2016 AUDI Q3 Door

Opening and closing
"'To set a position between opened and closed,
press/pull the button ~ up to the first level
u nt il the desired position is reached.
@ Sliding the roof
"'To open the sunroof completely , slide the but­
ton
l""-I back up to the second level.
"'T o close the sunroof comp letely, slide the but­
ton
l""'I forward briefly to the second level 9 &, .
"'To set a position between opened and closed,
slide the button~ forward/back up to the first
level until the des ired position is reached.
© Opening/closing the sun shade
"'To complete ly open the sun shade, briefly press
the right button.
"' To comp letely close the sun shade, briefly press
the left button.
"' To stop the sun shade, press the corresponding
button again.
After the ignition is switched off, you can still op­
erate the panoramic sunroof for about 10 mi­ nutes . The sw itch is deactivated once the driver's
or front passenger's door is opened .
A WARNING
Be careful when clos ing the panoram ic sun­
roof- otherwise serious injury could result!
For this reason, always remove the ignition
key when leaving the vehicle.
@ Note
Always close your panoram ic sunroof when
leaving your vehicle. Sudden ra in can cause
damage to the interior equ ipment of you r ve­
hicle, particularly the electronic equipment.
@ Tips
-For informat ion about convenience open­
ing /closing, refer to
9 page 37.
-The panorama roof will only open dow n to
-4 Of (-20 °().
Emergency closing the roof
If an object is detected when closing, the panora­
ma roof will open again automatically. In this
38
case, you can then close it with the power emer ­
gency closing function.
"' Pull the respective button
¢ page 3 7, fig . 34
withi n 5 seconds after the roof opens automati­
cally and hold until the panorama roof is
closed.

Lights and Vision
(D Tips
-The light sensor for the automatic head­
lights* is in the rearview m irror mount.
Therefore, do not place any stickers in this
area on the windshield.
- Some of the exterior lighting functions can be adjusted
c:-page 41.
-If you turn off the ignition wh ile the exter ior
lights are on and open the door, you will
hear a warning tone.
- In cool or damp weather, the inside of the
headlights, turn s ignals and tail lights can
fog over due to the temperature d ifference
between the inside and outs ide . They will
clear short ly after sw itch ing them on . This
does not affect the serv ice life of the light­
ing .
Turn signals and high beam lever
The lever operates the turn signals, the high
beams and the headlight flasher.
8 N 0
~
F ig . 36 Turn s ig nal and h ig h bea m lever
Turn signals ¢ Q
With the ignition on, the signal lights w ill blink if
the lever is in the corresponding position.
(!) -righ t turn signal
@ -left turn s ignal
The turn s ignal blinks three times if you just tap
the lever.
High beam s and headlight flasher ~D
Move the lever to the co rrespo nd ing posit ion:
@ -high beams on (ve hicles w ith high beam as­
sis t*
c:-page 40
40
@ -high beams off or headlight flasher
The ind icator light
II in the instrume nt cl uster
turns o n.
Notes on these features
- The turn signals only work w ith the ignition
turned on . T he indicator lights . or
II in the
instrument cluster also bli nk.
- After you have tu rned a corner, the tu rn signa l
sw itches off automat ica lly .
- The
high beam works only when the head lights
are on . Th e ind icator light
Bl in the instrumen t
cl uste r ill um ina tes when the high beams a re
on.
- The
headlight flasher works o nly as long as yo u
hold the leve r - even if there are no lights
sw itched on . The ind icator light
II in the in­
s trumen t clus te r i lluminates whe n you use the
head light flasher.
&_ WARNING
D o not use t he high beam or head light f lasher
if you know that these could blind oncoming
traffic.
Headlight assist
Applies to vehicles: wit h headlight assistant
The headlight assistant automatically turns the
high beams on or off depending on the surround­
ing conditions .
Fig. 3 7 Turn s ig nal a nd hi gh beam lever: Tu rnin g headl ig ht
ass istant on/off
Activating headl ight assi stant
Requireme nt: the light sw itch must be in the AU -
TO positio n. .,.

~ To activate the headlight assistant, tap the lev ­
er forward (!). The indicator light
ii appears
in the instrument cluster disp lay and the head­
lights are switched on/off automatically. The
SI indicator light also turns on if the high
beams are switched on .
Switching the high beams on/off manually
If the high beams did not switch on/off automat­
ically as expected, you may switch them on or off
manually instead:
~ To switch the high beams on manually, tap the
l ever forward (!). The
SI indicator light turns
on.
~ To switch the high beams off manually, pull the
lever back@. The headlight assistant is deacti­
vated .
Operating the headlight flasher
~ Pull the lever into position @to operate the
headlight flasher when the headlight assist is
activated. The headlight ass istant remains ac­
tive.
Messages in the instrument cluster display
Headlight assist: System fault!
Drive to an authorized Aud i dea ler or a uthorized
Aud i Serv ice Fac ility immediately to have the
malfunction corrected. You can still switch the
high beams on or off manually.
Headlight assist: Unavailable. No camera view
The camera view is blocked, for example by a
sticker or debris .
The sensor is located between the interior rear­
view mirror and the windshield . Therefore, do not
place any st ickers in this area on the windshield .
A WARNING
Headlight assistant is only intended to assist
the driver. The driver is still responsible for
controlling the headlights and switching
them manually depending on light and visibil­
ity conditions. It may be necessary to operate
them manually in situations such as:
- In adverse weather conditions such as fog,
heavy ra in, b lowing snow or spraying water.
Lights and Vision
-On roads where oncoming traffic may be
partially obscured, such as expressways.
- When there are road users that do not have
sufficient lighting, such as bicyclers or
veh icles with dirty tail lamps.
- In tight curves and on steep slopes.
- In poorly lit areas.
- With strong reflectors, such as signs .
- If the area of the windshield near the sensor
is fogged over, dirty, icy or covered with a
s ticker.
Adjusting exterior lighting
The functions are selected in the radio or MMI*.
~ Select: !CAR ! function button> (Car) Systems*
control button > Vehicle settings> Exterior
lighting .
Coming home (lights when leaving car}*,
Leaving home (lights when unlocking car)*
The coming home function illumi nates the area
around the vehicle when the ignition is switched
off and the driver's door is opened. Depending on
vehicle eq uipment, the function can be switched
on and off or the length of time the lights remain
on* can be adjusted .
T he
leaving home function illuminates the area
around the vehicle when unlock ing it. Thi s func­
tion can be switched on and off.
The
coming home and leaving home functions
only operate when it is dark and the light switch
is i n the AUTO posit ion ~
page 39, fig. 35.
Daytime running lights
USA models:
You can switch the daytime running
l ights
on and off .
Canada models:
The function cannot be turned
off. It is activated automatically each time the ig­
nition is switched on .
41

Lights and Vision
Emergency flashers
Fig. 38 Cente r console: eme rge ncy flasher sw itc h
The emergency flashers makes other motorists
aware that you or your vehicle are in an emergen ­
cy s ituation .
.. Press the switch
l1J c> fig. 38 to turn the emer-
gency flashers on or off.
When the em ergency f lashers are on , a ll four
turn signals blink at the same time. The turn sig­
na l indicator lights
BIB in the instrument clus­
ter, as well as the light in the emerge ncy flasher
sw itch ~ blink likewise .
You can indicate a lane change or a turn when the emergency flashers are sw itched on by using the
turn sig nal lever . The emergency flashers stop
temporar ily.
The emergency flashers also wo rk when the igni­
tion is turned off.
The emergency flashers wi ll tur n on a utomat ica l­
ly if you are in an accident where th e airbag has
dep loyed.
@ Tips
You s hou ld t urn on the emergency flashers
when :
-you are the last veh icle standing in a traffic
j am so that any other ve hicles coming can
see you, o r when
- your ve hicle has broke n down or you are in
an emergency situation, o r when
-your ve hicle is being towe d by a tow truck or
if you are towing another vehicle behind
you.
42
Interior lighting
Front/rear interior lighting
Fi g. 39 Front head liner: interio r li ghtin g con trols
Fi g. 40 Rea r h eadl iner: LED re ad in g li ghts•
Press t he applicable button :
~ -Inter io r l ight ing on/off
[!] . Door cont act swi tch on/off . T he inter io r li ght­
i ng is controlled automa tic a lly .
~- Reading lights* on/off
Interior lighting
There are ot her inter ior light ing f unct ions that
are avai lable. Some funct ions can be adjusted in
the MMI. Select:
l cAR ! function button > Car sys ­
tems *
contro l butto n > Vehicle settings > Interi­
or lighting .

Lights and Vision
@ Tips
If the power adjusting function malfunctions,
the glass in both mirrors can be adjusted by
pressing on the edge of it by hand.
Dimming the mirror
Your vehicle is equipped with o manual or auto­
matic dimming rearview mirror.
Fig. 43 Automatic dimming rearview mirror•
Manual dimming rearview mirror*
....
0 0
> u. Ill
• Pull the lever on the bottom of the mirror back .
Automatic dimming rearview mirror*
• To switch the dimming function on or off, press
the button @. If the ind icator light @ turns
on, the inter ior and exterior mirrors* will auto­
matically dim when light shines on them (for
example, headlights shining from the rear).
A WARNING
Electrolyte fluid can leak from automatic dim­
ming mirrors if the glass is broken. Electro­
lyte fluid can irritate skin, eyes and respirato­
ry system.
- Repeated or prolonged exposure to electro­
lyte can cause irritation to the respiratory
system, especially among people with asth­
ma or other respiratory conditions. Get
fresh air immediately by leaving the vehicle
or, if that is not possible, open windows and
doors all the way.
- If electrolyte gets into the eyes, flush them
thoroughly with large amounts of clean wa­
ter for at least 15 minutes; medical atten­
tion is recommended.
44
- If electro lyte contacts skin, flush affected
area with clean water for at least 15 mi­
nutes and then wash affected area with
soap and water; medical attention is recom­ mended . Thoroughly wash affected clothing
and shoes before reuse.
- If swallowed and person is conscious, rinse mouth with water for at least 15 minutes.
Do not induce vomiting unless instructed to
do so by medical professional. Get medical
attention immediately.
(D Note
If the glass on an automatic dimming mirror
breaks, electrolyte can leak out. This liquid
damages plastic surfaces. Clean this liquid as
quickly as possible, for example with a wet
sponge.
(0 Tips
- If the dimming function is switched off for
the interior lights, the exterior lights will al­
so not be dimmed.
- If the light reaching the rearview mirror is
obstructed, the automatic dimming mirror
will not function correctly,
- The automatic dimming mirrors do not dim
when the interior lighting is turned on or
the reverse gear is selected.
Sun visors
Fig. 44 Drive r's side ; s un visor
The sun visors for the driver and front passenger
can be released from their retainers and turned
toward the doors
(D. The sun visors can also be
moved* back and forth lengthwise in this posi-
tion. ..,.

.... N
c:i ::J CX)
.... I.Cl U"I
N I.Cl ......
scald ing burns . Spilled hot liquid can also
cause an accident and personal injury .
- Use only soft c ups in the cupholder . Hard
c u ps and g lasses can cause injury in an acci­
dent .
- Never use the cup holde r or adapter as an
ashtray -risk of fire.
CD Note
Ma ke sure your bever age container has a lid .
If not, yo ur beverage could spill a nd cause
damage to vehicle equipment or stain the
seat covers.
Cup holders in the door pockets
A cup hold er is located in all four doors.
F ig . 63 Sect io n of doo r trim : cup ho lde r
The cup holder in the door pockets can fit 1 to
1.5 liter bott les .
A WARNING
Spilled h ot l iquid can cause a n accident and
p ersonal i njury.
- Never carry any beverage con taine rs wi th
hot li quids, s uch as ho t coffee or ho t te a in
I
the ve hicle while it is moving. I n case of a n
acciden t, sud den braking or o ther vehi cle
movement, hot liq uid could s pill, causing
sca ld ing burns . Spilled hot liquid can also
cause an accident and perso nal in jury.
- Use only soft c ups in the c upholder . Hard
c u ps and g lasses can ca use inj ury in an acci­
dent .
-
Seats and storag e
CD Note
Make su re your beverage contai ner has a lid.
If not, your beve rage co uld sp ill and cause
damage to vehicle eq uipment or sta in the
seat covers.
Glove compartment
T he glove compartment is illuminated*, cooled*
and can be locked* .
Fig. 64 Glove co mpart ment
Fig . 65 Glove co mpart ment: Sw itch for t he coo ling
To open glove compartment
"'Pull the handle in the direction of the arrow
¢ fig. 64 and swing the cover dow n to open.
To close glove compartment
"' Push the glove compartment lid upward unti l
the lock engages .
To switch the cooling on
"'Tu rn the rotary switch @ counter-clockwise to
sw itch the cooling on. The symbols on the rota ­
ry switch must be displayed c> fig . 65 accord-
ing ly.
Iii>
55

Seats and storage
To switch the cooling off
.,. Turn the rotary switch @clockwise to switch
the cooling off.
The cooling box works only in the cooling mode.
If the climate control is in the heating mode, we
recommend switching the cooling box off.
& WARNING
To reduce the risk of personal injury in an acci­
dent or sudden stop, always keep the glove
compartment closed while driving.
Additional storage
There are a variety of storage compartments and
fasteners in various places in the vehicle.
- In the front center console.
- At the front end of the front seats*. You can
store objects weighing up to 3.3 lbs (1.5 kg) in
the drawer and objects weighing up to 2.2 lbs (1 kg) in the hinged compartment.
- In the door trim.
- Coat hooks next to and above the rear doors.
- Nets* on the backrests of the front seats.
- Coat hooks/retaining hooks in the luggage
compartment.
& WARNING
- When driving, do not leave any hard objects
on the rear window shelf or allow your pet
to sit on the shelf. They could become a haz­
ard for vehicle occupants in the event of
sudden braking or a crash.
- Always remove objects from the instrument
panel. Any items not stored could slide
around inside the vehicle while driving or
when accelerating or when applying the
brakes or when driving around a corner.
- When you are driving make sure that any­
thing you may have placed in the center con­
sole or other storage locations cannot fall
out into the footwells. In case of sudden
braking you would not be able to brake or
accelerate.
- Any articles of clothing that you have hung
up must not interfere with the driver's view.
56
The coat hooks are designed only for light­
weight clothing. Never hang any clothing
with hard, pointed or heavy objects in the pockets on the coat hooks. During sudden
braking or in an accident - especially if the
airbag is deployed - these objects could in­
jure any passengers inside the vehicle.
- To reduce the risk of personal injury in an
accident or sudden stop, always keep the
glove compartment closed while driving.
- Read and follow all WARNINGS
~ page 128, Important safety instructions
on the side airbag system.
-Hang clothes in such a way that they do not
impair the driver's vision.
- The coat hooks must only be used for light­
weight clothing. Do not leave any heavy or
sharp edged objects in the pockets which
may interfere with the side curtain airbag
deployment and can cause personal injury in
a crash.
- Do not use coat hangers for hanging cloth­
ing on the coat hooks as this can interfere
with proper deployment of the side curtain airbags in an accident.
- Do not hang heavy objects on the coat
hooks, as they could cause personal injury in
a sudden stop.
- Always keep the compartment above the
rearview mirror closed while driving to re­
duce the risk of injury in the event of sudden
braking maneuvers or a collision.
(D Note
Objects located on the rear shelf that rub
against the rear window could damage the heating wires for the rear window defogger.
(D Tips
-A vent slot is located between the shelf and
the rear window. Do not block the vent with
any items you may place on the rear window
shelf.
- Do not place bulky items on the rear window shelf as they could restrict or block the driv­
er's vision in the rear view mirror.

Installing
• Place both sides of the cover into the mounts
on the side trim.
• Push the cover downward until both sides click
into place.
Storing*
Depending on the vehicle equipment, you can
store the cover under the cargo floor
¢page 61.
A WARNING
-To reduce the risk of accidents, the luggage
compartment cover should never be unse­
cured under any circumstances .
- The luggage compartment cover is not a
surface for storing objects. Objects placed
on the cover could endanger all vehicle oc­
cupants during sudden braking maneuvers
or in a crash.
CD Note
To avoid damage, let the luggage compart­
ment cover roll up slowly after removing.
Increasing the size of the luggage
compartment
The rear seat backrests can be folded forward ei­
ther separately or together .
Fig. 69 Backrest: release lever
Folding the backrest forward
• Pull the release lever @in the direction of the .... N arrow and fold the backrest forward. c:i ::J CX)
.... I.Cl U"I
N I.Cl ......
Seats and storage
Folding the backrest back into the upright
position
• Fold the backrest back up again until it latches
and the red marking ® is no longer visible
¢ ,&..
A WARNING
--The backrest must always be securely latch-
ed so that the safety belt of the center seat­ing position can work properly to help pro­
tect the occupant.
- The backrest must be securely latched in po­
sition so that no items contained in the lug­
gage compartment can slide forward upon
sudden braking.
- Always check whether the latch is fully en­
gaged by pulling the seatback forward.
- Never allow safety belts to become dam­
aged by being caught in door or seat hard­
ware.
- Torn or frayed safety belts can tear and
damaged belt hardware can break in a
crash. Inspect the belts periodically. Belts
showing damage to webbing, bindings,
buckles, or retractors must be replaced.
CD Note
- If you move the front seat back when the
rear seat backrest is folded forward, you
could damage the head restraints on the
rear seat.
- Make sure the seat belt is not pinched or
damaged when the rear seat backrest if
folded back. Other objects should be re­
moved from the rear bench seat to protect
the backrest from damage.
59