2015 VAUXHALL ASTRA J torque

Driving and operating161
Do not operate the accelerator pedal.Diesel engine: turn the key to position2 for preheating until control
indicator ! extinguishes.
Turn the key briefly to position 3 and
release: an automatic procedure
operates the starter with a short delay
as long as the engine is running, see
Automatic Starter Control.
Before restarting or to switch off the
engine, turn the key back to position
0 .
During an Autostop, the engine can
be started by depressing the clutch
pedal.Starting the vehicle at low
temperatures
The start of the engine without
additional heaters is possible down to -25 °С for diesel engines and -30 °C
for petrol engines. Required is an engine oil with the correct viscosity,
the correct fuel, performed services
and a sufficiently charged battery.
With temperatures below -30 °C the
automatic transmission need a
warming phase of approx. 5 minutes.
The selector lever must be in position P .
Automatic Starter Control
This function controls the engine
starting procedure. The driver does
not have to hold the key in position 3.
Once applied, the system will go on
starting automatically until the engine
is running. Because of the checking
procedure, the engine starts running
after a short delay.Possible reasons for a non-starting
engine:
■ Clutch pedal not operated (manual transmission)
■ Brake pedal not operated or selector lever not in P or N
(automatic transmission)
■ Timeout occurred
Turbo engine warm-up
Upon start-up, engine available
torque may be limited for a short time, especially when the engine
temperature is cold. The limitation is
to allow the lubrication system to fully
protect the engine.
Overrun cut-off The fuel supply is automatically cut off
during overrun, i.e. when the vehicle
is driven with a gear engaged but accelerator is released.

Driving and operating209
At speeds below 35 mph the system
is inoperable.
Fault
The lane departure warning system
may not operate properly when:
■ the windscreen is not clean
■ there are adverse environmental conditions like heavy rain, snow,
direct sunlight or shadows
The system can not operate when no
lane marking is detected.Fuel
Fuel for petrol enginesOnly use unleaded fuel that complies
with European standard EN 228 or
E DIN 51626-1 or equivalent.
Your engine is capable to run with
E10 fuel that fulfills these standards.
E10 fuel contains up to 10 %
bioethanol.
Use fuel with the recommended
octane rating 3 291. Use of fuel with
too low an octane rating can reduce
engine power and torque and slightly increases fuel consumption.Caution
Do not use fuel or fuel additives
that contain metallic compounds
such as manganese-based
additives. This may cause engine
damage.
Caution
Use of fuel that does not comply to EN 228 or E DIN 51626-1 or
equivalent can lead to deposits or
engine damage and may affect
your warranty.
Caution
Use of fuel with too low an octane
rating could lead to uncontrolled combustion and engine damage.
Fuel for diesel engines
Only use diesel fuel that complies
with EN 590.
In countries outside the European
Union use Euro-Diesel fuel with a
sulphur concentration below 50 ppm.

270Vehicle care
Attach jack handle and with the
jack correctly aligned rotate handle until wheel is clear of theground.
Sports Tourer, jack variant 2,
3 255:
Set the jack to the necessary
height. Position it directly below
the jacking point in a manner that
prevents it from slipping.
Attach wheel wrench and with the
jack correctly aligned rotate wheel wrench until wheel is clear of the
ground.
5. Unscrew the wheel nuts. 6. Change the wheel. Spare wheel 3 271.
7. Screw on the wheel nuts.
8. Lower the vehicle and remove jack.
9. Install the wheel wrench ensuring that it locates securely and tighten
each nut in a crosswise
sequence. Tightening torque is
140 Nm.
10. Align the valve hole in the wheel cover with the tyre valve before
installing.
Install wheel nut caps.
Install centre cap on alloy wheels.
11. Install vehicle jacking point cover on versions with sill panelling.
12. Stow the replaced wheel 3 271,
the vehicle tools 3 255 and the
key adapter 3 59.
13. Check the tyre pressure of the installed tyre and the wheel nut
torque as soon as possible.
Have the defective tyre renewed or
repaired as soon as possible.

Technical data291Engine dataSales designation1.41.41.41.41.61.61.6
Engine identifier code
A14XELA14XERA14NELA14NET
LPGA16XERA16XHTA16SHTNumber of cylinders4444444Piston displacement [cm 3
]1398139813641364159815981598Engine power [kW]64748810385125147at rpm600060004200-60004900-6000600060005500Torque [Nm]130130200200155260280at rpm400040001850-42001850-490040001650-32001650-3500Fuel typePetrolPetrolPetrolPetrol/LPGPetrolPetrolPetrolOctane rating RONrecommended95959595959898possible98989898989595possible91919191919191Gas–––LPG–––Engine oil consumption [l/1000 km] 2)0.60.60.60.60.60.60.62)
Maximum value.

292Technical data
Sales designation1.82.0 VXR1.31.61.61.71.7Engine identifier codeA18XERA20NFTA13DTEB16DTHB16DTLA17DTNA17DTCNumber of cylinders4444444Piston displacement [cm3
]1796199812481598159816861686Engine power [kW]10320670100817481at rpm6300530040003500-4000350040004000Torque [Nm]175400190320300260280at rpm38002400-48001750-325020001750-20001750-25001750-2500Fuel typePetrolPetrolDieselDieselDieselDieselDieselOctane rating RONrecommended9598possible9895possible9191Engine oil consumption [l/1000 km] 3)0.60.60.60.60.60.60.63)
Maximum value.

Technical data293
Sales designation1.71.71.72.0 Turbo2.0 TurboEngine identifier codeA17DTEA17DTFA17DTSA20DTHA20DTRNumber of cylinders44444Piston displacement [cm3
]16861686168619561956Engine power [kW]819696121143at rpm40004000400040004000Torque [Nm]280300300350400at rpm1750-25002000-25002000-25001750-25001750-2500Fuel typeDieselDieselDieselDieselDieselEngine oil consumption [l/1000 km] 2)0.60.60.60.60.62)
Maximum value.