2015 VOLKSWAGEN CC heater

Accessory weight
The combined weight (in excess of those standard items which may
be replaced) of automatic transmission, electro-mechanical power
steering, power brakes, power windows, power seats, radio, and
heater, to the extent that these items are available as factory-installed
equipment (whether installed or not).
Aspect ratio
The ratio of sidewall height to tire width, expressed as a percentage.
A number of 70 (0.7:1 or 70%) or lower indicates a low-profile tire with
a shorter sidewall for improved steering response and better overall
handling on dry pavement.
Bead
The part of a tire made of steel wires, wrapped or reinforced by ply
cords, with the shape and structure to ensure proper fit to the wheel
rim.
Bead separation
A breakdown of the bond between components in the bead.
Carcass
The tire structure, except tread and sidewall rubber which, when in-
flated, bears the load.
Chunking
The breaking away of pieces of the tread or sidewall.
Cord
The strands of material forming the plies in the tire.
Cord separation
The parting of cords from adjacent rubber compounds.
Cracking
Any parting within the tread, sidewall, or inner liner of the tire extend-
ing to cord material.
Cold tire inflation pressure
The tire pressure recommended by the vehicle manufacturer for a tire
of a specified size that has not been driven for more than a couple of

WARNING
Operating fluids and some materials in the engine compartment
can catch fire easily, causing burns and other serious personal
injuries!
Never smoke near the engine compartment.
Never work next to open flames or sparks.
Never pour or spill operating fluids or other flammable liq-
uids on the engine. These fluids can ignite on hot engine parts
and cause injuries.
If work on the fuel system or the electrical system is neces-
sary:
– Always disconnect the 12 Volt vehicle battery. Make sure
the vehicle is unlocked when you disconnect the battery, or
the alarm will go off. Never touch the electrical wiring of the
ignition system.
– Never work near heaters, water heaters, or other open
flames.
Always have a functional, approved fire extinguisher nearby.
NOTICE
When changing or topping off fluids, make sure that you pour
the fluids into the correct reservoirs. Adding the wrong type of
operating fluids will cause serious malfunctions and engine
damage.
Fluid leaks and spills are harmful to the environment. Regularly
check the ground underneath your vehicle for this reason. If you find
spots of oil or other fluids, have your vehicle checked by your author-
ized Volkswagen dealer or authorized Volkswagen Service Facility.
Dispose of leaked operating fluids properly.
Display

WARNING
Engine coolant is poisonous!
Always keep the coolant in its original container stored in a
safe place.
To reduce the risk of poisoning, never store engine coolant in
empty food or beverage containers or in any other containers
that might mislead someone into drinking from them.
Always keep engine coolant out of reach of children.
Always make sure there is enough of the correct coolant ad-
ditive to provide proper antifreeze protection at the coldest
temperatures that can be expected where the vehicle will be
used.
At extremely cold temperatures, the coolant could freeze,
causing the vehicle to break down. The heater would also not
work, and vehicle occupants could be without protection at
subfreezing temperatures.
Coolant and coolant additives can pollute the environment. Col-
lect leaking operating fluids and dispose of them properly in accord-
ance with applicable environmental laws and regulations.
Warning light and engine coolant temperature gauge

Fig. 167 Engine coolant temperature gauge in the instrument cluster:
A Engine cold; B Normal temperature range; C Warning zone.

When adding engine coolant, use a mixture of distilled water and at
least 40% coolant additive G 13 or G 12 plus-plus (TL-VW 774 G) for
optimum corrosion protection ⇒ .
Do not mix G 13 with G 12 plus or G 11. Mixing these coolant addi-
tives together significantly reduces corrosion protection ⇒  and can
lead to engine damage that is not covered by any Volkswagen Lim-
ited Warranty.
WARNING
Too little antifreeze protection in the engine cooling system can
cause engine failure and severe injuries.
Always make sure there is enough of the correct coolant ad-
ditive to provide proper antifreeze protection at the coldest
temperatures that can be expected where the vehicle will be
used.
At extremely cold temperatures, the coolant could freeze,
causing the vehicle to break down. The heater would also not
work, and vehicle occupants could be without protection at
subfreezing temperatures.
NOTICE
Never mix original Volkswagen engine coolant additives with
other additives not approved by Volkswagen. Mixing
Volkswagen coolant additives with coolant additives made by
other manufacturers can seriously damage the engine and the
engine cooling system.
If the fluid in the engine coolant reservoir is any color but pink,
then G 13 was mixed with a different engine coolant. If this is the
case, the engine coolant must be replaced immediately. Other-
wise serious malfunctions or engine damage can occur!
Engine coolant and engine coolant additives can pollute the envi-
ronment. Collect leaking operating fluids and dispose of them proper-
ly in accordance with applicable environmental laws and regulations.

jump-start terminal6 ⇒ Positive jump start terminal, 3.6 liter engine,
⇒ fig. 210 (+).
3. Attach one end of the red jumper cable to the positive terminal (+)
of the dead battery: (1) ⇒ .
4. Attach the other end of the red jumper cable to the positive termi-
nal (+) of the good battery (booster battery): (2).
5. Attach one end of the black jumper cable to the negative terminal
(-) of the booster battery: (2) ⇒ fig. 211.
6. Attach the other end of the black jumper cable (3) to a bare metal
part of the vehicle with the dead battery. This part should be
connected directly to the engine block. You may also attach the
cable to the engine block itself. Attach the clamp to a point that is
as far away as possible from the dead battery (1) ⇒ .
7. Route the jumper cables so that they cannot get caught in any
moving parts in the engine compartment of either vehicle.
Starting the engine
Start the engine of the vehicle with the good battery that is provid-
ing help and let it run at idle speed.
Turn on the ignition of the vehicle with the dead battery. If the en-
gine starts, wait 2 to 3 minutes until it “runs smoothly” before remov-
ing the jumper cables as described below ⇒ . If the engine does not
start within about 10 seconds, turn off the ignition and wait at least
1 minute; then try again.
Before removing the jumper cables
Switch off the headlights (if they are on).
In the vehicle with the dead battery, switch on the heater fan and
the rear window defroster. This helps to minimize voltage spikes
when the cables are disconnected.
Removing jumper cables
With the engine running, remove the jumper cables in reverse order
to the way they were connected.
1. Disconnect the black (-) cable from the vehicle with the dead bat-
tery.

6 For vehicles without a battery in the engine compartment, see ⇒ page 587, Positive jump start terminal, 3.6 liter engine