,....,
N
0
""' CX) ,....,
I.Cl U"I ,....,
I.Cl ,....,
.. Align the vehicle jack so the jaw@ covers the
notch and the base plate @ is flat on the floor.
The base plate @ must be
vertical under the
lift ing point @.
.. Install the rod on the vehicle jack : Insert the
rod into the opening on the handwheel. Turn
t h e rod left or right to secure it .
.. Cont inue raising the jack with the rod until the
wheel lifts off the ground slightly .
Position the vehicle jack
only under the designat
ed lifting points on the sill~
fig. 201. There is ex
actly
one locat ion for each wheel. The jack m ust
n ot be positioned at any other location~ &~© -
Soft gro und under the jack can cause the veh icle
to slip off the jack. Always place the jack on firm
g round . U se a flat, stable support if necessary .
Use a non-slip surface such as a r ubber mat on a
slippery surfa ce such as tile.
& WARNING
- Yo u or your passengers could be injured
whi le changing a wheel if you do not follow
these safety precautions:
- Position the veh icle jack only at the desig
nated lifting points and align the jack .
Othe rw ise, the vehicle jac k cou ld slip and
cause an injury if it does no t have suffi
cient hold on the vehicle .
- A soft or uns table s urface unde r the jack
may c ause the vehicle to slip off the jac k.
Always p rovide a firm base for the jack on
the ground . If necessary, use a sturdy
board under the jack .
- O n ha rd, slippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipping.
- To help prevent injury to yourself and yo ur
passengers:
- Do not ra ise the vehicle unt il you are sure
the jack is securely engaged.
- Passengers must not remain in the vehicle when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traff ic.
Em ergen cy a ssis tanc e
-Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack.
(D Note
Do not lift the vehicle by the si ll. Pos ition the
vehicle jack on ly at the designated lifting
po ints on the sill. Otherwise, your veh icle w ill
be damaged.
Taking the wheel off /installing the spare
tire
Follow these instructions step-by-step for chang
ing the wheel.
F ig . 203 Chang ing a w hee l: us ing the screwdriver handle
(with the blade removed) to turn th e bolts
Fi g. 20 4 Cha ngin g a w heel: alignme nt pin ins ide the top
h ole
After yo u have loosened all wheel bolts and
raised the vehicle off the ground, remove and re
place the wheel as follows:
Removing the wheel
.. Remove the topmost wheel bo lt completely
w ith the
hexagon al so cket in t he sc rewdrive r
handle (ve hicl e too l kit) ~
fig. 203 and set it
aside on a
clean surface.
243
Emergency situations
Raising the vehicle
Lifting with workshop hoist and with floor
jack
Th e vehicle may only b e lift ed at the lifting
poin ts illust rated.
F ig .. 216 F ro nt lift ing po int
F ig. 217 Rea r lifti ng po int
.,. Read and heed WARNING ¢ A-
.,. Locate lifti ng po ints ¢ fig. 216 and ¢ fig. 217 .
.,. Adjust lifting arms of wo rkshop hoist or floor
jack to match veh icle lifting points .
.,. In se rt a rubb er pad between t he floor jack/
wor kshop hoist a nd the lif ting poin ts .
If you must lift your vehicle with a floor jack to
work underneath, be sure the vehicle is safely
supported on stands intended for this purpose .
Front lifting point
The lift ing po int is located on the floo r pan re in
forcement about at the same leve l as the jack
mo unt ing point ¢
fig. 216 . Do not lift the vehi
cle at the vertical sill rei nforcement.
Rear lifting point
The lift ing po int is located on the vertica l re in
for cement of the lower sill fo r the on board jack
¢fig. 217.
254
Lifting with vehicle jack
Refer to ~ page 242.
A WARNING
-To re duce the r is k of serious injury and vehi
cle dama ge .
- Always lift the vehicle o nly at the special
workshop hois t an d floor jack lift points il
l ustrat ed
~ fig. 216 and ~ fig . 217.
- Failur e to lift the v ehicle at these points
could ca use the veh icle to tilt or fall from
a lift if the re is a cha ng e i n ve hicle weigh t
dis tribu tion and ba lan ce . T his mig ht hap
p en, for exa mple, whe n he avy co mpo
n en ts such as the engine block o r tr an s
mission are removed.
- W hen re m ov in g h eavy co mponen ts like
these, an cho r veh icle to hoist or ad d co rre
spond ing weights to ma inta in the ce nter of
gravity . Othe rw ise, the vehicle mi ght t ilt o r
slip off t he hoist, causing serious pe rsonal
in jur y.
(D Note
- Be aware of the fo llowing po ints befo re lift
ing the vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil pan, the transmission housing, the front
or rear axle or the body side members .
This could lead to serious damage .
- To avoid damage to the underbody or
chassis frame, a rubber pad must be in
serted between the floor jack and the lift
points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity of
the hoist.
- Before driving over a workshop hoist , en
sure that there is sufficient clearance be
tween the hoist and low parts of the ve
h icle.
