2015 YAMAHA VMAX check oil

PERIODIC MAINTENANCE AND ADJUSTMENT
6-27
6
EAU22754
Changin g the brake an d
clutch flui dsHave a Yamaha dealer change the
brake and clutch fluids at the intervals
specified in the periodic maintenance
and lubrication chart. In addition, have
the oil seals of the brake and clutch
master cylinders and calipers as well
as the brake and clutch hoses replaced
at the intervals listed below or whenev-
er they are damaged or leaking.
 Oil seals: Replace every two
years.
 Brake and clutch hoses: Replace
every four years.
EAU23098
Checkin g an d lu bricatin g the
cab lesThe operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubri-
cated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or re-
place it. WARNING! Dama ge to the
outer housin g of cab les may result
in internal rustin g an d cause inter-
ference with cab le movement. Re-
place damag ed cab les as soon as
possi ble to prevent unsafe con di-
tions.
[EWA10712] EAU23115
Checkin
g an d lu bricatin g the
throttle grip an d ca bleThe operation of the throttle grip
should be checked before each ride. In
addition, the cable should be lubricat-
ed by a Yamaha dealer at the intervals
specified in the periodic maintenance
chart.
The throttle cable is equipped with a
rubber cover. Make sure that the cover
is securely installed. Even though the
cover is installed correctly, it does not
completely protect the cable from wa-
ter entry. Therefore, use care not to
pour water directly onto the cover or
cable when washing the vehicle. If the
cable or cover becomes dirty, wipe
clean with a moist cloth.
Recommen ded lu bricant:
Yamaha cable lubricant or other
suitable cable lubricant
U2CEE0E0.book Page 27 Wednesday, August 27, 2014 11:11 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-30
6
EAU23273
Checking the front forkThe condition and operation of the
front fork must be checked as follows
at the intervals specified in the periodic
maintenance and lubrication chart.
To check the con dition
Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation 1. Place the vehicle on a level sur- face and hold it in an upright posi-
tion. WARNING! To avoi d injury,
securely support the vehicle so
there is no dan ger of it fallin g
over.
[EWA10752]
2. While applying the front brake, push down hard on the handle-
bars several times to check if the
front fork compresses and re-
bounds smoothly.
NOTICE
ECA10591
If any damag e is foun d or the front
fork does not operate smoothly,
have a Yamaha d ealer check or re-
pair it.
EAU23284
Checkin g the steerin gWorn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Place a stand under the engine to raise the front wheel off the
ground. (See page 6-40 for more
information.) WARNING! To
avoi d injury, securely support
the vehicle so there is no dan ger
of it fallin g over.
[EWA10752]
2. Hold the lower ends of the front
fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steer-
ing.
U2CEE0E0.book Page 30 Wednesday, August 27, 2014 11:11 AM

MOTORCYCLE CARE AND STORAGE
7-4
7
EAU26244
StorageShort-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the mo-
torcycle.NOTICE
ECA10811
 Storin g the motorcycle in a
poorly ventilate d room or cover-
in g it with a tarp, while it is still
wet, will allow water an d humi d-
ity to seep in an d cause rust.
 To prevent corrosion, avoi d
d amp cellars, sta bles ( because
of the presence of ammonia)
an d areas where stron g chemi-
cals are stored .Long-term
Before storing your motorcycle for sev-
eral months: 1. Follow all the instructions in the “Care” section of this chapter. 2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to protect the cylinders, piston rings,
etc. from corrosion.a. Remove the spark plug caps and spark plugs.
b. Pour a teaspoonful of engine oil into each spark plug bore.
c. Install the spark plug caps onto the spark plugs, and then
place the spark plugs on the
cylinder head so that the elec-
trodes are grounded. (This will
limit sparking during the next
step.)
d. Turn the engine over several times with the starter. (This will
coat the cylinder walls with oil.)
WARNING! To prevent d am-
a g e or injury from sparkin g,
make sure to groun d the
spark plu g electro des while
turnin g the en gine over.
[EWA10952]
e. Remove the spark plug caps
from the spark plugs, and then
install the spark plugs and the
spark plug caps.
4. Lubricate all control cables and the pivoting points of all levers and
pedals as well as of the side-
stand/centerstand.
5. Check and, if necessary, correct the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlets with plastic bags to prevent moisture
from entering them.
7. Remove the battery and fully charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0 °C (30 °F) or more than 30
°C (90 °F)]. For more information
on storing the battery, see page
6-31.
U2CEE0E0.book Page 4 Wednesday, August 27, 2014 11:11 AM

10-1
10
INDEX
AABS....................................................... 3-21
ABS warning light ................................... 3-6
Air filter element.................................... 6-19
Auxiliary light bulb, replacing ............... 6-37BBattery .................................................. 6-31
Brake and clutch fluids, changing ........ 6-27
Brake and clutch levers,
checking and lubricating .................... 6-28
Brake and shift pedals, checking and lubricating .................... 6-28
Brake fluid level, checking.................... 6-25
Brake lever............................................ 3-20
Brake lever free play, checking ............ 6-24
Brake light switches ............................. 6-24
Brake pedal .......................................... 3-20CCables, checking and lubricating ......... 6-27
Care ........................................................ 7-1
Catalytic converters.............................. 3-24
Clutch lever.................................. 3-19, 6-23
Coolant ................................................. 6-16
Coolant temperature warning light ......... 3-5
Cowling and panels, removing and installing ........................ 6-8DDimmer switch...................................... 3-18EEngine break-in ...................................... 5-3
Engine idling speed, checking.............. 6-20
Engine oil and oil filter cartridge ........... 6-11
Engine serial number .............................. 9-1
Engine stop switch ............................... 3-18 Engine trouble warning light .................. 3-5
EXUP system ....................................... 3-31
FFinal gear oil ......................................... 6-14
Front and rear brake pads, checking ... 6-25
Front fork, adjusting ............................. 3-27
Front fork, checking ............................. 6-30
Fuel ...................................................... 3-23
Fuel consumption, tips for reducing ...... 5-3
Fuel level warning light........................... 3-5
Fuel tank breather hose and overflow
hose ................................................... 3-24
Fuel tank cap........................................ 3-22
Fuses, replacing ................................... 6-34HHandlebar switches ............................. 3-17
Hazard switch ...................................... 3-18
Headlight bulb, replacing ..................... 6-36
High beam indicator light ....................... 3-4
Horn switch .......................................... 3-18IIdentification numbers ........................... 9-1
Ignition circuit cut-off system .............. 3-32
Immobilizer system ................................ 3-1
Immobilizer system indicator light ......... 3-6
Indicator lights and warning lights ......... 3-4LLicense plate light bulb, replacing ....... 6-39
Luggage strap holders ......................... 3-31MMain switch/steering lock ...................... 3-2
Maintenance and lubrication, periodic... 6-4
Maintenance, emission control
system ................................................. 6-3 Matte color, caution................................ 7-1
Model label ............................................. 9-1
Multi-function display ............................. 3-8
NNeutral indicator light ............................. 3-4OOil level warning light .............................. 3-4PParking.................................................... 5-4
Part locations.......................................... 2-1
Pass switch........................................... 3-18SSafety information................................... 1-1
Seats ..................................................... 3-25
Shifting.................................................... 5-2
Shift pedal............................................. 3-19
Shift timing indicator light ....................... 3-6
Shock absorber assembly, adjusting ... 3-29
Sidestand.............................................. 3-31
Sidestand, checking and lubricating .... 6-29
Spark plugs, checking .......................... 6-10
Specifications ......................................... 8-1
Speedometer unit ................................... 3-7
Starting the engine ................................. 5-1
Start switch ........................................... 3-18
Steering, checking ................................ 6-30
Storage ................................................... 7-4
Supporting the motorcycle ................... 6-40
Swingarm pivots, lubricating ................ 6-29TTail/brake light ...................................... 6-38
Throttle grip and cable,
checking and lubricating .................... 6-27
Throttle grip free play, checking ........... 6-20
U2CEE0E0.book Page 1 Wednesday, August 27, 2014 11:11 AM