the brake rotors
and dirty brake pads.
If you usually avo id heavy b raking or if there is
cor ros io n present , occasional heavy braking at
high speeds is recommended to clean the brake
rotors and pads~&, .
Brake system malfunct ion
if you notice that the bra ke pedal travel has sud­
denly
go tten larger , the n a brake circu it may have
failed ~&. .
Low brake fluid level
When the brake flu id level is low , malfunct ions in
the brake system may occ ur. The brake flu id leve l
i s elect ronically mo nitored .
Brake booster
The brake booster amplifies the pressure you ap­
p ly to the brake pedal.
It only works when the en ­
g ine is running ~&, .
Brak e lining we ar status
Brake lining wea r may be checked by visual in­
spection of the condition of the brake pads
through the open ings in the wheel. If necessary,
the wheel may be removed for this inspection
~ page 213, Replacing wheels .
.8, WARNING
-New bra ke pads don 't have the best stop­
ping power and must be "bro ken- in" dur ing
the init ial 250 m iles ( 400 km). Yo u can
compensate for this by p ressing the brake
peda l more firm ly . T his also applies later
when new pads are installed .
Intelligent Technology
- You shou ld pe rform braking maneuvers for
the purpose of cleaning the brake system
only if road condit ions permit . Other road
users must not be put at r isk -you may
cause an accident!
- Before descending a steep grade, reduce
speed and sh ift tra nsmission in to a lower
gea r or lower dr iving range . Do not r ide the
b rakes or hold the pedal down too long or
too often. Th is co uld cause t he b rakes to ge t
hot and dim inish b raking effic ien cy.
- D o not " ride the bra kes " by rest ing you r foot
on the ped al when you do no t intend to
brake . T his may ca use the brakes to ove r­
heat, premature wear and increased stop ­
ping distance .
- Under cer tain clima tic and ope rating condi­
tions such as passing t hrough water, driving
in heavy rain o r after washing the vehicle,
the effectiveness of the brakes can be re­
duced. In winter, ice can accumu late on the
brake pads, lin ings, discs and drums . Care­
fully apply brakes for a test . Brakes will d ry
and ice coat ings will be cleaned off after a
few ca refu l bra ke applications .
- Driving for an extended period of t ime on
salt-covered roads without using your b rakes can also affect braking eff icien cy.
Clea n off acc umulated salt coat ing fr om
b rake discs an d pads w ith a few careful
brake applicat ions .
- If you damage the front s poile r, or if you in­
s t all a different spoiler, be s ure the a ir flow
to the front brakes is not obstructed. Other­
wise the brake system could overheat reduc­
ing the effectiveness of the ent ire brake sys­
tem.
- Fai lu re of one brake circ uit w ill impa ir the
braking capability resulting in an increased
stopping distance . Avoid driving the vehicle
and have it towed to the nearest authorized
Aud i deale r or qualified worksho p.
- Never let the ve hicle roll to a stop with the
e ngine shut off.
- If the brake booster is not working, the
brake pedal must be pressed cons iderab ly
harder to make up for the lack of booster
assis tance .
155

Driving and th e en vironm ent
A WARNING
-The temperature of the exhaust system is
high, both when driving and after stopping
the engine.
- Never touch the exha ust tail pipes once they
have become hot . This could result in burns.
- Do no t park or operate the vehi cle in areas
where the hot exha ust system may come in
contact with dry grass, br ush, fue l spill or
other mater ial which can cause a fire.
- Do not apply additional undercoating or
rustproofing on or near the exhaust mani­
fold, exhaust p ipes, catalytic converter or
heat sh ields. During dr iv ing, the substance
used for undercoating could ove rheat and
ca use a fire .
(D Note
-Be aware that just one tank filling with
leaded fuel will a lready ser iously degrade
the performance of the catalytic converter .
- Do not exceed the correct eng ine oi l level
¢ page 181.
-Do not drive until the fuel tank becomes
complete ly empty. The engine cou ld mis­
fire. Unburned fuel could also get into the
exhaust system and this could cause t he
catalytic converte r to overheat.
- Do not turn off the ignition whi le the vehicle
i s mov ing.
- Do not continue to operate your veh icle un­
der these cond itions, as otherwise fue l can
r each the catalytic converte r. This cou ld re­
su lt in ove rheating of t he converte r, req uir ­
i ng its re placement.
- T o assure efficient operation of the Emis­
s ion Control System:
- Have your ve hicle maintained properly and
in accordance with the se rvice recommen ­
dations in your Wa rranty
& Maintenance
book let .
- Lack of proper maintenance as well as im­
proper use of the vehicle will impair the
function of the em ission cont rol system
and co uld lead to damage.
160
-
® For the sake of the environment
Even when the Emiss ion Control System is op­
e rating properly, the exhaust gas can have a
su lfu r-li ke exhaust gas sme ll under some op­
erating states. T his depends on the sulfur
content of the fuel being used. Us ing a d iffer­
ent brand of fuel may help, or fi lling the tank
with lead-free super g rade gasoline.
Shutting down vehicle
If you would like your vehicle to remain inopera­
tive for a longer pe riod of time, contact an Audi
o r othe r spec ia liz ed dealer. They ca n adv ise you
o n necessa ry p recautions e.g. corros io n preven­
tion, m aintenance and storage . Pay attention to
additional in formation concer ning the battery .
Refer to¢
page 187 .
Economical and environ­
mentally-friendly driving
General
Your personal style of driving will determine the
economy of your vehicle, a s well as exhau st and
noise levels .
Fu el economy, env ironmenta l impact, and wear
o n your e ngine, brakes and tires large ly depend
o n t hree fa ctors:
- your personal d riving style
- operat ing cond itions
- technical limitat ions
If you anticipate what you need to do next and
drive economically, you can easily cut your f uel
consumption by 10-lS percent. Th is sect ion wi ll
give you some tips on how you can help the envi­
ronment and your pocketbook .
{l) Tips
The consumption estimates as published by
ENVIRONMENTAL PROTECTIO N AGENCY
(EPA) and T ransport Canada may not corre­
spond to your actual consump tion on the
r oad, which wi ll vary depending upon vehicle
l oad and speed, road a nd wea ther conditions,
tri p l engt h, etc.

Drive smoothly and keep a lookout ahead
Vehicles use the most fuel when they are acceler­
ating .
11-Avoid unnecessary accelerating and braking.
Vehicles use the most fuel when they are acceler­ ating . If you anticipate what is going to happen
next, you will need to brake less and, thus, accel­
erate less . Let the vehicle coast whenever possi­
ble - for example when you see that the next traf ­
f ic light is red .
Avoid full throttle
Driving a t modera te speeds saves fuel and im­
proves your mileage .
11-Try and keep well be low your car's max imum
speed.
Accelerating gent ly reduces fuel consumption,
engine wear, and does not disturb the environ ­
ment.
F ue l cons umption, exha ust emissions and engine
noise increase disproportionately at high speeds.
If you drive at approximately three quarters of
top speed, fuel consumpt ion will be reduced by
one half. Never drive faster than the posted
speed limit and weather conditions permit.
Reducing unnecessary idling
Even when your car is just idling i t burns up fuel.
11-S hut the engine off w hen you are not driving
the vehicle.
11-Do not warm up the vehicle by letting the en-
gine ru n at idle .
It makes sense to shut off the eng ine in traffic
jams, when wa iting for trains to pass at rai lroad
crossings, or at traffic lights that have long waits
on red . Turn ing the eng ine off for just 30 -40 sec ­
onds saves more fue l than is bu rned starting the
engine agai n.
It takes a long t ime for the engine to warm up
fu lly when it is runni ng at idle . However, wear
and noxious emiss ions are especially high when
the eng ine is wa rm ing up . So you should d rive
Driving and the envir onment
away as soon as you start the eng ine and avoid
running at high rpms w hil e the engine is sti ll
warming up .
(D Note
Do not leave eng ine idling una ttended after
starting. If wa rning lights shou ld come on to
i ndicate improper operation, they would go
unheeded. Extended idling also prod uces
heat, which could result in overheating or
other damage to the vehicle or other proper ­
ty .
Regular maintenance
A badly tuned engine unnecessarily wastes a lot
of fuel .
11-Have your vehicle serviced at regular interva ls.
By having your vehicle regular ly serv iced by an
authorized Audi dea ler helps to ensure that it
runs properly and economically. The cond ition of
your vehicle not only affects its safety and ability
to hold its value, it also affects
fuel con sump­
tion .
Chec k your oil each t ime you fill your tank.
T he amount o f oi l used is related to engine load
and speed.
It is normal fo r the oil consump tion of a new en­
gine to reach its lowest value after a ce rtain m ile­
age has been dr iven.
You m ust dr ive your ve hicle about 3,000 m iles
(5,000 kilometers) befo re yo u can prope rly as­
sess oil consumpt io n.
T h is also app lies to fuel consumption and eng ine
output.
(D Note
- Have your vehicle maintained properly and in accordance with the se rvice recommenda­
tions i n your Warranty
& M aintenance book-
le t. La ck of prope r maintenan ce as we ll as
imp roper use of the ve hicle will im pair the
function of the em ission cont rol sys tem and
co uld lead to damage . .,.
161

Trailer mod e
Weight d istribution
Towing a loaded trailer with an empty car res ults
in a high ly unstable distribution of weight . If this
cannot be avoided, drive at very low speeds on ly
to avoid the risk of losing steering control.
A "balanced" rig is easie r to operate and con trol.
This means that the tow vehicle should be loaded
to the extent possible and permissible, while
keeping the trai le r as light as possib le under the
circumstances. Whenever possible, transfer
some cargo to the luggage compartment of the
tow vehicle while observ ing tongue load requ ire­
ments and vehicle loading considerat ions.
Spee d
The higher the speed, the more difficult it be­
comes for the driver to contro l the rig. Do not
drive at the maximum permiss ible speed. Reduce
your speed even more if load, weather or w ind
conditions are unfavorable - part icularly when
goi ng downhill.
Reduce veh icle speed
immediatel y if the tra iler
shows the slightest sign of swaying .
Do not try
to stop the sway ing by acc ele rating .
Observe speed lim its. In some areas, speeds for
veh icles towing trailers are lower than for regular
ve hicles.
A lways app ly brakes early. When driving down­
h ill, shift into a lower gear to use the engine
braking effect to slow the veh icle. Use of the
brakes alone can cause them to overheat and fail.
Coolant temp era ture
The coolant temperature gauge¢ page 10 must
be observed carefully. If the needle moves close
to the upper end of the scale, reduce speed im­ mediately and/or turn off the air conditioner.
If the coo lant temperature warning light in the
instr ument cluster starts flashing., pull off
the road, stop and let the engine
idle for about
two minutes to prevent heat bu ild-up.
A WARNING
Anyone not proper ly restrained in a moving
vehicle is at a much greater risk in an acci-
166
-
dent . Never let anyone ride in your car who is
not properly wear ing the restraints provided
by Audi.
Trailer mode notes
Important to know
You r vehicle handles differently when towing a
trailer because o f th e additiona l weight and dif­
ferent weight distribution. Safety, performance
and economy will g reatly depend on how carefu l­
l y you load your trai ler and operate your rig.
Before yo u actually tow your trailer, pract ice
turning, stopping and backing up in an area away
from traffic . Keep practicing unti l you have be­
come complete ly familiar w ith the way your vehi­
cle-tra iler combination behaves and responds.
Backing up is difficult and requires practice .
Backing up with a trailer genera lly requires steer­
ing action opposite to that when backing up your
vehicle without a trailer.
Maintain a greater distance between your vehicle
and the one in fro nt of you . You will need more
room to stop. To compensate for the trailer, you
will need a larger than normal turning radius.
When passing, remember that you cannot accel­ erate as fast as you normally wo uld beca use of
the added load. Make sure you have enough room
to pass. After passing, allow p lenty of room for
your trailer before changing lanes again.
Avoid jerky starts, sharp turns or rapid lane
changes.
@ Tips
- Do not tow a trailer du ring the break-in peri­
od of your vehicle.
- If you tow a trai le r, your Au di may requi re
more frequent maintenance due to the ex­
t ra load ¢
page 232.

Checking and Filling
-Keep children away from the engine com­
partment.
- Never spill fluids on hot engine compo­
nents. They can cause a fire.
- Never touch the radiator fan. The auxiliary
electric fan is temperature controlled and
can switch on suddenly.
- Never open the coolant reservoir cap when
the engine is still warm. The coolant system
is pressurized and hot coolant could spray
out.
- Protect your face, hands and arm from steam or hot engine coolant by placing a
thick rag over the cap when you open the
coolant reservoir .
- Do not remove the engine cover under any
circumstances. This increases the risk of
burns .
- If work on the fuel system or the electrical
system is necessary:
-Always disconnect the battery.
- Never smoke or work near heaters or open
flames. Fluids in the engine compartment
could start a fire.
- Keep an approved fire extinguisher imme­
diately available.
- To avoid electrical shock and personal injury
while the engine is running or being started,
never touch:
- Ignition cables
- Other components of the high voltage
electronic ignition system.
- If you must perform a check or repair with
the engine running:
- First, fully apply the parking brake, move
selector lever of automatic transmission
to "P" (Park).
- Always use extreme caution to prevent
clothing, jewelry, or long hair from get-
178
ting caught in the radiator fan, V-belts or
other moving parts, or from contacting
hot parts. Tie back hair before starting,
and do not wear clothing that will hang or
droop into the engine.
- Minimize exposure to emission and chemi­
cal hazards
c::> & .
A WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain or
emit chemicals known to the State of Cali­
fornia to cause cancer and birth defects and
reproductive harm. In addition, certain flu­
ids contained in vehicles and certain prod­
ucts of component wear contain or emit
chemicals known to the State of California
to cause cancer and birth defects or other
reproductive harm .
- Battery posts, terminals and related acces­
sories contain lead and lead compounds,
chemicals known to the State of California
to cause cancer and reproductive harms.
Wash hands after handling.
([) Note
When adding fluids, always make sure that
they are poured into the proper container or
filler opening, otherwise serious damage to
vehicle systems will occur.
@ For the sake of the environment
To detect leaks in time, inspect the vehicle
floor pan from underneath regularly. If you
see spots from oil or other vehicle fluids, have
your vehicle inspected by an authorized Audi dealer .

@ For the sake of the environment
Because of the problem of proper disposal of
brake fluid as we ll as the special toots re­
quired and the necessary expertise, we rec­
ommend that you have the brake fluid
changed by your authorized Audi dealer .
Battery
General information
Under normal operating conditions, the battery
in your Audi does not need any maintenance.
With
high outside temperatures or long daily
drives we recommend that you have the electro­
lyte level checked by an authorized Audi dealer or
qualified workshop. The electrolyte level should
also be checked each time the battery is charged
c> page 189.
Have the battery checked when you take your ve­
hicle in for serv ice. You are well advised to re­
place a battery t hat is older than 5 years.
With certain types of airbag deployment, the battery is disconnected from the vehicle electri­
cal system for safety reasons
c> & in Repair, care
and disposal of the airbags on page 125 .
Disconnecting the battery terminals
Some vehicle functions (power window regula­
tors, for example) are lost if the battery termi­ nals are disconnected. These functions have to be
relearned after the battery terminals are con­
nected again. To prevent th is, the battery should
only be disconnected from the vehicle e lectr ica l
system when abso lutely necessary for repairs.
Vehicles not driven for long periods
If you do not drive your vehicle over a period of
several days or weeks, electrical components are
gradually cut back or sw itched off. This reduces
energy consumption and maintains starting ca­
pability over a longer pe riod
c> page 157.
Some of the conven ience functions may not oper­
ate, such as the interior lights or the power seat
adjustment. The convenience functions will be
available again when you turn on the ignition and
start the engine.
Checking and Filling
Winter operation
During the winter months, battery capacity tends
to decrease as temperatures drop . This is be­
cause more power is also consumed while start­
ing, and the headlights, rear window defogger,
etc., are used more often.
Avo id unnecessary power consumption, particu­
larly in city traffic or when traveling only short
distances . Let your authorized Audi dealer check
the capacity of the vehicle battery before winter
sets in
c> page 189. A well charged battery will
not only prevent starting problems when the
weather is cold, but will also last longer .
(D Tips
If your vehicle is left standing for several
weeks at extremely low temperatures, the ve­
hicle battery should be removed and stored
where it w ill not freeze. This will prevent it
from be ing damaged and having to be re­
placed.
Working on the battery
Be especially careful when working on or near
the battery.
The battery is located in the engine compart­
ment . Before you check anything in the engine
compartment ,
read and heed all WARNINGS
c>,& ,
Always heed the safety warnings, when working
on the vehicle battery or the veh icle electrical
system to prevent injury.
The following WARNINGS are very important
when working on the battery:
Always heed the following WARNING SYM·
BOLS and safety precautions when working on
the battery.
®
Always wear eye protection.
A
Battery acid contains sulfuric acid. Al-
ways wear gloves and eye protection .
187