2016 AUDI A8 instrument cluster

(!) Door handle
@
®
©
®
®
Audi side assist display
Power locking sw itches
Audi side assist button ........ .
A ir vents with thumbwheel
Contro l lever for:
- Turn signal and high beam
- High beam assist .......... . .
- Audi active lane assist ....... .
(J) Multifunction steering wheel with:
- Horn
- Driver's airbag .... ..... ... . .
- Driver information system but-
tons . ......... ....... ..... .
- Audio/video, telephone, naviga­
tion and voice recognition but ­
tons
- Shift paddles and~ button for
manual shifting ... ..... ... . .
@ Instrument cluster .......... . .
® Windshield washer system lever
@ Head-up Display ........... .. .
@ Buttons for:
- Start -Stop -System . ..... ... . .
- MMI display
- Electronic Stabilization Control
(ESC) .. .. ............. .. .. .
- Emergency flashers ........ . .
@ Starting the engine if there is a
malfunction ..... ....... ..... .
@ Knee airbag ................ . .
~ Buttons for:
- Steering wheel adjustment ... .
- Steering wheel heating .. .... .
@ Lever for:
- Cruise control system ..... .. .
- Adaptive cruise control .... .. .
@ Button for switching the Head-up
Display on/off, adjusting the
height .. .. ............... .. .
102
35
102
48
49
99
150
23
115 10
54
27
85
192
47
83
160
80
79
88
90
27
Cockpit
@ Instrument illumination ....... .
@ Engine hood release .......... .
@) Data Link Connector for On Board
Diagnostics (OBD II) .......... .
@ Light switch . .. .............. .
@ Buttons for :
-All-weather lights .......... .
- Night vision assistant ........ .
- Rear fog lights ............. .
@ Power exterior mirror adjustment
Rear lid switch ... ...... ...... .
Power windows .............. .
Memory function buttons ...... .
MMI display
Indicator lights/buttons for
- PASSENGER AIR BAG OFF
- Parking system ............. .
- Rear window power sun shade
@ Glove compartment .... ...... .
@ Front passenger's airbag ...... .
@ Valet parking feature ......... .
@ Analog clock .. .. ............ .
@ Climate contro ls ............. .
@) MMI controls
<.§ Selector lever (automatic transmis-
sion) . .. .. .. .. .............. .
@ Center console with cupholder .. .
@ E lectromechanical parking brake
@ IS TAR T ENGINE ST OP !button
{I) Tips
51
220
28
46
46
109
46
51
36
40
65
156
118
53
74
150
41 26
77
112 73
83
81
- Some of the equipment or features shown
in the general illustration may be standard
equipment on your vehicle or may be op­
tional equipment depending on your model.
Always ask your authorized Audi dealer if
you have a question about your vehicle.
- Operation of the Multi Media Interface
(MMI) is described in a separate manual.
9

Instruments and indicator lights
Instruments and indicator Lights
Instruments
Instrument cluster and controls
The instrument cluster is your central source of information.
Fig. 3 Overview of the instr ume nt cluster
CD Coolant temperature gauge .. .. .
@ Tachometer (engine rev counte r) .
@ Turn signals .... .. ...... ..... .
@ Display with
- Driver information system
- Warning/indicator lights
® Tachometer
@ Fuel gauge ..... ........... .. .
(J) Reset button for trip odometer
(D Tips
10
11
48
23
11
11
26
The instrument illumination (for dials and
needles) turns on when the ignition is on and
the vehicle lights are turned off. As the day­
light fades, the illumination of the dials like­
wise dims automatically and will go out com­
pletely when the outside light is very low . This
10
feature is meant to remind you to switch on
the headlights when outside light conditions
become poor.
Engine coolant temperature gauge
The engine coolant gauge CD~ page 10, fig. 3
only works when the ignition is on. To prevent
damage to your engine, please note the follow­
ing important points:
Engine cold
If only the LEDs at the bottom of the gauge turn
on, the engine has not reached operating tem­
perature yet. Avoid high engine speeds, heavy en-
gine loads and heavy throttle applications. .,,_

Normal temperature
The engine has reached its operating tempera­
ture once the LEDs up to the center of the gauge
turn on under norma l driving conditions . The
LEDs higher up may turn on when the engine is
under heavy load or the exterior temperature is
high. This is no need to worry as long as the.
warn ing light in the instrument cluster does not
illuminate . If the LEDs in the upper area of the
d isplay and the ind icator light . in the instru­
ment cluster display tu rn on , the coolant temper­
ature is too high
¢page 15.
_& WARNING
-Always observe the warning in ¢ page 220,
Working in the engine compartment,
before
opening the hood and checking the engine
coolant level.
- Never open the engine hood if you see or
hear steam, or if you see engine coolant
dr ipping from the engine compartment. You
could burn yourself. Let the engine cool off
first so that you cannot hear or see any
steam or engine coolant.
(D Note
-Mounting additional lights or accessories in
front of the air inlets reduces the cooling ef­
fect of the radiator. At h igh outside temper­
atures or high engine load, the engine could
overheat .
- The front spoiler has been designed to prop­
erly distribute the cooling air when the veh i­
cle is moving.
If the spo iler is damaged, this
could reduce the cooling effect and the en­
gine could then overheat. Ask your author­
iz ed Audi dealer for assistance.
Tachometer (engine rev counter)
The tachometer indicates the engine RPM (revo­
lutions per minutes).
If engine RPM drops below 1,500, you should
downshift to the next lower gear. The red area at
the end of the scale indicates maximum permis­
sib le eng ine RPM after the break-in period. Be­
fore reaching this area, move the selector lever
Instruments and indicator lights
to position "D (Drive)" or ease your foot off the
acce lerator pedal.
(D Note
The tachome ter needle should only briefly be
in the red zone: you could damage your en­
gine! The beginning of the red zone varies de­
pending on the engine .
@ For the sake of the environment
Upshifting early saves fuel and reduces en­
gine noise.
Fuel gauge
The fue l gauge only works when the ignition is
on. If the fuel level drops below 4 gallons (15 lit­
ers), the bottom LED turns red and the indicator
l ight tllturns on
¢page 21. The bottom LED
blinks red when the fue l level is very low .
The possible range based on the current fue l lev­
el is shown in tab@¢
page 23, fig. 4.
(D Note
Never run the tank completely dry. An irregu­
l ar supply of fuel can cause engine misfiring
and fuel could enter the exhaust system. The
catalytic converter could then overheat and
be damaged.
Indicator Lights
Description
The indicator lights in the instrument cluster
blink or turn on. They indicate functions or mal­
funct ions¢ ,&..
Messages may appear with some indicator lights.
A warning signal will sound at the same time.
The ind icator lights and messages in the center
of the displays may be replaced by other displays.
To show them again, select the tab for indicator lights and messages using the multifunction
steering wheel¢
page 23. If there are several
malfunctions, you can display them one at a time
u sin g the thumbwheel.
IJi,-
11

.... N
0 J:
'SI:
manual also appears in the instrument cluster
display and a warning tone sounds.
The brake system will still respond even with­
out the assistance of the ABS system. See your
authorized Audi dealer as soon as possible to re­
store full braking performance.
For more infor­
mation regarding the ABS ¢
page 190.
Malfunction in the brake system
If the brake warning light¢ page 14 and the ABS
warning illuminate
together there may be a mal­
function in the ABS, and there may also be a mal­
function in the brake system itself¢.&. .
The ABS
will not work and you will notice a change in
braking response and performance.
In the event of a malfunction in the brake sys­
tem
the warning/indicator light 1111 (USA mod­
els)/ . (Canada models) in the instrument clus­
ter flashes¢
page 14.
Malfunction in the electronic differential
lock (EDL)
The EDL works together with the ABS . The ABS
warning light will come on if there is a malfunc­
tion in the EDL system¢ page 190. See your au­
thorized Audi dealer as soon as possible.
A WARNING
- If the 9 (USA models)/ll] (Canada mod­
els) warning light does not go out, or if it
comes on while driving, the ABS system is
not working properly. The vehicle can then
be stopped only with the standard brakes
(without ABS). You will not have the protec­
tion ABS provides. Contact your Audi dealer
as soon as possible.
- USA models: If the 1111 warning light, the
DJ warning light and the 9warning light
come on together, the rear wheels could
lock up first under hard braking. Rear wheel
lock-up can cause loss of vehicle control and
an accident. Have your vehicle repaired im­
mediately by your authorized Audi dealer or
a qualified workshop. Drive slowly and avoid
sudden, hard brake applications.
-
.... ....
:=: 1) - : USA model s only
Instruments and indicator lights
- Canada models: If the brake warning light
. , the
Bl warning light and the ABS warn­
ing light
riJ come on together, the rear
wheels could lock up first under hard brak­
ing. Rear wheel lock-up can cause loss of ve­
hicle control and an accident . Have your ve­
hicle repaired immediately by your author­
ized Audi dealer or a qualified workshop.
Drive slowly and avoid sudden, hard brake
applications.
(0} Worn brake pads
111 Brake pads!
If the warning light illuminates, immediately
contact your authorized Audi dealer or qualified
workshop to have all brake pads inspected. On
USA models the warning light
111 comes on to­
gether with the warning light
1111 . Both sets of
brake pads on an axle must always be replaced at
the same time.
A WARNING
-
Driving with bad brakes can cause a collision
and serious personal injury.
- If the warning light
111 and the warning
light
llll1l with the message Brake pads!
comes on in the instrument cluster display,
immediately contact your authorized Audi
dealer or qualified workshop to have all
brake pads checked or replaced if necessary.
EPC Electronic power control
Applies to: veh icles w ith gasoline engine
This warning/indicator light monitors the elec­
tronic power control.
The~ warning/indicator light (Electronic Power
Control) illuminates when you switch the ignition
on as a function check .
(D Tips
If this warning/indicator light illuminates
while you are driving, then there is a malfunc-
tion in the engine electronics. Have the .,,.
19

Instruments and indicator lights
- For information on the audio/video and nav­
igation* functions, refer to the separate
MMI owner's manual.
Operation
The driver informotion system is operated using
the buttons on the multifunction steering wheel.
::ii
------ -,~
F ig. 6 Multifunction steering wheel: operating the dr iver
infor mation system
Fig. 7 Instrument cluster: opening the vehicle functions
menu
Operating
.,. Switch on the ignition.
.,. To switch between the tabs, press the rocker
switch @to the left or r ight
c:::> fig. 6.
.,. To access additional information below or
above, turn the thumbwheel@ down or up.
.,. To confirm a selection, press the thumbwheel
®·
Opening the Vehicle functions
.,. Se lect the first tab with the rocker switch@.
.,. Press the
l== I button. The Vehicle functions
menu is displayed c:::> fig. 7.
.,. To se lect a menu item, turn and press the
thumbwheel @.
24
~
Resetting values to zero
.,. In the Vehicle functions menu, select On­
board computer
or Efficien cy program .
.,. You can now select between the long-term
memory and short-term memory .
.,. To reset the values in a memory, press and hold
the thumbwheel @for one second.
The last function selected displays when you
switch the ignition on.
@ Tips
Disconnecting the battery causes all the
memory data to be erased.
On-board computer
Fig. 8 Instrument cluster: fuel consumption display
You can call up the following informat ion in the
on-boa rd computer:
- Date
- Dr iving t ime from the short-term memory
- Average consumption from the short-term
memory
- Average speed from the short-term memory
- Distance driven from the short-term memory
- Current fuel consumption
- Short-term memory overview
- Long-te rm memory
overv iew
The short-term memory collects driving informa­
tion from the time the ignition is switched on un­
ti l it is switched off. If you continue driving with­
i n two hours after switching the ignition off, the
new values are included when calculating the cur-
rent trip information.
II>

Instruments and indicator lights
@ Tips
-If the data are deleted in the effic iency pro­
gram, those va lues are also reset in trip
computer.
- Once you have turned a fue l economy mes­
sage off, it will only appear again after you
turn the ign ition on again.
- The fuel economy messages are not dis­
played in every instance, but rather in inter­
vals over a period of time.
Odometer
F ig . 11 Instrument cluste r Odometer and reset button
The odometer shows you how many miles (kilo­
meters) you have driven. You can switch the dis­
play from miles to kilometers and vice versa via
the MMI.
Upper odometer
The trip odometer shows the distance driven
since it was last reset. It can be used to measure
short distances. The last dig it indicates 1/10 of a
mile (100 meters) .
You can reset the trip odometer to zero by press­
ing the Reset button~-
Lower odometer
The lower odometer shows the total numbe r of
miles (kilometers) driven.
Malfunction message
If there is a malfunct ion in the instrument clus­
ter,
DEF w ill appear in the trip odometer display
area . Contact you r a uth orized Aud i dea ler to have
the prob lem corrected .
26
Time and date display
Fig. 12 Center conso le: a nalog clock
The date and time are shown in the instrument
cluster display ¢
page 23, fig. 4. There is also an
analog clock in the center console <=:>
fig. 12.
When you open the driver's door, the date and
time appear in the instrument cluster display for
30 seconds . When the ign ition is switched on,
the time is always displayed in the status line©
regardless of the current disp lay.
You can set the time on both clocks and the date display in the MMI. Refer to the MMI owner's
manual for instructions .
Service interval display
The service interval display reminds you when
your next service is due .
Fig. 13 Instrument cluster : Service interva l display
The service interval display works in two stages:
-Inspection or oil change reminder: After a
specified number of miles, a message appears
in the instrument cluster display when switch­
ing the ignition on or off¢
fig. 13 . The remain-
ing distance or t ime is displayed briefly.
II>

Removing the mechanical key
Fig. 19 R emote control master key: removing the mechani·
ca l key
• Press the release button @¢fig. 19.
• Pull the mechanical key @ out of the master
key.
Using the mechan ica l key, you can:
- lock and unlock* the storage compartment on
the passenger's side¢
page 73.
- lock and unlock the vehicle manually
¢page 35.
-lock the front and rear passenger doors me­
chanically¢
page 36.
-unlock the luggage compartment lid manually
¢page 39.
Check light and battery in the master key
Fig. 20 Remote master key: Remov ing the battery holder
Check light in the ma ste r key
The check light®¢ fig. 20 in the master key
provides information about different conditions.
• The check light turns on briefly once when a
button is pressed, and during an "inquiry" by
the conven ience key system.
Open ing and closing
• If the check light does not come on, the battery
is dead and has to be replaced. In addition,
when the battery is dead the
!I ind icator light
appears in the instrument cluster display as
well as the message
Please change the key
battery .
Ma ster key battery replacement
• Remove the mechanical key ¢page 31.
• Press the re lease button @¢ fig. 20 on the
battery holder and at the same time pull the
battery holder out of the master key in the di­
rection of the arrow .
.. Install the new batte ry CR 2032 with the"+"
sign facing down.
.. Push the battery holder carefully into the mas­
ter key .
.. Insta ll the mechanical key .
@ For the sake of the environment
Dispose of dead batteries properly so as not
to pol lute the environment.
(D Tips
The replacement battery must be the same
specification as the original.
Electronic immobilizer
The immobilizer helps to prevent unauthorized
use of your vehicle.
A computer ch ip inside your key automatically
deact ivates the electronic immob ilizer when the
key is inside the vehicle. When you remove the
key from the vehicle, the elect ronic immob ilizer
is automatically activated once again .
& WARNING
-
Always take the key with you when you leave
the vehicle. The key can disarm the electronic
engine immobilizer and permit an unauthor­
i zed person to start the engine and enable op­
eration of the vehicle systems such as power
window or power sunroof leading to serious
personal injury.
31

-The buttons for the power sun shades * in the
side windows.
- The button for the front passenger's seat ad­
justment*.
A WARNING 1=
- Always take the vehicle key with you when
leaving the vehicle, even for a short period
of time. This applies particularly when chil­
dren rema in in the vehicle . Otherwise the
children could start the engine or operate
electrical equipment such as power win­
dows. The power windows a re functional un­
ti l the driver's door or passenge r's door has
been opened.
- Pay ca reful attention when closing the win­
dows.
It could cause injury by pinching.
- When locking the veh icle from outside, the
vehicle must be unoccupied since the win­ dows can no longer be opened in an emer­
gency.
@ Tips
- Using the switches © and @, the driver can
also operate the power sunshades* in the
side windows.
- After tu rning the ignition off you can st ill
open and close the w indows for app roxi ­
ma tely 10 minutes. The powe r windows are
not switched off until the driver's door or
passenger's door has been opened.
What to do after a malfunction
-
The one -touch open and close function must be
reactivated if the battery has been disconnected .
.,. Pull and hold the power w indow switch unt il
the window is fully closed.
.,. Release the switch and then pull it again for at
least one second.
Openin g an d clos ing
Valet parking
The valet parking feature protects the luggage
compartment from unauthorized access.
Fig. 36 Valet parking button
With "valet parking" act ivated, the luggage com­
partment lid cannot be opened .
.,. Remove the mechanical key
c::> page 31.
.,. Open the glove compartment and activate
c::> fig. 36 the "valet parking" feature by press­
ing the
!VA LE T I button. The indicator light in
the switch illumina tes.
.,. Close the glove compartment and lock it with
the mechanical key.
.,. Leave the master key with the service personnel
for parking and keep the mechanical key with
you .
When the "valet parking" feature is activated:
- the unlocking button fo r the luggage compart­
ment lid~ in the driver's door is inactive
- the button~ on the master key is inactive
- the opening handle in the luggage compart-
ment lid is inactive.
The vehicle can be driven and locked and un­
locked with the master key . Access to the lug­
gage compartment is b locked.
When the valet parking function is switched on,
the message
V ale t p arki ng activat ed appears in
the instrument cluster d isp lay when you switch
the ignition on.
4 1