2015 YAMAHA VIKING bulb

Steering shaft lubrication .............. 8-39
Wheel removal .............................. 8-39
Tire replacement ........................... 8-40
Wheel installation .......................... 8-41
Battery ........................................... 8-42
Jump-starting ................................ 8-46
Fuse replacement ......................... 8-48
Replacing a headlight bulb ........... 8-50
Headlight beam adjustment .......... 8-53
Tail/brake light bulb replacement ................................ 8-53
Troubleshooting ............................ 8-55
Troubleshooting charts ................. 8-57
CLEANING AND STORAGE............ 9-1 Cleaning .......................................... 9-1
Storage............................................ 9-3
SPECIFICATIONS.......................... 10-1
CONSUMER INFORMATION ........ 11-1 Identification number records ....... 11-1
910111XP7C_EE.book Page 4 Monday, June 9, 2014 5:17 PM

8-50
8
9
10
11
12
13
14
EVU01670Replacing a he adlight bulbIf a headlight bulb burns out, replace it as fol-
lows.
1. Remove the cover at the rear of the headlight by pulling it off.1. Cover at the rear of the headlight
2. Remove the headlight bulb cover by pull- ing it off.1. Headlight bulb cover
1
1
1XP7C_EE.book Page 50 Monday, June 9, 2014 5:17 PM

8-51
1
2
3
4
5
6
78
9
10
11
12
13
14
3. Disconnect the headlight coupler.1. Headlight coupler
4. Unhook the headlight bulb holder.1. Headlight bulb holder
1
1
1XP7C_EE.book Page 51 Monday, June 9, 2014 5:17 PM

8-52
8
9
10
11
12
13
14
5. Wait for the headlight bulb to cool before touching or removing it. Remove the
burnt-out bulb by pulling it out.
6. Place a new headlight bulb into position, and then secure it with the bulb holder.
NOTICE: Do not touch the glass part
of the headlight bulb to keep it free
from oil, otherwise the transparency
of the glass, the luminosity of the
bulb, and the bulb life will be adverse-
ly affected. Thoroughly clean off any
dirt and fingerprints on the headlight
bulb using a cloth moistened with al-
cohol or thinner.
1. Do not touch the glass part of the bulb.7. Connect the headlight coupler.
8. Install the bulb cover and the cover at the rear of the headlight. NOTICE: Make
sure the headlight bulb cover is se-
curely fitted over the bulb holder and
seated properly.
9. Adjust the headlight beam if necessary.
1XP7C_EE.book Page 52 Monday, June 9, 2014 5:17 PM

8-53
1
2
3
4
5
6
78
9
10
11
12
13
14
EVU00990Headlight beam adjustmentNOTICEIt is advisable to have a Yamaha dealer
make this adjustment.To raise the beam, turn the headlight beam
adjusting screw in directiona.
To lower the beam, turn the headlight beam
adjusting screw in direction b.1. Headlight beam adjusting screw
EVU01000Tail/brake light bulb replacementIf a tail/brake light bulb burns out, replace it as
follows:
1. Remove panel A (if replacing the left tail/ brake light bulb) or panel B (if replacing
the right tail/brake light bulb) by removing
the quick fastener screws, nuts and bolts.1. Panel A
1
a
b
1
1XP7C_EE.book Page 53 Monday, June 9, 2014 5:17 PM

8-54
8
9
10
11
12
13
14
1. Panel B
1. Quick fastener screw ( × 7)
2. Panel front bolt and panel nut ( × 2)
3. Panel rear bolt 4. Panel A
2. Remove the tail/brake light bulb holder
(together with the bulb) by turning it coun-
terclockwise.1. Tail/brake light bulb holder3. Push the burnt-out bulb in and turn itcounterclockwise to remove it from the
bulb holder.
4. Push a new bulb in and turn it clockwise to install in the bulb holder.
5. Install the bulb holder (together with the bulb) by turning it clockwise.
6. Install the panel.
1
3
4
2 1
1
1XP7C_EE.book Page 54 Monday, June 9, 2014 5:17 PM

10-4
10
11
12
13
14
Vehicle load: 300 kg – maximum (661 lb – maximum):
Front:70.0 kPa (0.700 kgf/cm
2, 10 psi)
Rear:
120.0 kPa (1.200 kgf/cm2, 17 psi)
Front wheel:Wheel type:YXM700PF Panel wheel
YXM700PHF Panel wheel
YXM700PSF Cast wheel
Rim size: 12 × 6.0ATRear wheel:Wheel type:
YXM700PF Panel wheel
YXM700PHF Panel wheel
YXM700PSF Cast wheel
Rim size: 12 × 7.5ATFront brake:Type:
Disc brake
Operation: Unified brake
Recommended fluid:
DOT 4Rear brake:Type:Disc brake
Operation:
Unified brake Recommended fluid:
DOT 4
Front suspension:Type:
Double wishbone
Spring/shock absorber type: Coil spring/gas-oil damper
Wheel travel: 205 mm (8.1 in)Rear suspension:Type:Double wishbone
Spring/shock absorber type: Coil spring/gas-oil damper
Wheel travel:
205 mm (8.1 in)Electrical system:Ignition system:TCI
Charging system:
AC magnetoBattery:Model:U1-H11L
Voltage, capacity:
12 V, 28.0 AhHeadlight:Bulb type:Halogen bulb
1XP7C_EE.book Page 4 Monday, June 9, 2014 5:17 PM

10-5
1
2
3
4
5
6
7
8
910
11
12
13
14
Bulb voltage, wattage
× quantity:
Headlight:
12 V, 35.0/35.0 W × 2
Tail/brake light:
12 V, 5.0/21.0 W × 2
Neutral indicator light: LED
Reverse indicator light: LED
Coolant temperature warning light:
LED
Engine trouble warning light: LED
Parking brake indicator light: LED
On-Command four-wheel-drive/differential gear lock indica-
tor: LCD
High-range indicator light:
LED
Low-range indicator light: LED
Differential gear lock indicator light: LED
EPS warning light:
LED
Helmet/Seat belt indicator light: 14 V, 0.85 W × 2Fuses:Main fuse:
40.0 A
Fuel injection system fuse: 10.0 A EPS fuse:
40.0 A
Headlight fuse: 15.0 A
Signaling system fuse:
10.0 A
Ignition fuse: 10.0 A
Auxiliary DC jack fuse: 10.0 A
Backup fuse:
10.0 A
Four-wheel-drive motor fuse: 10.0 A
Radiator fan motor fuse: 25.0 A
For Europe only
The figures quoted are emission levels and
are not necessarily safe working levels. Whilst
there is a correlation between the emission
and exposure levels, this cannot be used reli-
ably to determine whether or not further pre-
cautions are required.
Factors that influence the actual level of expo-
sure of work-force include the characteristics
of the work room, the other sources of noise,
etc. i.e. the number of machines and other ad-
1XP7C_EE.book Page 5 Monday, June 9, 2014 5:17 PM