2015 Peugeot Partner Tepee fold seats

70
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
Never drive with the head
restraints removed; they must be
in place and correctly adjusted.Adjustable armrest
to access the vertical position, raise
the armrest until it locks.
Lower the armrest to return it to a
position for use.
to remove the armrest, press the
release
button from the vertical position
and move aside the armrest.
to put the armrest back in place, clip it
in the vertical position.
If the vehicle is fitted with the additional
console and an armrest, to fold the
passenger seat to the table position
remove the console or the armrest.
Front heated seats control
Each front seat may be fitted with a
control located on the side part of the
cushion.
Press to switch on the cushion heating.
Press again to switch it off.
Head restraint height adjustment
to raise the head restraint, slide it vertically

upwards.
to lower the head restraint, press the


button and slide the head restraint
vertically downwards.
t

he adjustment is correct when the upper
edge of the head restraint is level with the
top of the head.
to remove the head restraint, press the


button and pull the head restraint upwards.
to re-install the head restraint, engage


the rods in the holes making sure they are
aligned with the seat back.
Seats

71
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
REAR BENCH SEAT
each 1/3 - 2/3 section can be folded
fully , then removed individually.
Head restraint
High position: lift and raise the head
restraint.
Low position: press on the head
restraint to lower it.
to remove the head restraint, after
raising it press the tab and lift the head
restraint.
to install the head restraint, engage
the rods of the head restraint in the
holes keeping it in line with the seat
back.
The 1/3 - 2/3 rear bench seat is fitted
with "comma" shape head restraints.
Seats
eASe OF uSe and COMFORt
4

72
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
Fully folded position
example of operations for the
1/3 section. t hey are identical for the
2/3 section.
-

Place the head restraints in the low
position.
-


If necessary
, move the front seats
forward.
-

Press the grey control located on
the upper part of the seat back.
-


Fold the seat back onto the seat
cushion. -


Raise the grey control bar
, located
at the rear of the seat cushion.
- t
ilt the entire seat forward.
Putting back in place
tilt the entire seat rearwards until it
locks.
Raise the seat back.
t

he seat is locked correctly when the
control (at the top of the seat back) is
no longer visible.
Check that the seat is locked
on the floor securely when it is
returned to the sitting position.
Seats

73
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
Removing the bench seat
- If necessary, move the front seats
forward.
- Place the bench seat (1/3 section and/or
2/3 section) in the fully folded position.
Refitting the bench seat
- Offer up the bench seat (1/3 section and/or 2/3 section) vertically.
-

Place the hooks between the two
bars.
-


Fold the bench seat rearwards.
Refer to the "fully folded position"
described on the previous page.
to return the bench seat
(1/3

section and/or 2/3 section)
to the "passenger transportation"
position, refer to the "fully folded
position" described on the previous
page.
-
t
ilt the entire seat rearwards by
approximately 45°.
-


Lift the bench seat

vertically to the
limit of the anchorages.
-

Straighten bench seat by tilting it
forwards then lift it.
Seats
eASe OF uSe and COMFORt
4

74
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
REAR SEATS (5 SEAT VERSION)Head restraint
High position: lift and raise the head
restraint.
Low position: press on the head
restraint to lower it.
to remove the head restraint, after
raising it press the tab and lift the head
restraint.
to install the head restraint, engage
the rods of the head restraint in the
holes keeping it in line with the seat
back.
e

ach seat can be removed individually.
e

ach time a seat is returned to the
sitting position or after removing then
refitting a seat, check that it is locked
on the floor securely.
t

he three independent rear seats
are fitted with "comma" shape head
restraints.
t

he back of the centre seat, folded
onto the seat cushion, has a shell
which serves as a table with cup
holder.
Seats

75
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
Adjusting the angle of the seat back
- Operate the control and adjust the
angle of the seat back.
Placing the seat back in the
table position
- Pull the control to fold the seat back
onto the seat cushion.
Do not place hard or heavy objects
on the table.
t

hey could become
dangerous projectiles in the event of
sharp braking or impact.
Returning the seat back to the
sitting position
- Release the seat back by pulling the
control, then return it to its original
position.
When returning the seat back to the sitting
position, ensure that it is locked securely.
Placing the seat in the fully
folded position
- Pull the control to place the seat
back in the table position.
-

Raise the bar located behind the
seat to release the rear anchoring
points.
-

t
ilt the entire seat forwards, until it
locks.
Returning the seat to its original
position
- Push the red control.
-
Fold back the seat to fix the rear
anchoring points.
-


Raise the seat back by pullin
g the
control.
Check that the entire seat is anchored
securely.
Seats
eASe OF uSe and COMFORt
4

76
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
Removing the seat
- If necessary, move the front
seats forward and lower the head
restraint.
-

Place the seat in the fully folded
position.
Good practice
Following the various operations:
-
do not remove a head restraint
without storing it and fix it to a
support,
-


ensure that the passengers can
always access the seat belts and
fasten them easily

,
-

passengers must never take
their seat without adjusting and
fastening their seat belt.
Refer to the "fully folded position"
described on the previous page.
-


Press the red lever to release the
front feet.
-

t
ilt the entire seat rearwards by
approximately 45° without releasing
the lever

.
-

Release the lever

.
-

Lift the seat

vertically to the limit of
the anchorages.
-

Straighten the seat by tilting it
forwards then lift it.
Putting the seat back in place
- tilt the seat forward by 45°.
-
Place the hooks between the

two bars.
-

Fold back the seat to fix the rear
anchoring points.
-


Pull the control to return the seat
back to its initial position.
-


Raise the head restraint.
Check that no object is obstructing
the anchoring recesses or preventing
correct locking of the seats.
Seats

79
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
Adjusting the angle of the seat back
-
Operate the control and adjust
the

angle.
Placing the seat in the table position
-

Lower the head restraint fully
.
-

Operate the control to fold the seat
back onto the seat cushion. Returning the seat back to the
sitting position
-


Release the seat back by pullin
g
the control, then return it to its
original position.
e
nsure that the entire seat is anchored
securely.
Placing the seat in the fully folded
position
-
Place the seat in the table position.
-


Pull the red strap, located behind
the seat, to release the feet of the
seat from their anchorage on the
floor

.
-
t
ilt the entire seat forwards.
Row 2 seat adjustmentsReturning the seat to its original
position
-
Fold back the entire seat.
Before folding the seat, ensure
that:
-


in row 3, no passenger's
foot is at one of the seat
anchorages on the floor

,
-

the seat is locked securely on
the floor

,
-

the seat belt is available for
the passenger

.
Seats
eASe OF uSe and COMFORt
4