2015 YAMAHA MAJESTY S 125 fuel

PERIODIC MAINTENANCE AND ADJUSTMENT
6-4
2
3
4
567
8
9
EAU46921
Periodic maintenance chart for the emission control systemNO. ITEM CHECK OR MAINTENANCE JOB ODOMETER READING
ANNUAL
CHECK
1000 km
(600 mi) 6000 km
(3500 mi) 12000 km
(7000 mi) 18000 km
(10500 mi) 24000 km
(14000 mi)
1 * Fuel line Check fuel hoses for cracks or
damage. √√√√√√
2 Spark plug Check condition.
Clean and regap.
√√
Replace. √√
3 * Valves Check valve clearance.
Adjust. √√√√
4 * Fuel injection Check engine idle speed. √√√√√√
5 * Exhaust system Check for leakage.
Tighten if necessary.
Replace gasket(s) if necessary. √√√√√



PERIODIC MAINTENANCE AND ADJUSTMENT
6-17
1
2
3
4
56
7
8
9
EAU21385
Checking the throttle grip free
playThe throttle grip free play should mea-
sure 3.0–5.0 mm (0.12–0.20 in) at the
inner edge of the throttle grip. Periodi-
cally check the throttle grip free play
and, if necessary, have a Yamaha
dealer adjust it.
EAU21402
Valve clearanceThe valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.
EAU21879
TiresTires are the only contact between the
vehicle and the road. Safety in all con-
ditions of riding depends on a relatively
small area of road contact. Therefore, it
is essential to maintain the tires in good
condition at all times and replace them
at the appropriate time with the speci-
fied tires.
Tire air pressure
The tire air pressure should be checked
and, if necessary, adjusted before each
ride.
WARNING
EWA10504
Operation of this vehicle with im-
proper tire pressure may cause se-
1. Throttle grip free play
1



PERIODIC MAINTENANCE AND ADJUSTMENT
6-30
2
3
4
567
8
9
EAUT4110
Replacing a license plate light
bulb1. Remove the license plate light bulbsocket (together with the bulb) by
turning it counterclockwise, and
then pulling it out.
2. Remove the burnt-out bulb by pull- ing it out.
3. Insert a new bulb into the socket.
4. Install the socket (together with the bulb) by pushing it in, and then turn
it clockwise until it stops.
EAU54501
Auxiliary lightThis model is equipped with LED-type
auxiliary lights.
If an auxiliary light does not come on,
have a Yamaha dealer check it.
EAU25882
TroubleshootingAlthough Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur dur-
ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your scooter re-
quire any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the scooter prop-
erly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look like
Yamaha parts, but they are often inferi-
or, have a shorter service life and can
lead to expensive repair bills.
WARNING
EWA15142
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the ar-
ea, including pilot lights from water
1. License plate light bulb socket
1



PERIODIC MAINTENANCE AND ADJUSTMENT
6-32
2
3
4
567
8
9
EAU42706
Troubleshooting chartsStarting problems or poor engine performanceCheck the fuel level in
the fuel tank.1. Fuel
There is enough fuel.There is no fuel.
Check the battery.
Supply fuel.
The engine does not start.
Check the battery.
Operate the electric starter.4. Compression
There is compression.
There is no compression.
The engine does not start.
Have a Yamaha dealer check the vehicle.Have a Yamaha dealer check the vehicle.
Remove the spark plug
and check the electrodes.3. Ignition
Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug. Have a Yamaha dealer check the vehicle.
The engine does not start.
Check the compression.
Operate the electric starter.2. Battery
The engine turns over
quickly.
The engine turns over
slowly.
The battery is good.
DryWet
Operate the electric starter.
Check the battery lead connections,
and have a Yamaha dealer charge
the battery if necessary.
The engine does not start.
Check the ignition.



SCOOTER CARE AND STORAGE
7-2
1
2
3
4
5
67
8
9plenty of water, as it is harmful
to plastic parts.

Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.

Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.

For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid- den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on the
roads during winter are extremely cor-
rosive in combination with water, carry
out the following steps after each ride in
the rain, near the sea or on
salt-sprayed roads.TIPSalt sprayed on roads in the winter may
remain well into spring. 1. Clean the scooter with cold water and a mild detergent after the en-
gine has cooled down. NOTICE:
Do not use warm water since it
increases the corrosive action
of the salt.
[ECA10792]
2. Apply a corrosion protection spray on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
Cleaning the windshieldAvoid using any alkaline or strong acid
cleaner, gasoline, brake fluid, or any
other solvent. Clean the windshield with
a cloth or sponge dampened with a mild
detergent, and then wash it off thor-
oughly with water. For additional clean-
ing, use Yamaha Windshield Cleaner
or another high-quality windshield
cleaner. Some cleaning compounds for
plastics may leave scratches on the
windshield. Before using such clean-
ers, test an area of the windshield
which does not affect your visibility and
which cannot be easily recognized.



SCOOTER CARE AND STORAGE
7-4
1
2
3
4
5
67
8
9
EAU36564
StorageShort-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the scoot-
er.NOTICE
ECA10821

Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.

To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-cals are stored.
Long-term
Before storing your scooter for several
months: 1. Follow all the instructions in the “Care” section of this chapter. 2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to pro- tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING! To
prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.
[EWA10952]
4. Lubricate all control cables and the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
5. Check and, if necessary, correct the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlet with a plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0 ° C (30 °F) or more than 30
° C (90 °F)]. For more information
on storing the battery, see page
6-25.TIPMake any necessary repairs beforestoring the scooter.



8-1
2
3
4
5
6
789
SPECIFICATIONS
EAU5091K
Dimensions:Overall length:2030 mm (79.9 in)
Overall width: 715 mm (28.1 in)
Overall height: 1295 mm (51.0 in)
Seat height:
795 mm (31.3 in)
Wheelbase: 1405 mm (55.3 in)
Ground clearance: 93 mm (3.66 in)
Minimum turning radius:
2100 mm (82.7 in)Weight:Curb weight:148 kg (326 lb)Engine:Engine type:Liquid cooled 4-stroke, SOHC
Cylinder arrangement: Single cylinder
Displacement:
125 cm
3
Bore × stroke:
52.0 × 58.7 mm (2.05 × 2.31 in)
Compression ratio: 11.0 : 1
Starting system:
Electric starter
Lubrication system: Wet sump
Engine oil:Type:
SAE 10W-40
Recommended engine oil grade: API service SG type or higher, JASO stan-
dard MA or MB
*Engine oil quantity: Periodic oil change:
0.95 L (1.00 US qt, 0.84 Imp.qt)Final transmission oil:Type:SAE 10W-30 type SE motor oil
Quantity:
0.20 L (0.21 US qt, 0.18 Imp.qt)Cooling system:Coolant reservoir capacity (up to the maxi-
mum level mark):0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator capacity (including all routes): 0.56 L (0.59 US qt, 0.49 Imp.qt)
Air filter:Air filter element:Oil-coated paper elementFuel:Recommended fuel:Regular unleaded gasoline
Fuel tank capacity:
7.4 L (1.96 US gal, 1.63 Imp.gal)Fuel injection:*Throttle body:ID mark:52S1 01Spark plug(s):Manufacturer/model:
NGK / CPR8EA
Spark plug gap: 0.8–0.9 mm (0.031–0.035 in)Clutch:Clutch type:
Dry, centrifugal automaticTransmission:Primary reduction ratio:1.000
Final drive:
Gear
Secondary reduction ratio: 8.787 (45 / 13 × 33 / 13)
Transmission type: V-belt automaticChassis:Frame type:Backbone
Caster angle: 26.00 °
–20 –10 0 1020 30 40 50 C
10 30 50 70 90 110
0 130 F
SAE 10W-30
SAE 15W-40SAE 20W-40SAE 20W-50
SAE 10W-40SAE 10W-50



INDEXAAcceleration and deceleration....................5-2
Air filter and V-belt case air filter
elements ................................................6-15
Auxiliary light ............................................6-30BBattery......................................................6-25
Brake fluid, changing ...............................6-22
Brake fluid level, checking .......................6-21
Brake lever, front........................................3-7
Brake lever, rear ........................................3-7
Brake levers, lubricating...........................6-23
Braking .......................................................5-3CCables, checking and lubricating .............6-22
Care ...........................................................7-1
Catalytic converter ...................................3-10
Centerstand and sidestand, checking and
lubricating ..............................................6-23
Coolant.....................................................6-13
Coolant temperature warning light .............3-3DDimmer switch ...........................................3-7EEngine break-in ..........................................5-3
Engine idling speed, checking .................6-16
Engine oil .................................................6-10
Engine serial number .................................9-1
Engine trouble warning light.......................3-3FFinal transmission oil ...............................6-12
Front and rear brak e lever free play,
checking ................................................6-20
Front and rear brake pads, checking .......6-20 Front fork, checking ................................. 6-24
Front turn signal light ............................... 6-28
Fuel............................................................ 3-8
Fuel consumption, tips
for reducing........... 5-3
Fuel gauge................................................. 3-4
Fuel tank breather hose and overflow hose ........................................................ 3-9
Fuel tank cap ............................................. 3-8
Fuses, replacing ...................................... 6-27
HHandlebar switches ................................... 3-6
Headlight bulb, replacing ......................... 6-28
Helmet holder .......................................... 3-11
High beam indicator light ........................... 3-2
Horn switch ................................................ 3-7IIdentification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-15
Indicator lights and warning lights ............. 3-2KKeyhole cover ............................................ 3-2LLicense plate light bulb, replacing ........... 6-30
Luggage hook .......................................... 3-14MMain switch/steering lock........................... 3-1
Maintenance and lubrication, periodic ....... 6-5
Maintenance, emission control system...... 6-4
Matte color, caution ................................... 7-1
Model label ................................................ 9-1
Multi-function display ................................. 3-4PPanels, removing and installing ................. 6-8
Parking ...................................................... 5-4 Part locations ............................................ 2-1
Passenger footrest .................................. 3-11
Pass switch ............................................... 3-7
SSafe-riding points ...................................... 1-5
Safety information ..................................... 1-1
Seat ......................................................... 3-10
Shock absorber assembly ....................... 3-13
Sidestand ................................................ 3-14
Spark plug, checking ................................. 6-9
Specifications ............................................ 8-1
Starting off ................................................. 5-2
Starting the engine .................................... 5-1
Start switch................................................ 3-7
Steering, checking................................... 6-25
Storage...................................................... 7-4
Storage compartments ............................ 3-12TTachometer ............................................... 3-3
Tail/brake light ......................................... 6-28
Throttle grip and cable, checking and
lubricating ............................................. 6-22
Throttle grip free play, checking .............. 6-17
Tires ........................................................ 6-17
Tool kit....................................................... 6-2
Troubleshooting ...................................... 6-30
Troubleshooting charts............................ 6-32
Turn signal indicator lights ........................ 3-2
Turn signal light bulb (rear), replacing..... 6-29
Turn signal switch ..................................... 3-7VValve clearance....................................... 6-17
Vehicle identification number .................... 9-1