2015 TOYOTA YARIS HATCHBACK low beam

852. Instrument cluster
2
Instrument cluster
YARIS_F_WE_52G04E
Warning lights inform the driver of malfunctions in the indicated vehi-
cle’s systems.
Warning lights
*1
Brake system warning
light ( P. 431)
*2
(Yellow)
Automatic High Beam
indicator ( P. 434)
*1
Charging system warn-
ing light ( P. 431)
*2
(Yellow)
Cruise control indicator
( P. 434)
*1
Low engine oil pressure
warning light ( P. 431)
*2
(Yellow)
LDA indicator
( P. 434)
*1
(Red)
High engine coolant
temperature warning
light ( P. 431)
*2, 9
(Yellow)
Lane marker indicators
( P. 434)
*1
Malfunction indicator
lamp ( P. 432)
*2
(Yellow)
Speed limiter indicator
( P. 434)
*1
SRS warning light
( P. 432)
*1, 2, 5
Stop & Start cancel indi-
cator ( P. 434)
*1
ABS warning light
( P. 432)
*1, 6
Fuel filter warning light
( P. 434)
*1Electric power steering
system warning light
( P. 432)
*2, 3
(Yellow)
Smart entry & start sys-
tem indicator
( P. 435)
*1, 2, 5
PCS warning light
( P. 433)
Open door warning light
( P. 435)
*1, 2, 4
Slip indicator
( P. 433)
Low fuel level warning
light ( P. 435)

872. Instrument cluster
2
Instrument cluster
YARIS_F_WE_52G04E
The indicators inform the driver of the operating state of the vehicle’s
various systems.
Indicators
Turn signal indicator
( P. 202)
*5
“SPORT” indicator
( P. 194)
Headlight high beam
indicator ( P. 205)
*1, 7
Gear Shift Indicator
( P. 200)
*2
(Green)
Automatic High Beam
indicator ( P. 241)
*2
(Green)
Cruise control indicator
( P. 245)
Tail light indicator
( P. 204)
*2
“SET” indicator
( P. 245)
*2
Front fog light indicator
( P. 210)
*2
(Green)
LDA indicator
( P. 236)
Rear fog light indicator
( P. 210)
*2, 12
(Green)
Lane marker indicators
( P. 237)
*2
(Green)
Smart entry & start sys-
tem indicator
( P. 187)
*2
(Green)
Speed limiter indicator
( P. 249)
*3
(Blue)
Low engine coolant tem-
perature indicator
*1, 2Stop & Start indicator
( P. 253)
*4Engine preheating indi-
cator ( P. 184, 187)
*1, 2
Stop & Start cancel indi-
cator ( P. 254)
*1, 5, 6Eco Driving Indicator
Light ( P. 166)
*1, 2, 8
Slip indicator (P. 261)

2054-3. Operating the lights and wipers
4
Driving
YARIS_F_WE_52G04E
With the headlights on, push
the lever away from you to turn
on the high beams.
Pull the lever toward you to the
center position to turn the high
beams off.
Pull the lever toward you and
release it to flash the high
beams once.
You can flash the high beams with the headlights on or off.
This system allows the low beam headlights to be turned on for 30
seconds when the engine switch is turned off.
Pull the lever toward you and
release it with the light switch is in
or after turning the
engine switch off.
Pull the lever toward you and
release it again to turn off the
lights.
Turning on the high beam headlights
1
2
Follow me home system

2224-5. Toyota Safety Sense
YARIS_F_WE_52G04E
Toyota Safety Sense
◆PCS (Pre-Crash Safety system)
 P. 2 2 7
◆LDA (Lane Departure Alert)
 P. 2 3 6
◆Automatic High Beam
 P. 2 4 1
: If equipped
The Toyota Safety Sense system consists of the following drive
assist systems and contributes to a safe and comfortable driv-
ing experience.

2424-5. Toyota Safety Sense
YARIS_F_WE_52G04E
When all of the following conditions are fulfilled, high beam will be
automatically turned on:
● Vehicle speed is above approximately 40 km/h (25 mph).
● The area ahead of the vehicle is dark.
● There are no oncoming or preceding vehicles with headlights or tail
lights turned on.
● There are few streetlights on the road ahead.
If any of the following conditions are fulfilled, high beam will be auto-
matically turned off:
● Vehicle speed drops below approximately 30 km/h (19 mph).
● The area ahead of the vehicle is not dark.
● Oncoming or preceding vehicles have headlights or tail lights
turned on.
● There are many streetlights on the road ahead.
■Switching to low beam
Pull the lever to original posi-
tion.
The Automatic High Beam indi-
cator will turn off.
Push the lever away from you to
activate the Automatic High
Beam system again.
High beam automatic turning on or off conditions
Turning the high beam on/off manually

2434-5. Toyota Safety Sense
4
Driving
YARIS_F_WE_52G04E
■Switching to high beam
Press the Automatic High
Beam switch.
The Automatic High Beam indi-
cator will turn off and the head-
light high beam indicator will
turn on.
Press the switch to activate the
Automatic High Beam system
again.
■ The Automatic High Beam can be operated when
Vehicles without a smart entry & start system
The engine switch is in the “ON” position.
Vehicles with a smart entry & start system
The engine switch is in IGNITION ON mode.
■ Front sensor detection information
● High beam may not be automatically turned off in the following situations:
• When oncoming vehicles suddenly appear from a curve
• When the vehicle is cut in front of by another
• When oncoming or preceding vehicles are hidden from sight due to
repeated curves, road divi ders or roadside trees
● High beam may be turned off if an oncoming vehicle that is using fog lights
without using the headlights is detected.
● House lights, street lights, red traffic signals, and illuminated billboards or
signs may cause the high beam to turn off.
● The following factors may affect the amount of time taken to turn high beam
on or off:
• The brightness of headlights, fog lights, and tail lights of oncoming and
preceding vehicles
• The movement and direction of oncoming and preceding vehicles
• When a oncoming or preceding vehicle only has operational lights on one
side
• When a oncoming or preceding vehi cle is a two-wheeled vehicle
• The condition of the road (gradient, curve, condition of the road surface,
etc.)
• The number of passengers and amount of luggage

2444-5. Toyota Safety Sense
YARIS_F_WE_52G04E
● High beam may be turned on or off when unexpected by the driver.
● In the situations below, the system may not be able to correctly detect the surrounding brightness levels, and may flash or expose nearby pedestrians to the high beam. Therefore, you shoul d consider turning the high beams on or off manually rather than relying on the Automatic High Beam system.
• In bad weather (rain, snow, fog, sandstorms, etc.) • The windshield is obscured by fog, mist, ice, dirt, etc.• The windshield is cracked or damaged.• The front sensor is deformed or dirty. • The front sensor temperature is extremely high. • Surrounding brightness levels are equal to those of headlights, tail lightsor fog lights.• Vehicles ahead have headlights or tail lights that are either switched off,dirty, are changing color, or are not aimed properly.• When driving through an area of intermittently changing brightness anddarkness. • When frequently and repeatedly driving ascending/descending roads, or roads with rough, bumpy or uneven surfaces (such as stone-pavedroads, gravel tracks, etc.).• When frequently and repeatedly taking curves or driving on a windingroad.• There is a highly reflective object ahead of the vehicle, such as a sign or a mirror. • The back of a vehicle ahead is highly reflective, such as a container on atruck.• The vehicle’s headlights are damaged or dirty.• The vehicle is listing or titling, due to a flat tire, a trailer being towed, etc.• The driver believes that the high beam may be causing problems or dis- tress to other drivers or pedestrians nearby.
■ If the Automatic High Beam indicator comes on in yellow
It may indicate a malfunction in the system. Contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional.
WARNING
■ Limitations of the Automatic High Beam
Do not rely on the Automatic High Beam. Always drive safely, taking care to
observe your surroundings and turning high beam on or off manually if nec-
essary.
NOTICE
■ Notes when using the Automatic High Beam system
Observe the following to ensure that the Automatic High Beam functions
correctly.
● Do not overload the vehicle.
● Do not modify the vehicle.

3477-1. Maintenance and care
7
Maintenance and care
YARIS_F_WE_52G04E
NOTICE
■Cleaning detergents
● Do not use the following types of detergent, as they may discolor the vehi-
cle interior or cause streaks or damage to painted surfaces:
• Non-seat portions: Organic substances such as benzene or gasoline,
alkaline or acidic solutions, dye, and bleach
• Seats: Alkaline or acidic solutions, such as thinner, benzene, and alco-
hol
● Do not use polish wax or polish cleaner. The instrument panel’s or other
interior part’s painted surface may be damaged.
■ Preventing damage to leather surfaces
Observe the following precautions to avoid damage to and deterioration of
leather surfaces:
● Remove any dust or dirt from leather surfaces immediately.
● Do not expose the vehicle to direct sunlight for extended periods of time.
Park the vehicle in the shade, especially during summer.
● Do not place items made of vinyl, plastic, or containing wax on the uphol-
stery, as they may stick to the leather surface if the vehicle interior heats
up significantly.
■ Water on the floor
Do not wash the vehicle floor with water.
Vehicle systems such as the audio system may be damaged if water comes
into contact with electrical components such as the audio system above or
under the floor of the vehicle. Water may also cause the body to rust.
■ When cleaning the inside of the windshield (vehicles with front sensor)
Be careful not to touch the front sensor ( P. 223).
If the camera is accidentally scratched or hit, PCS, LDA and Automatic High
Beam may not operate properly or may cause a malfunction.
■ Cleaning the inside of the rear window
● Do not use glass cleaner to clean the rear window, as this may cause
damage to the rear window defogger heater wires. Use a cloth dampened
with lukewarm water to gently wipe the window clean. Wipe the window in
strokes running parallel to the heater wires.
● Be careful not to scratch or damage the heater wires.