2016 AUDI A5 COUPE brake

Driving
oil pressure must first build up in the hy­
draulic valve adjusters. This is normal and not a cause for concern.
- If you leave the vehicle with the ignition
switched on, the ignition will switch off af­
ter a certain period of time. Please note that
electrical equipment such as exterior lights
will switch off as well when that happens .
Switching engine off
Applies to veh icles: w ith conven ience key
" Bring your vehicle to a complete stop .
" Automatic transmission: Move the selector lev­
er to the P or N position.
"Press the
I STA RT ENG INE S TOPI button
~ page 75, fig. 79.
Steering lock
The steering locks when you turn the engine off
using the
I START E NGINE STOP ! button and
open the driver's door. The locked steering helps
prevent vehicle theft.
Emergency off
If necessary, the engine can be switched off with
the selector lever in the R or D/S positions . The
engine stops if you press and hold the
I STAR T ENGIN E STOPI button at speeds below
6 mph (10 km/h) and press the brake pedal.
A WARNING
-Never turn off the engine before the vehicle
has come to a complete stop. The full func­
tion of the brake booster and the power
steering is not guaranteed. You must use
more force to turn or brake if necessary. Be­
cause you cannot steer and brake as you
usually would, this could lead to crashes
and serious injuries.
- For safety reasons, you should always park
your vehicle with the selector lever in P.
Otherwise, the vehicle could inadvertently
roll away .
- The radiator fan can continue to run for up
to 10 minutes even after you have turned
off the engine and removed the ignition key.
The radiator fan can also turn on again if the
76
engine coolant heats up because of intense
sunlight or heat build-up in the engine com­
partment.
- Always take the key with you whenever you
leave your vehicle . Otherwise, the engine
could be started or electrical equipment
such as the power windows could be operat ­
ed. This can lead to serious injury.
(D Note
If the engine has been under heavy load for
an extended period, heat builds up in the en­
gine compartment after the engine is switch ­
ed off - there is a risk of damaging the engine .
Allow the engine to run at idle for about two
minutes before switching it off.
Driver messages
Ignition is on
This message appears and a warning tone sounds
if you open the driver's door when the ignition is
switched on .
No key identified
This message appears when the
I STAR T ENGINE ST OP ! button is pressed if there
is no master key inside the vehicle or if the sys­
tem does not recogni ze it. For example, the mas­
ter key cannot be recognized if it is covered by an
object (e .g . aluminum brief case) which
screens
the radio signal. Electronic devices such as cell
phones can also interfere with the radio signal.
Press brake pedal to start engine
This message appears if you do not press the
brake pedal to start the engine in a vehicle with
an automatic transmission.
Press clutch pedal to start engine
This message appears if you do not press the
clutch pedal to start the engine in a vehicle with
a manual transmission.
Shift to N or P to start engine
This message appears when attempting to start
the engine if the selector lever for the automatic
transmission is not in the P or N position . The .,_

..... N
0 1-CX)
engine can only be star ted with the se lector in
these positions .
!I Is the key in the v ehicle?
This message appears if the master key is re­
moved from the vehicle with the engine run ning .
If the maste r key is no longer in the veh icle, you
cannot swi tch on the ignition after stopping the
engine and yo u also cannot start the engine
again. Moreover, you cannot lock the vehicle
from the outside with the key .
Shift to P otherwise vehicle can roll away . Door s
do not lo ck if l ever i s not in
P.
This message appears fo r safety reasons a long
with a warning signal. It appears if the selec to r
l eve r fo r th e automatic transmission is not in the
P posit ion when switching off the ignition . M ove
the selector leve r to the P position, otherwise the
ve hicle is not secured against rolling away. You
also cannot lock the vehicle using the locking button* on the door handle or using the remote
key.
Con venien ce key d efectiv e! Use ignition lo ck
This message appea rs if the engine mus t be
s t arted or stopped us ing t he igni tion key and no t
the
! START ENGINE STOPI button .
Electromechanical
parking brake
Operation
The electromechanical parking brake replaces
the hand brake.
Fig . 8 0 Center co nsole: Park ing b rake
rl
~ .. Pull on the switch@~ fig. 80 to apply the
~ parking brake. The ind icator lights in the sw itch ......
D rivi ng
and . (USA mode ls)/ . (Canada models) in
the instrument cluster illuminate.
.. W ith the ignition switc hed on, step on the
brake pedal or the accelerator pedal and press
the switch @ at the same time to release the
parking brake . The indicator lights in the switch
and . (USA models)/ . (Canada models) in
the instrument cluster go out .
Your vehicle is equipped with an electromechani­
cal park ing brake. The parking brake is designed
to prevent the vehicle from rolling un intent ional­
ly and replaces the ha nd b rake .
In add ition to the normal functions of a trad i­
t ional ha nd brake, the electromechanical parking
brake prov ides va rious conven ience and safety
funct ions.
When starting from rest
- The integral starting assist helps you when
driving by automatically releas ing the parking
brake ~
page 78 , Starting from rest.
- When start ing on inclines, the starting assist
prevents the veh icle from unintentionally roll­
ing back . T he brak ing force of the park ing brake
is not re leased unt il sufficient dr iving force has
been bu ilt up at the whee ls.
Emergency brake function
An emergency brake ensures that the veh icle can
be slowed down even if the
normal brakes fa il
~ page 79, Emergency braking .
A WARNING
If a gear or a drive range (automatic transmis­
s ion) is engaged wi th the vehicle stationa ry
a nd the engine runn ing, you must in no in­
stance acce lera te or release the clutch* care ­
l essly. Otherwise the vehicle wi ll sta rt to
move immediately- risk of an accident.
(1) Tips
- If the pa rk ing br ake is a pplied with the igni­
tion swi tche d off, the indicator lights i n the
switch and -(USA models) . (Cana­
da mode ls) in the instr ument cluster wi ll go
out after a certain period of time.
77

Driving
- Occasional noises when the parking brake is
applied and released are normal and are not
a cause for concern.
- When the vehicle is parked, the parking
brake goes through a self-test cycle at regu­
lar intervals. Any associated noises are nor­
mal.
Parking
.,. Press the brake pedal to stop the vehicle .
.,. Pull the switch @¢
page 77, fig. 80 to set the
parking brake .
.,. Automatic transmission: Move the selector lev-
er to P.
.. Turn the engine off¢.&, .
.. Manual transmission: Shift into 1st gear.
.. When on inclines or declines, turn the steering
wheel so that the vehicle will roll into the curb
if it begins to move.
A WARNING
-
-When you leave your vehicle -even if only
briefly -always remove the ignition key. This
applies particularly when children remain in
the vehicle. Otherwise the children could
start the engine, release the parking brake
or operate electrical equipment (e.g. power
windows). There is the risk of an accident.
- When the vehicle is locked, no one -particu­
larly not children should remain in the vehi­
cle. Locked doors make it more difficult for
emergency workers to get into the vehicle -
putting lives at risk.
Starting from rest
The starting assist function ensures that the
parking broke is released automatically upon
starting .
Stopping and applying parking brake
.. Pull the switch @¢ page 77, fig. 80 to apply
the parking brake.
78
Starting and automatically releasing the parking brake
.. When you start to drive as usual, the parking
brake is automatically released and your vehicle
begins to move.
When stopping at a traffic signal or stopping in city traffic on vehicles with an automatic trans­
mission, the parking brake can be applied. The
vehicle does not have to be held with the foot­ brake. The parking brake eliminates the tendency
to creep with a drive range engaged . As soon as
you drive off as usual, the parking brake is re­ leased automatically and the vehicle starts to
move .
Starting on slopes
When starting on inclines, the starting assist pre ­
vents the vehicle from unintentionally rolling back. The braking force of the parking brake is
not released until sufficient driving force has
been built up at the wheels.
(D Tips
For safety reasons, the parking brake is re­
leased automatically only when the driver's
safety belt is engaged in the buckle.
Starting off with a trailer
To prevent rolling back unintentionally on an in­
cline, do the following:
.. Keep the switch @¢ page 77, fig. 80 pulled
and depress the accelerator. The parking brake
stays applied and prevents the vehicle from
rolling backward.
.,. You can release the switch @once you are sure
that you are developing enough driving force at
the wheels by depressing the accelerator.
Depending on the weight of the rig (vehicle and
trailer) and the severity of the incline, you may
roll backwards as you start. You can prevent roll­
ing backwards by holding the parking brake
switch @pulled out and accelerating -just as
you would when starting on a hill with a conven­
tional hand brake .

Emergency braking
In the event that the conventional brake system
fails or locks.
11-In an emergency, pull the sw itch @c:> page 77,
fig. 80 and cont inue to pull it to slow your vehi­
cle down with the park ing brake .
11-As soon as you release the switch @ or acceler-
ate, the brak ing p rocess stops.
If you pull the sw itch @and hold it above a
speed of about
5 mph (8 km/h), the emergency
braking function is in itiated. The vehicle is braked
at all four wheels by activating the hydrau lic
b rake system. The brake performance is sim ila r
to making an eme rgency stop c:>
.&..
In order not to activate the emergency brak ing by
mistake, an audib le wa rning tone (buzze r)
sounds when the sw itch @ is pulled . As soon as
the switch @is re leased, or the acce lerator peda l
is depressed, emergency braking stops.
A WARNING
Emergency braking should only be used in an
emergency, when the normal foot brake has
failed or the brake pedal is obstructed. Using the parking brake to perform emergency
brak ing will slow your vehicle down as if you
had made a full bra ke appl ication . The laws of
physics cannot be suspended even with ESC
and its associated components (ABS, ASR, EDS). In corners and when road or weather
conditions a re bad, a f ull brake application
can ca use the vehicle to skid or the rear end to
break away- risking an accident.
Speed warning system
Overview
The speed warning sys tem helps you to keep your
driving speed below a set speed limit .
The speed warning system warns if the driver ex ­
ceeds a prev iously stored maximum speed. A
;::; warning tone w ill sound as soon as the vehicle
0 ~ speed exceeds the set speed by about 3 mph
~ (3 km/h). At the same time , a warning symbol Lil ,...., v:, ,....,
D riv ing
appea rs in the display. The symbo l's appearance
might be diff erent in some models.
T he speed warn ing system has two warning
thresholds that function independently of each
othe r and that have somewhat different p urpos­
es:
Speed warning 1
You can use speed warning 1 to set the max imum
speed w hile you are dr iving . T his sett ing will re ­
main in effect until you tu rn off the ignit ion, as­
sum ing that you have not changed o r reset the
setting .
T he . (USA models) /. (Canada models)
speed wa rning symbo l in the warning 1 disp lay
appears when you exceed the maximum speed .
It
goes out when the speed falls below the stored
maximum speed.
T he speed warn ing symbol will also go out if the
speed
exceeds the stored maximum speed by
more than about 2S mph
(40 km/h) for at least
10 seconds. The stored maximum speed is delet­
ed.
Sp eed wa rning 2
Storing warning 2 is recommended if you always
want to be reminded of a certain speed, for ex­
amp le wh en you are trav eling in a country that
has a genera l maximum speed limit, or if you do
not want to exceed a specified speed for winter
t ires .
T he . (USA models) /. (Canada mod els)
speed warning 2 symbol appears in the display
when you exceed the stored speed limi t. Unlike
warning 1 , it wilt not go out unt il the vehicle
speed drops below the stored speed limit .
Setting speed warning 2 c:>
page 80.
{D Tips
Even though your vehicle is eq uipped with a
speed warning system, you should still watch
the speedometer to make sure you are not
driving faster than the speed lim it.
79

Driving
Speed warning 1: setting a speed limit
Warning threshold 1 is set by the I SET I button .
Fig. 81 SET button in the instrum en t cluster
Storing the m aximum spe ed
• Drive at the desired maximum speed.
• Press the
!SE TI but ton in the instrumen t panel
display ~
fig. 81 for 1 second .
Resetting the maximum speed
• Drive the vehicle at a speed of at least 3 mph
(5 km/h)
• Press the
~IS-E T~I button for more than 2 seconds .
The . (USA models)
I. (Canada models)
speed warn ing symbol will appear briefly in the
d isp lay when yo u release the
!SE TI button to indi­
ca te that the max imum speed has been stored
successfully .
The max imum speed remains stored until it is
changed by pressing the
I SETI button again brief­
ly or unt il it is deleted by a lengthy p ush on the
button.
Speed warning 2: setting a speed limit
The radio or MMI* control unit is used to set,
change or delete warning threshold
2 .
• Se lect : !CARI funct ion button> Instrum ent
clu ster > Speed warning .
Or
• Select : !CARI function button> C ar sys te m s*
contro l button > Dri ver ass is t > S peed warnin g.
Wa rning threshold 2 can be set in the speed
range star ting from 20 mph
to 150 mph (30 km/
h to 240 km/h) . Set tings can each be ad justed in
intervals of 5 mph (10 km/h).
80
Cruise control system
Switching on
The cruise control system makes it possible to
drive at a constant speed starting at
20 mph (30
km/h) .
0
f
®l
0
Fig. 82 Co ntro l lever w it h push -bu tton
Fig . 83 D isp lay : Selected speed
g M 0 ±
~
Q)
~ ci: Q) m
• Pull the lever to position (D c:> fig . 82 to switch
the system on.
• Drive at the speed to be controlled.
• Press button @to set that speed .
The stored speed and the green symbol
[lj;(IJM4 (US model)/ El (Canadian model) are
shown in the d isplay
c:> fig. 83. The d isplay may
vary, depending on the type of display in your ve­
hicle .
The speed is kept constant by modifying engine power or through an active brake intervention.
A WARNING
- Always pay attention to the traffic around
you when the cruise control is in operation .
You are always respons ible for your speed
and the distance between your veh icle and
other veh icles .
-

.... N
0 I­co .... OJ:> Lil
.... OJ:> ....
-For reasons of safety, cruise control should
not be used in the city, in stop-and-go traf­
fic, on twisting roads and when road condi­
t ions are poor (such as ice, fog, gravel,
heavy ra in and hydroplan ing) -risk of acci­
dent .
- Turn
off the cruise control temporar ily when
enter ing turn lanes, h ighway exit lanes o r in
construction zones.
- Please note that inadvertently "rest ing"
your foot on the accelerator pedal causes
the cruise control not to brake. This is be­
cause the cruise cont rol is overridden by the
dr iver's acceleration.
- If a brake system ma lf u nction such as over­
heating occu rs when the c ruise contro l sys­
tem is switched on, the braking function in
the system may be switched
off . The other
cruise contro l functions remain active as
long as the indicator light
[lj;(i )~i~ (US mod­
els)/ .. (Canadian models) is on .
(D Tips
-Vehicles with manual transmission: You can
attain the set speed only if the gear that is
currently engaged will allow it, or if it does
not tax the engine and allows it to run
smooth ly. Therefore sh ift into a higher or
lower gear in a timely ma nner.
- The brake lights illuminate as soon as the
brakes apply automatically .
Changing speed
.,. To inc rease/decrease the speed in increments,
tap the lever in the
0 10 direction ¢ page 80,
fig. 82.
.,. To inc rease/decrease the speed qu ickly , ho ld
the leve r in the
0 10 direction until the de­
si red speed is displayed .
You can a lso press the accelerator pedal down to
increase yo ur speed, e.g. if you want to pass
someone . The speed you saved earlier wi ll re ­
sume as soon as you let
off of the acce lerator
pedal.
I f, however, you exceed your saved speed by
6 mph
( 1 0 km/h) for longer than 5 minutes, the
D riv ing
cruise contro l wi ll be turned off temporarily. The
green symbol in the display turns white. The
saved speed remains t he same.
Presetting your speed
You can preset your desired speed while the vehi­
cle is not moving.
.,. Switch on the ign ition.
.,. Pull lever into position
(D ¢ page 80, fig . 82 .
.,. Press the lever in the 0 or 0 direction to in-
crease or decrease your speed.
.,. Release the lever to save that speed.
This function makes it possible, for example, to save the speed you want before driving on the
highway . Once on the highway, activate the
cruise contro l by pull ing the lever toward
(D .
Switching off
Temporar y de acti vation
.,. Press the brake pedal, or
.,. Manual transmission: Keep the clutch pedal
pressed down
longer, or
.,. Press the lever into position @ (not clicked into
place)
~ page 80, fig. 82, o r
.,. Dr ive fo r longer than 5 mi nutes a t more than
6 mph (1 0 km/h) above the s to red speed.
Switching off completely
.,. Press lever into pos it ion @ (clicked into p lace),
or
.,. Switch the ignit ion
off .
T he speed you saved will be retained if the cruise
control has been switched off temporarily . To re­
s u me the saved speed , let up on the bra ke or
cl utch pedal and pull the lever to position
(D .
Switch ing the ignition off erases the saved speed .
A WARNING
--
You should only return to the saved speed if it
i s not too fast for the current t raffic condi ­
tions -ris k of an accident!
81

,-1 N
0 1-CX)
rl I.Cl U"I
,-1 I.Cl ......
Selector lever positions
Applies to vehicles: with S tronic/t iptron ic
F ig. 85 Display in the instrument cluste r: selector leve r in
pos it ion P
The selector Lever position engaged appears next
to the selector Lever as well as in the instrument
cluster display.
P -Pa rk
In th is selector lever pos ition the t ransm iss ion is
mechanically locked . Engage P only when the ve­
hi cle is
completely stopped¢&. in Driving the
automatic transmission on page 85.
To shift in o r out of position P, you must first
press and ho ld the brake pedal and then p ress
the re lease button in the selector lever handle
while moving the se lector lever to or from P. You
can shift out of this position only with the igni­
tion on .
R - Rever se
Select R only when the vehicle is at a full stop
and the engine is r unning at idle speed ¢&. in
Driving the automatic transmission on
page 85.
Before you move the selector Lever to R, press
both the release button in the hand le of these­
lector lever
and the brake pedal at the same
time .
When the ignit ion is on, the backup l ights illumi­
nate when the se lecto r lever is moved into R .
N · N eutral
The transmission is in neutral in this posit ion .
Shift to this position for standing w ith the brakes
appl ied ¢&.
in Driving the automatic transmis­
sion on page 85.
Aut oma tic tr ansm iss ion
When the vehicle is stationary or at speeds be low
1 mph (2 km/h), you must a lways apply the foot­
brake before and wh ile moving the Lever out of N .
D/S · Normal position fo r driving fo rward
In the D/S pos ition, the transmission can be op­
erated eithe r in the normal mode Dor in the
sport mode S. To select the sport mode S, pull
the se lector lever back briefly. Pulling the lever
back again will select the normal mode D. The in­
strument cluster display shows the selected driv­
ing mode.
In the
norm al mode D, the transmission auto­
matically selects the suitable gear ratio . It de ­
pends on engine Load, vehicle speed and driving
style.
Se lect the
sport mode S for sporty driving . The
vehicle makes full use of the engine's power .
Shift ing may become noticeable when accelerat­
ing .
When the vehicle is stat ionary or at speeds be low
1 mph (2 km/h), you must a lways apply the foot
brake before and while moving the Lever to D/S
out of N.
_& WARNING
-
Read and follow all WARNINGS¢&. in Driv­
ing the automatic transmission on
page 85 .
(D Note
Coasting downhill with the transmission in N
and the engine not running w ill result in dam­
age to the automatic transm iss ion and possi­
bly the cata lytic conve rter.
¢j) Tips
- On vehicles with dr ive select*, you can ad­
just the sporty shift cha racteristics in the
Dynamic driving mode. Swill appear in the
ins trument clus ter display instead of D.
- If you acc identally select N wh ile driving,
take your foot off the accelerator pedal im­
media tely and wai t for the eng ine to s low
dow n to id le befo re sele cting D/S.
83

Automatic transmission
-If there is a power fa ilure, the selec to r l ever
will not move out of the P pos it ion . The
emergency release can be used if this hap­
pens
¢ page 88.
Automatic Shift Lock (ASL)
App lies to veh icles: with 5 tro nic/tiptron ic
The Automatic Shift Lock safeguards you against
accidentally shi~ing into a forward or the re­
verse gear and causing the vehicle to move unin­ tentionally.
"' 0 ~ N ~ 00 a,
Fig. 86 Shi ft ga te: se lector lever lock pos it io n s a nd r elease
butto n highlig hted
The se lector lever lock is released as fo llows :
.. Turn the ign ition on.
.. Step on t he b rake pedal.
At the same time
press and hold the release b utton on the side of
the gea r selector knob
c:> fig . 86 with you r
th umb until you have moved the se lector lever
to the desired position .
Automatic selector lever lock
The se lector lever is locked in t he P an d N posi­
tions when the ignition is turned on. You must
press the brake pedal and t he release b utt on to
select a nothe r pos ition . As a re min der to the
d river, the follow ing wa rning ap pears in t he in­
s trumen t cluster display when th e selec tor is in P
a nd N:
When stationary apply brake pedal while select­
ing gear
The A utomat ic Shift Lock only functions when the
ve hicle is stationary or at speeds below 1 mph
(2 km/ h).
84
At spee ds above abou t 1 mp h (2 k m/h) the A uto ­
matic Shift Lock is automatically deact ivated in
the N pos ition .
A time de lay e lemen t prevents the se lec tor lever
from lo cking when i t is move d thro ugh the N po ­
sition (going from R to D/S) . T he locking eleme nt
will lock the selector leve r if the lever is le ft in N
(Ne utral) for mo re t han approximately 2 sec­
onds, without the b rake peda l bei ng p ressed .
Release button
The re lease but ton o n the selec tor lever p revents
t h e leve r from be ing accidenta lly shifted into cer­
ta in positions . Depending on the direction of the
shift, the selector lever locks at diffe rent pos i­
tions. The positions are highlig hted in the illus­
tra tion
c::> fig . 86.
Ignition key safety interlock
The key ca nnot be removed from the i gnition un­
l ess the se lector lever is in the P park position.
When the ignition key is removed, the selector
l ever w ill be locked in the P posit ion.
Driving the automatic transmission
Applies to vehicles: with S tronic/tiptronic
Fig. 87 Shift gate o n th e ce nter conso le : se lector lever w ith
r elease butto n
Starting the engine
.. The se lecto r lever m ust be in P or N .
Starting off
.. Press an d hold the brake peda l.
.. Press and hold the release button in the se lec­
tor lever hand le, select the desired se lector lev-
er position s uc h as D/S and releas e the b utton . .,.