2015 YAMAHA VMAX radiator cap

DESCRIPTION
2-2
2
EAU10421
Right view
12 4 6
7
5
3
9
11
8
10
1. Passenger seat (page 3-25)
2. Rear brake fluid reservoir (page 6-25)
3. Luggage strap holder (page 3-31)
4. Rider seat (page 3-25)
5. Fuse box 1 (page 6-34)
6. Radiator cap (page 6-16)
7. Coolant reservoir (page 6-16)
8. Engine oil level check window (page 6-11) 9. Brake pedal (page 3-20)
10.Fuse box 2 (page 6-34)
11.Shock absorber assembly compression damping force adjusting
knob (page 3-29)U2CEE0E0.book Page 2 Wednesday, August 27, 2014 11:11 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-17
63. If the coolant is at or below theminimum level mark, remove the
coolant reservoir cap guard by re-
moving the bolt, and then remove
the reservoir cap. WARNING! Re-
move only the coolant reservoir
cap. Never attempt to remove
the ra diator cap when the en-
g ine is hot.
[EWA15162]
4. Add coolant to the maximum level
mark, and then install the reservoir
cap. NOTICE: If coolant is not
availa ble, use distille d water or
soft tap water instea d. Do not use har
d water or salt water
since it is harmful to the en gine.
If water has been used instead
of coolant, replace it with cool-
ant as soon as possi ble, other-
wise the coolin g system will not
b e protecte d a gainst frost an d
corrosion. If water has been
a dde d to the coolant, have a
Yamaha dealer check the anti-
freeze content of the coolant as
soon as possi ble, otherwise the
effectiveness of the coolant will
b e re duce d.
[ECA10473]
5. Install the coolant reservoir cap
guard by installing the bolt.
EAU46426
To chan ge the coolant
1. Place the vehicle on a level sur- face and let the engine cool if nec-
essary.
2. Remove cowling A. (See page 6-8.) 3. Remove the right air intake duct
by removing the bolts.
4. Place a container under the en- gine to collect the used coolant.
5. Remove the radiator cap. WARNING! Never attempt to re-
move the ra diator cap when the
en gine is hot.
[EWA10382]
1. Coolant reservoir cap
2. Coolant reservoir cap guard
3. Bolt
4. Maximum level mark
5. Minimum level mark
2
1
5
4
3
Coolant reservoir capacity (up to
the maximum level mark):
0.27 L (0.29 US qt, 0.24 Imp.qt)
1. Bolt
2. Right air intake duct
1 1
2
U2CEE0E0.book Page 17 Wednesday, August 27, 2014 11:11 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-18
6
6. Remove the coolant reservoir cov-
er and coolant reservoir by remov-
ing the bolts. 7. Remove the coolant reservoir cap
guard by removing the bolt, and
then remove the reservoir cap.
8. Drain the coolant from the coolant reservoir by turning it upside
down.
9. Install the coolant reservoir cover and the coolant reservoir by plac-
ing them in their original position,
and then installing the bolts.
10. Remove the coolant drain screw and its O-ring to drain the cooling
system. 11. After the coolant is completely
drained, thoroughly flush the cool-
ing system with clean tap water.
12. Install the coolant drain screw and its new O-ring.
13. Hold the vehicle upright, and pour the specified amount of the rec-
ommended coolant into the radia-
tor and reservoir. NOTICE: Failing
to hol d the vehicle upri ght when
fillin g the ra diator with coolant
may cause air to be trappe d in
the coolin g system.
[ECA16541]
1. Radiator cap
1. Bolt
2. Coolant reservoir cover
3. Coolant reservoir
1
2
3
1
1. Bolt
2. Coolant reservoir cap
3. Coolant reservoir cap guard
2
3
1
1. Coolant drain screw
2. O-ring
1
2
U2CEE0E0.book Page 18 Wednesday, August 27, 2014 11:11 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-19
614. Install the coolant reservoir cap,
and then install the reservoir cap
guard by installing the bolt.
15. Install the radiator cap.
16. Start the engine, let it idle for sev- eral minutes, and then turn it off.
17. Remove the radiator cap to check the coolant level in the radiator. If
necessary, add sufficient coolant
until it reaches the top of the radi-
ator, and then install the radiator
cap.
18. Check the coolant level in the res- ervoir. If necessary, remove the
coolant reservoir cap guard and the cap, add coolant to the maxi-
mum level mark, and then install
the cap and the cap guard.
19. Start the engine, and then check the vehicle for coolant leakage. If
coolant is leaking, have a Yamaha
dealer check the cooling system.
20. Install the right air intake duct by installing the bolts.
21. Install the cowling.
EAU36765
Air filter elementThe air filter element must be replaced
at the intervals specified in the periodic
maintenance and lubrication chart.
Have a Yamaha dealer replace the air
filter element.
Antifreeze/water mixture ratio: 1:1
Recommen ded antifreeze:
High-quality ethylene glycol anti-
freeze containing corrosion inhibi-
tors for aluminum engines
Coolant quantity:
Radiator (including all routes):3.75 L (3.96 US qt, 3.30 Imp.qt)
Coolant reservoir (up to the maxi-
mum level mark): 0.27 L (0.29 US qt, 0.24 Imp.qt)
U2CEE0E0.book Page 19 Wednesday, August 27, 2014 11:11 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-43
6En
gine overheatin g
WARNING
EWAT1041
Do not remove the ra diator cap when the en gine an d ra diator are hot. Scal din g hot flui d an d steam may be
b lown out un der pressure, which coul d cause serious injury. Be sure to wait until the en gine has coole d.
 Place a thick ra g, like a towel, over the ra diator cap, an d then slowly rotate the cap counterclockwise to the
d etent to allow any resi dual pressure to escape. When the hissin g soun d has stoppe d, press d own on the cap
while turnin g it counterclockwise, an d then remove the cap.TIPIf coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended cool-
ant as soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
U2CEE0E0.book Page 43 Wednesday, August 27, 2014 11:11 AM

SPECIFICATIONS
8-1
8
Dimensions:Overall length:2395 mm (94.3 in)
Overall width:
820 mm (32.3 in)
Overall height: 1190 mm (46.9 in)
Seat height: 775 mm (30.5 in)
Wheelbase:
1700 mm (66.9 in)
Ground clearance: 140 mm (5.51 in)
Minimum turning radius: 3500 mm (137.8 in)Wei ght:Curb weight:
310 kg (683 lb)Engine:Engine type:
Liquid cooled 4-stroke, DOHC
Cylinder arrangement: V-type 4-cylinder
Displacement: 1679 cm³
Bore × stroke:
90.0 × 66.0 mm (3.54 × 2.60 in)
Compression ratio: 11.3 : 1
Starting system: Electric starter
Lubrication system:
Wet sump
Engine oil:Recommended brand:
YAMALUBE
Type:
SAE 10W-30, 10W-40, 10W-50, 15W-40,
20W-40 or 20W-50
Recommended engine oil grade: API service SG type or higher, JASO
standard MA
Engine oil quantity:
Without oil filter cartridge replacement: 4.30 L (4.55 US qt, 3.78 Imp.qt)
With oil filter cartridge replacement:
4.70 L (4.97 US qt, 4.14 Imp.qt)Final gear oil:Type:
Yamaha genuine shaft drive gear oil SAE
80W-90 API GL-5
Quantity: 0.30 L (0.32 US qt, 0.26 Imp.qt)
Coolant quantity:Coolant reservoir (up to the maximum level
mark):0.27 L (0.29 US qt, 0.24 Imp.qt)
Radiator (including all routes): 3.75 L (3.96 US qt, 3.30 Imp.qt)Air filter:Air filter element:Oil-coated paper elementFuel:Recommended fuel:
Premium unleaded gasoline (Gasohol (E10)
acceptable)
Fuel tank capacity:
15.0 L (3.96 US gal, 3.30 Imp.gal)
Fuel reserve amount: 3.9 L (1.03 US gal, 0.86 Imp.gal)Fuel injection:Throttle body:
ID mark: 2S31 00Spark plu g(s):Manufacturer/model:
NGK/CR9EIA
Manufacturer/model: DENSO/IU27D
Spark plug gap:
0.8–0.9 mm (0.031–0.035 in)Clutch:Clutch type:Wet, multiple-discTransmission:Primary reduction ratio:1.509 (86/57)
–20 –10 0 1020 30 40 50 C
10 30 50 70 90 110
0 130 F
SAE 10W-30
SAE 15W-40SAE 20W-40SAE 20W-50
SAE 10W-40SAE 10W-50
U2CEE0E0.book Page 1 Wednesday, August 27, 2014 11:11 AM

SPECIFICATIONS
8-3
8
Wheel travel:110 mm (4.3 in)Electrical system:Ignition system:
TCI
Charging system: AC magnetoBattery:Model:
YTZ14S
Voltage, capacity: 12 V, 11.2 AhHea dlig ht:Bulb type:
Halogen bulbBul b volta ge, watta ge × quantity:Headlight:
12 V, 60.0 W/55.0 W × 1
Tail/brake light:
LED
Front turn signal light: 12 V, 10.0 W × 2
Rear turn signal light: 12 V, 10.0 W × 2
Auxiliary light:
12 V, 5.0 W × 1
License plate light: 12 V, 5.0 W × 1
Meter lighting: LED
Neutral indicator light:
LED
High beam indicator light: LED Oil level warning light:
LED
Turn signal indicator light: LED
Fuel level warning light:
LED
Coolant temperature warning light: LED
Engine trouble warning light: LED
ABS warning light:
LED
Immobilizer system indicator light: LED
Shift timing indicator light: LED
Fuses:Main fuse:50.0 A
Headlight fuse: 15.0 A
Signaling system fuse:
7.5 A
Ignition fuse: 20.0 A
Parking lighting fuse: 7.5 A
Radiator fan motor fuse:
20.0 A
Sub radiator fan motor fuse: 7.5 A
Fuel injection system fuse: 15.0 A ABS control unit fuse:
7.5 A
ABS motor fuse: 30.0 A
ABS solenoid fuse:
15.0 A
Backup fuse: 7.5 A
Electronic throttle valve fuse: 7.5 A
U2CEE0E0.book Page 3 Wednesday, August 27, 2014 11:11 AM