2015 TOYOTA YARIS HYBRID light

2054-3. Operating the lights and wipers
4
Driving
YARIS_HV_EE_OM52F30E
■ If no windshield washer fluid sprays
Check that the washer nozzle is not blocked, if there is washer fluid in the
windshield washer fluid reservoir.
WARNING
■ Caution regarding the use of windshield wiper in “AUTO” mode (vehi-
cles with a rain-sensing windshield wiper)
The windshield wiper may operate unexpectedly if the sensor is touched or
the windshield is subject to vibration in “AUTO” mode. Take care that your
fingers, etc., do not become caught in the windshield wiper.
■ Caution regarding the use of washer fluid
When it is cold, do not use the washer fluid until the windshield becomes
warm. The fluid may freeze on the windshield and cause low visibility. This
may lead to an accident, resulting in death or serious injury.
NOTICE
■ When the windshield is dry
Do not use the wiper, as they may damage the windshield.
■ When there is no washer fluid spray from the nozzle
Damage to the washer fluid pump may be caused if the lever is pulled
toward you and held continually.
■ When a nozzle becomes blocked
In this case, contact any authorized Toyota dealer or repairer, or another
duly qualified and equipped professional.
Do not try to clear it with a pin or other object. The nozzle will be damaged.

2064-3. Operating the lights and wipers
YARIS_HV_EE_OM52F30E
Rear window wiper and washer∗
Turning the end of the lever turns on the rear window wiper and
washer.
Off
Intermittent window wiper
operation
Normal window wiper
operation
Washer/wiper dual opera-
tion
Washer/wiper dual opera-
tion
The wiper will automatically
operate a couple of times
after the washer squirts.
■ The rear window wiper and washer can be operated when
XVehicles without a smart entry & start system
The power switch is in the “ON” position.
XVehicles with a smart entry & start system
The power switch is in ON mode.
■ If no washer fluid sprays
Check that the washer nozzle is not blocked, if there is washer fluid in the
washer fluid reservoir.
∗: If equipped
Operation instructions
1
2
3
4
5

2074-3. Operating the lights and wipers
4
Driving
YARIS_HV_EE_OM52F30E
NOTICE
■ When the rear window is dry
Do not use the wiper, as it may damage the rear window.
■ When the washer fluid tank is empty
Do not operate the switch continually as the washer fluid pump may over-
heat.
■ When a nozzle becomes blocked
In this case, contact any authorized Toyota dealer or repairer, or another
duly qualified and equipped professional.
Do not try to clear it with a pin or other object. The nozzle will be damaged.

2104-4. Refueling
YARIS_HV_EE_OM52F30E
Pull up the opener to open the
fuel filler door.
Turn the fuel tank cap slowly to
open.
After refueling, turn the fuel tank
cap until you hear a click. Once
the cap is released, it will turn
slightly in the opposite direction.
Opening the fuel tank cap
1
2
Closing the fuel tank cap
WARNING
■ When replacing the fuel tank cap
Do not use anything but a genuine Toyota fuel tank cap designed for your
vehicle. Doing so may cause a fire or other incident which may result in
death or serious injury.

2144-5. Toyota Safety Sense
YARIS_HV_EE_OM52F30E
NOTICE
■ Front sensor
Observe the following to ensure that the sensor operates correctly:
B: Approximately 20 cm (7.9 in.) (Approximately 10 cm (4.0 in.) to the right and left from the center of the front sensor)
● Do not attach window tinting to the windshield.
● If the part of the windshield in front of the front sensor is fogged up or cov- ered with condensation or ice, use the windshield defogger to remove thefog, condensation or ice.
● Keep the windshield clean at all times. The pre-crash safety system may not function properly if the windshield isdirty or covered with an oily film, water droplets, snow, etc. If the inner side of the windshield where the front sensor is installed is dirty,do not attempt to remove the front sensor. Contact any authorized Toyotadealer or repairer, or another dul y qualified and equipped professional.
● If the windshield needs to be replaced, contact any authorized Toyota dealer or repairer, or another dul y qualified and equipped professional.
● Do not install an antenna in front of the sensor.
● Do not spill liquid onto the sensor.
● Do not allow bright lights to shine into the sensor.
●Do not damage or let the lenses of the front sensor get dirty. When cleaning the inner side of the windshield, do not let glass cleaner con-tact the lenses. Also, do not touch the lenses. For proper care of the lenses of the front sensor, contact any authorizedToyota dealer or repairer, or another duly qualified and equipped profes-sional.
●Do not change the installation position or direction of the sensor or remove it.The direction of the sensor is precisely adjusted.
●Do not subject the sensor to strong impact or disassemble it.
●Do not install an electronic device or device that emits strong electric wavesnear the front sensor.
●Do not place reflective objects on top of the instrument panel.
● Do not attach stickers, including trans- parent stickers, or other items to theouter side of the windshield in front ofthe front sensor (shaded area in the illustration).
A: From the top of the windshield to approximately 10 cm (4.0 in.) below the bottom of the front sensor
● Do not install or attach anything to the inner side of the windshield under thefront sensor (shaded area in the illustra-tion).
A: Approximately 10 cm (4.0 in.) (Starting from the bottom of the front sensor)
B: Approximately 20 cm (7.9 in.) (Approx- imately 10 cm (4.0 in.) to the right and leftfrom the center of the front sensor)

2164-5. Toyota Safety Sense
YARIS_HV_EE_OM52F30E
■Changing the pre-crash warning timing
Each time the PCS switch is
pressed, the warning timing
changes as follows:
Far (operation starts earlier)
Middle (default setting)
Near (operation starts later)
When the PCS switch is
pressed to turn the system on,
the PCS activation indicator will
turn on and the current warning
timing will be displayed on the
multi-information display.
■Disabling the pre-crash safety system
Press the PCS switch for 3 sec-
onds or more.
The PCS warning light will turn
on and a message will be dis-
played on the multi-information
display.
To enable the system, press the
PCS switch again.
Vehicles without a smart entry &
start system: The system is
enabled each time the power
switch is turned to the “ON”
position.
Vehicles with a smart entry &
start system: The system is
enabled each time the power
switch is turned to IGNITION
ON mode.
Changing the pre-crash safety system
1
2
3

2174-5. Toyota Safety Sense
4
Driving
YARIS_HV_EE_OM52F30E
■Operational conditions
The pre-crash safety system is enabled and determines that the possibility of
a frontal collision with a vehicle (e xcept motorcycles and bicycles) is high.
● Pre-crash warning:
• Vehicle speed is approximately 15 to 140 km/h (10 to 86 mph).
• The relative speed between your vehicle and the vehicle ahead is greater
than approximately 15 km/h (10 mph).
● Pre-crash brake assist:
• Vehicle speed is approximately 30 to 80 km/h (19 to 49 mph).
• The relative speed between your vehicle and the vehicle ahead is greater
than approximately 30 km/h (19 mph).
● Pre-crash braking:
• Vehicle speed is approximately 10 to 80 km/h (7 to 49 mph).
• The relative speed between your vehicle and the vehicle ahead is greater
than approximately 10 km/h (7 mph).
The system may not operate in the following situations:
● If a battery terminal has been disconnected and reconnected and then the
vehicle has not been driven for a certain amount of time
● If VSC is disabled (only the pre-crash warning function will be operational)
● If the PCS warning light is flashing or illuminated
■ Cancelation of the pre-crash braking
● If either of the following situations occur while the pre-crash braking function
is operating, it will be canceled:
• The accelerator pedal is depressed strongly.
• The steering wheel is turned sharply or abruptly.
● If the vehicle is stopped by the operation of the pre-crash braking function,
the operation of the pre-crash braking function will be canceled after the
vehicle has been stopped for approximately 2 seconds.

2184-5. Toyota Safety Sense
YARIS_HV_EE_OM52F30E
■ Conditions under which the system may operate even if there is no pos-
sibility of a collision
In the following situations the sensor may detect an object and cause the sys-
tem to determine that there is a possibility of a frontal collision and operate.
When there is an object (traffic sign, guard rail, etc.) by the roadside at
the entrance of a curve
When passing an oncoming vehicle on a curve
When passing an oncoming vehicle while making a left or right turn
When rapidly closing on a preceding vehicle
When rapidly closing on an electric toll gate barrier, parking area barrier,
or other barrier that opens and closes
When approaching an overpass, traffic sign, billboard, etc.
When the front part of the vehicle is raised or lowered
When the sensor is misaligned due to a strong impact being applied to
the sensor, etc.
When there is a structural object (billboard, street light, etc.) at the top of
an uphill road
When there is a metal object (manhole cover, steel plate, etc.) at the bot-
tom of a downhill road
When approaching a low hanging object that may contact the vehicle,
such as a banner or tree branches
When driving through dense fog or smoke
When the vehicle is hit by water or snow from a preceding vehicle, etc.
1
2
3
4
5
6
7
8
9
10
11
12
13