2015 YAMAHA YZ450F clutch

CLUTCH......................................................................................................... 5-37
REMOVING THE CLUTCH ...................................................................... 5-40
CHECKING THE FRICTION PLATES...................................................... 5-40
CHECKING THE CLUTCH PLATES ........................................................ 5-40
CHECKING THE CLUTCH SPRINGS...................................................... 5-40
CHECKING THE CLUTCH HOUSING ..................................................... 5-41
CHECKING THE CLUTCH BOSS ............................................................ 5-41
CHECKING THE PRESSURE PLATE ..................................................... 5-41
CHECKING THE PUSH LEVER SHAFT .................................................. 5-41
CHECKING THE CLUTCH PUSH RODS ................................................ 5-41
CHECKING THE PRIMARY DRIVE GEAR .............................................. 5-41
CHECKING THE PRIMARY DRIVEN GEAR ........................................... 5-42
INSTALLING THE OIL SEAL................................................................... 5-42
INSTALLING THE RIGHT CRANKCASE COVER ................................... 5-42
INSTALLING THE CLUTCH ..................................................................... 5-42
INSTALLING THE KICKSTARTER LEVER ............................................. 5-45
KICKSTATER................................................................................................. 5-46
REMOVING THE KICK SHAFT ASSEMBLY ........................................... 5-47
CHECKING THE KICK SHAFT AND RATCHET WHEEL ........................ 5-47
CHECKING THE KICK GEAR, KICK IDLE GEAR
AND RATCHET WHEEL ......................................................................... 5-47
INSTALLING THE KICK SHAFT ASSEMBLY .......................................... 5-47
INSTALLING THE KICK IDLE GEAR ....................................................... 5-48
SHIFT SHAFT................................................................................................. 5-49
REMOVING THE SHIFT GUIDE AND SHIFT LEVER ASSEMBLY ......... 5-51
REMOVING THE SEGMENT ................................................................... 5-51
CHECKING THE SHIFT SHAFT .............................................................. 5-51
CHECKING THE SHIFT GUIDE AND SHIFT LEVER ASSEMBLY ......... 5-51
CHECKING THE STOPPER LEVER ....................................................... 5-51
INSTALLING THE STOPPER LEVER ..................................................... 5-52
INSTALLING THE SEGMENT.................................................................. 5-52
INSTALLING THE SHIFT GUIDE AND SHIFT LEVER ASSEMBLY ....... 5-52
INSTALLING THE SHIFT SHAFT ............................................................ 5-53
INSTALLING THE SHIFT PEDAL ............................................................ 5-53
OIL PUMP AND BALANCER GEAR............................................................. 5-54
REMOVING THE BALANCER ................................................................. 5-56
CHECKING THE PRIMARY DRIVE GEAR, BALANCER SHAFT
DRIVE GEAR, AND BALANCER WEIGHT GEAR .................................. 5-56
CHECKING THE BALANCER .................................................................. 5-56
CHECKING THE OIL PUMP .................................................................... 5-56
ASSEMBLING THE OIL PUMP ................................................................ 5-57
INSTALLING THE OIL PUMP AND BALANCER GEAR .......................... 5-57

ENGINE REMOVAL
5-4
Removing the engine
Order Part name Q’ty Remarks
Use a suitable stand to raise the front wheel
off the ground.
Seat Refer to “GENERAL CHASSIS” on page 4-1.
Side cover (left/right) Refer to “GENERAL CHASSIS” on page 4-1.
Air scoop (left / right) Refer to “GENERAL CHASSIS” on page 4-1.
Rear fender Refer to “GENERAL CHASSIS” on page 4-1.
Fuel tank Refer to “FUEL TANK” on page 7-1.
Exhaust pipe and silencer Refer to “ENGINE REMOVAL” on page 5-1.
Air filter case Refer to “THROTTLE BODY” on page 7-5.
Throttle body Refer to “THROTTLE BODY” on page 7-5.
Clutch cable Refer to “CLUTCH” on page 5-37.
Shift pedal Refer to “SHIFT SHAFT” on page 5-49.
1 Engine guard 1
2 Brake pedal 1
3Spring 1
4 Cylinder head breather hose 1
5 Drive sprocket cover 1
6 Drive chain guide 1
New
New
LS
M
8
8
7
6
11
45
New
1 10
3
2

CLUTCH
5-37
EAS1SL5233
CLUTCH
Removing the clutch
Order Part name Q’ty Remarks
Engine oilDrain.
Refer to “CHANGING THE ENGINE OIL” on
page 3-15.
Brake pedal Refer to “ENGINE REMOVAL” on page 5-1.
1 Clutch cable 1 Disconnect.
2 Clutch cover 1
3 O-ring 1
4 Clutch spring 6
5 Pressure plate 1
6 Push rod 1 1
7 Circlip 1
8Washers 1
9 Bearing 1
10 Ball 1
11 Push rod 2 1
12 Friction plate 1 5
13 Clutch plate 7
LS
New
New
New
2
3 45
78961011
13
12
12
18
1
14
13
13
17
16
15
T.R.
T.R.
T.R.
T.R.
LT

CLUTCH
5-38
14 Friction plate 2 3 Identification color (purple)
15 Clutch boss 1
16 Thrust washer 1
17 Primary driven gear 1
18 Push lever shaft 1
For installation, reverse the removal proce-
dure.
Removing the clutch
Order Part name Q’ty Remarks
LS
New
New
New
2
3 45
78961011
13
12
12
18
1
14
13
13
17
16
15
T.R.
T.R.
T.R.
T.R.
LT

CLUTCH
5-39
Removing the right crankcase cover
Order Part name Q’ty Remarks
Right engine guard Refer to “ENGINE REMOVAL” on page 5-1.
Engine oilDrain.
Refer to “CHANGING THE ENGINE OIL” on
page 3-15.
CoolantDrain.
Refer to “CHANGING THE COOLANT” on
page 3-8.
Brake pedal Refer to “ENGINE REMOVAL” on page 5-1.
Clutch cover Refer to “CLUTCH” on page 5-37.
1 Oil filter element cover 1
2 Oil filter element 1
3 Radiator pipe 2 1
4 Kickstarter lever 1
5 Right crankcase cover 1
6 Gaskets 1
7 Dowel pin 2
8Collar 1
For installation, reverse the removal proce-
dure.
T.R.
LS
New
New
67
2
5
4
1
7 8
New
3
LS
New
New
LS
LS
NewNew
LT
LS

CLUTCH
5-40
EAS1SL5234REMOVING THE CLUTCH
1. Remove:
• Clutch boss nut “1”
• Conical washer “2”
• Clutch boss “3”
TIP
While holding the clutch boss with the clutch
holder “4”, loosen the clutch boss nut.
EAS1SL5235CHECKING THE FRICTION PLATES
1. Check:
• Friction plate
Damage/wear  Replace the friction plates
as a set.
2. Measure:
• Friction plate thickness
Out of specification  Replace the friction
plates as a set.
TIP
Measure it at four points on the friction plate.
EAS1SL5236
CHECKING THE CLUTCH PLATES
1. Check:
• Clutch plate
Damage  Replace the clutch plates as a
set.
2. Measure:
• Clutch plate warpage
(with a surface plate and thickness gauge
“1”)
Out of specification  Replace the clutch
plates as a set.
EAS1SL5237CHECKING THE CLUTCH SPRINGS
1. Check:
• Clutch spring
Damage  Replace the clutch springs as a
set.
2. Measure:
• Clutch spring free length
Out of specification  Replace the clutch
springs as a set. Clutch holder
90890-04086
YM-91042
Friction plate thickness
2.92–3.08 mm (0.115–0.121 in)
Wear limit
2.85 mm (0.112 in)
34
12
Warpage limit
0.10 mm (0.0039 in)
Clutch spring free length
48.00 mm (1.89 in)
Minimum length
47.00 mm (1.85 in)

CLUTCH
5-41
EAS1SL5238CHECKING THE CLUTCH HOUSING
1. Check:
• Clutch housing dogs “a”
Damage/pitting/wear  Deburr the clutch
housing dogs or replace the clutch housing.
TIP
Pitting on the clutch housing dogs will cause er-
ratic clutch operation.
EAS1SL5239CHECKING THE CLUTCH BOSS
1. Check:
• Clutch boss splines
Damage/pitting/wear  Replace the clutch
boss.
TIP
Pitting on the clutch boss splines will cause er-
ratic clutch operation.
EAS1SL5240CHECKING THE PRESSURE PLATE
1. Check:
• Pressure plate
Crack/damage  Replace.
EAS1SL5241
CHECKING THE PUSH LEVER SHAFT
1. Check:
• Push lever shaft
Wear/damage  Replace.
EAS1SL5242CHECKING THE CLUTCH PUSH RODS
1. Check:
• Push rod 1 “1”
• Bearing “2”
• Washer “3”
• Push rod 2 “4”
•Ball “5”
Cracks/damage/wear  Replace.
2. Measure:
• Push rod 2 bending limit
Out of specification  Replace.
EAS1SL5243CHECKING THE PRIMARY DRIVE GEAR
1. Check:
• Primary drive gear
Damage/wear  Replace the primary drive
and primary driven gears as a set.
Excessive noise during operation  Re-
place the primary drive and primary driven
gears as a set.
2. Check:
• Primary-drive-gear-to-primary-driven-gear
free play
Free play exists  Replace the primary
drive and primary driven gears as a set.
a
Push rod bending limit
0.10 mm (0.0039 in)

CLUTCH
5-42
EAS1SL5244CHECKING THE PRIMARY DRIVEN GEAR
1. Check:
• Primary driven gear
Damage/wear  Replace the primary drive
and primary driven gears as a set.
Excessive noise during operation  Re-
place the primary drive and primary driven
gears as a set.
EAS1SL5245INSTALLING THE OIL SEAL
1. Install:
• Oil seal “1”
• Washer “2”
• Circlip “3”
TIP
• Apply is lithium-soap-based grease on the oil
seal lip.
• Install the oil seal in parallel with its manufac-
ture's marks or numbers facing inward.
EAS1SL5246INSTALLING THE RIGHT CRANKCASE
COVER
1. Install:
• Dowel pin “1”
• O-rings “2”
• Collar “3”
• Gasket “4”
TIP
Apply the lithium-soap-based grease on the O-
ring.2. Install:
• Right crankcase cover “1”
• Right crankcase cover bolt “2”
TIP
• Apply the engine oil on the impeller shaft end.
• When installing the crankcase cover onto the
crankcase, make sure that the impeller shaft
end “3” aligns with the balancer end slot “4”.
• Tighten the right crankcase cover bolts in
stages and in a crisscross pattern.
EAS1SL5247INSTALLING THE CLUTCH
1. Install:
• Push lever shaft “1”
TIP
• Apply the lithium soap base grease on the oil
seal lip.
• Before installation, apply the engine oil to the
push lever shaft sliding surface.
New
New
3
2
1
LS
New
New
1
1 4
2
New
New
3
LS
Right crankcase cover bolt
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
T R..
12
1