2015 Ram 2500 bulb

2. Pull the outboard side of the lamp rearward farenough to unsnap the two receptacles on the outboard
side of the lamp housing from the two plastic snap
post retainers in the outer box side panel. 3. Disconnect the wiring harness connectors from the
bulb socket.
4. Rotate the bulb socket counterclockwise 1/4 turn to unlock it from the housing.
5. Pull the bulb straight out of the socket.
CAUTION!
Do not contaminate the bulb glass by touching it
with your fingers or by allowing it to contact other
oily surfaces. Shortened bulb life will result.
6. Reverse the procedure to install the bulb and housing.
Pulling Out The Tail Lamp
7
MAINTAINING YOUR VEHICLE 809

Center High-Mounted Stoplamp (CHMSL) With
Cargo Lamp
1. Remove the two screws holding the housing/lens tothe body as shown.
2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn the desired bulb socket ¼ turn and remove the
socket and bulb from housing.
4. Pull the desired bulb straight from the socket.
CHMSL Mounting Screw Locations
CHMSL Connector Location
810 MAINTAINING YOUR VEHICLE

CAUTION!
Do not contaminate the bulb glass by touching it
with your fingers or by allowing it to contact other
oily surfaces. Shortened bulb life will result.• Outside Bulbs: Cargo Lamps •
Inside Bulb: Center High-Mounted Stop Lamp
5. Reverse the procedure for installation of bulbs and housing.
Cab Top Clearance Lamps — If Equipped
1. Remove the two screws from the top of the lamp.
CHMSL Bulb And Socket
Removing Rear Screw From Clearance Lamp
7
MAINTAINING YOUR VEHICLE 811

2. Rotate the bulb socket ¼ turn and pull it from the lampassembly. 3. Pull the bulb straight from it’s socket and replace.
Removing Bulb Socket From Clearance Lamp
Removing The Bulb From The Bulb Socket
812 MAINTAINING YOUR VEHICLE

Rear Lamp Bar ID Marker (Dual Rear Wheels) — If
Equipped
1. Loosen the two screws and the housing to gain accessto the bulb sockets. 2. Turn the socket ¼ turn counterclockwise to access the
bulb.
3. Pull the bulb straight out from the socket.
4. Reverse the procedure for installation of the bulbs and housing.
Screw Locations
7
MAINTAINING YOUR VEHICLE 813

Side Marker Lamps (Dual Rear Wheels) — If
Equipped1. Push rearward on the side marker lamp assembly.
2. Pull the entire assembly from the fender.
3. Turn the socket ¼ turn counterclockwise and removefrom assembly to access the bulb.
4. Pull the bulb straight out from socket.
5. Reverse the procedure for installation of the bulbs and housing.
Side Marker Lamp Locations
814 MAINTAINING YOUR VEHICLE

Auto Down Power Windows..................47
Automatic Door Locks ......................39
Automatic Headlights ..................... .166
Automatic High Beams .....................168
Automatic Temperature Control (ATC) ..........413
Automatic Transmission .................455, 786
Adding Fluid ...................... .785, 786
Fluid and Filter Changes ..................786
Fluid Change ......................... .786
Fluid Level Check ................782, 783, 784
Fluid Type ........................ .782, 820
Shifting .......................... .464, 476
Special Additives ...................... .783
Axle Fluid .......................... .780, 820
Axle Lubrication ......................... .780
Back-Up Camera ......................... .207
Bar, Stabilizer/Sway System ..................524
Battery ................................ .760Keyless Transmitter Replacement (RKE)
........30
Belts, Seat ...............................115
Body Builders Guide ........................6
Body Mechanism Lubrication .................763
B-Pillar Location ......................... .597
Brake Assist System ...................... .577
Brake Control System, Electronic ..............575
Brake Fluid ......................... .779, 820
Brake System ........................ .575, 778
Anti-Lock (ABS) ....................... .576
Fluid Check .......................... .779
Master Cylinder ....................... .779
Parking ............................. .572
Warning Light ........................ .285
Brake/Transmission Interlock .................454
Bulb Replacement ..................... .804, 805
Bulbs, Light ..........................117,804
Cab Top Clearance Lights ...................811
10
INDEX 843

Information Center, Vehicle...............297, 325
Inside Rearview Mirror ..................126, 133
Instrument Cluster ....................... .285
Instrument Panel and Controls ................282
Instrument Panel Lens Cleaning ...............791
Integrated Trailer Brake Controls ..............654
Interior Appearance Care ....................790
Interior Lights .......................... .171
Intermittent Wipers (Delay Wipers) .............177
Introduction ..............................4
Inverter Outlet (115V) ..................... .230
Jack Location ........................ .683, 703
Jump Starting ........................... .725
Key Fob Programming Additional Key Fobs ...........21
Programming Additional Transmitters .........21
Key-In Reminder ..........................18 Keyless Enter-N-Go
.....................42, 443
Keyless Enter-N-Go™ .......................42
Lock The Vehicle’s Doors ..............359, 380
Passive Entry ...........................42
Passive Entry Programming ..........42, 359, 380
Keyless Entry System .......................25
Key, Replacement ..........................20
Keys ...................................12
Key, Sentry (Immobilizer) ....................19
Lane Change and Turn Signals ................175
Lane Change Assist ....................... .176
Lap/Shoulder Belts .........................53
Latches ................................117
Lead Free Gasoline ....................... .627
Leaks, Fluid .............................118
Life of Tires .............................611
Light Bulbs ..........................117,804
Lights ..............................117,164
850 INDEX