2015 VOLKSWAGEN PASSAT CC open hood

dipstick are located, see your authorized Volkswagen dealer or au-
thorized Volkswagen Service Facility for assistance.
5. Remove the dipstick from the guide tube and wipe the dipstick off
using a clean cloth.
6. Reinsert the dipstick into the guide tube and push it all the way in. If
there is an alignment tab on the engine oil dipstick, make sure it
lines up with the notch in the guide tube, and that the dipstick goes
all the way in.
7. Remove the dipstick again and read the oil level on the dipstick
⇒ fig. 165 as described below:
(A): Do not add any oil ⇒ . Continue with step 15.
(B): Oil may be added (about 1 pint / 0.5 liter). Continue with step 8
or step 15.
(C): You must add oil (about 1 quart / 1.0 liter). Continue with step
8.
8. After reading the oil level, reinsert the dipstick back into the guide
tube and push it all the way in.
9. Remove the cap on the engine oil filler opening ⇒ fig. 166.
10. Only add engine oil that Volkswagen has approved for that
engine. Add the oil gradually in small quantities (no more than
1 pint / 0.5 liter).
11. To help prevent overfilling, you must wait about 1 minute each
time you add oil so that the oil can flow into the oil pan up to the
marking on the dipstick.
12. Read the oil level on the dipstick again before adding another
small amount, if necessary. Never add too much oil ⇒ .
13. After adding oil, the level must at least be in the center of the
⇒ fig. 165 (B) area, but never above (A) ⇒ .
14. After adding oil, securely install the cap on the engine oil filler
opening. Otherwise, oil could leak out while the engine is running.
15. Insert the oil dipstick back in the guide tube and push it all the
way in.
16. Close the hood ⇒ 
Engine oil level ranges

WARNING
Hot steam and hot engine coolant can cause serious burns.
Never open the hood if you see steam or coolant escaping
from the engine compartment. Always wait until you no longer
see or hear steam or coolant escaping from the engine.
Always let the engine cool down completely before carefully
opening the hood. Hot components will burn skin on contact.
When the engine has cooled down and you are ready to open
the hood:
– Apply the electronic parking brake and shift the transmis-
sion into Park (P) (automatic) or Neutral (manual only).
– Take the vehicle key out of the ignition.
– On vehicles with Keyless Access, make sure that the re-
mote control vehicle key is out of range of the vehicle and
that the vehicle cannot be started by depressing the starter
button
– Always keep children and others away from the engine
compartment and never leave them unsupervised.
The engine coolant system is under pressure when the en-
gine is hot. Never unscrew the coolant expansion tank cap
when the engine is hot. Hot coolant can spray out and cause
severe burns and other serious injuries.
– Turn the cap slowly and very carefully in a counterclock-
wise direction while applying light downward pressure on the
top of the cap.
– Always protect your face, hands, and arms from hot escap-
ing coolant or steam by covering the cap with a large, thick
rag.
Never spill fluids on the engine or exhaust system when re-
filling. Spilling fluids onto hot parts of the engine or exhaust
system can cause a fire. Under some conditions, the ethylene
glycol in engine coolant can catch fire.
NOTICE
Use distilled water only when adding coolant! All other types
of water contain chemical compounds that can cause extensive
corrosion damage to the engine. This can even lead to engine

Rinse the sponge or glove thoroughly and often.
Clean the wheels and under the door sills last. Use a different sponge
or wash mitt.
WARNING
After the vehicle has been washed, the wet brakes or, in winter,
brake discs or pads coated with ice, react slower and need
longer stopping distances.
Always dry the brakes and clean off any ice coatings with a
few careful applications of the brake. Make sure not to endan-
ger other motorists or cyclists or disobey legal requirements.
CAUTION
Sharp edges under the vehicle can cut exposed skin.
Always protect your hands and arms from cuts on sharp
metal edges when cleaning the underbody, the inside of the
wheel housings, etc.
NOTICE
The water temperature must not be more than +140 °F
(+60 °C).
To help prevent damage to the paint, do not wash the vehicle
in direct sunlight.
Do not use insect sponges, abrasive kitchen sponges or simi-
lar things to clean the vehicle. These can damage the paint fin-
ish.
Never clean headlights with a dry cloth or sponge. Always use
a wet cloth or sponge. For best results use soapy water.
When washing or rinsing the vehicle in cold weather, do not
let water get into the lock cylinders or point the hose at gaps
around the doors, hood, or luggage compartment lid. The water
could freeze on the locks and seals and make it difficult to open
the vehicle!

NOTICE
To help prevent vehicle damage in a car wash:
Compare the vehicle track width with the dimensions of the
guide rails in the car wash to help prevent damage to wheel rims
and tires!
Switch off the rain sensor before driving the vehicle through a
car wash ⇒  Rain sensor.
Make sure there is enough clearance for the height and width
of the vehicle.
To help prevent paint damage to the engine hood, place wiper
blades against the windshield after they have dried. Do not let
them snap back into place.
Fold the outside mirrors toward the vehicle body. Do not fold
power folding mirrors manually!
Lock the luggage compartment lid to help prevent uninten-
tional opening in the car wash.
Washing with a power washer

Opening the fuse box in the instrument panel
Insert a flat object, such as a screwdriver from the vehicle tool kit,
into the opening ⇒ fig. 196 (arrow) and carefully lift off the cover.
On the inside of the cover there are plastic tweezers for removing
and inserting fuses.
To install, guide the cover from the bottom into the instrument
panel and push until you can hear it latch into place.
Opening the fuse box in the engine compartment
Open the engine hood

7. Insert the bulb holder with the new bulb in the original position
in the headlight housing (3).
8. Install the rubber cover ⇒ fig. 200 (1).

Replacing the cornering light bulb

1. Please review and follow the checklist
2. Open the hood