Page 9 of 176
7
Ion_en_Chap00b_vue-ensemble_ed01-2014
Instruments and controls
1. Steering lock and ignition switch.
2. Wiper stalk.
3.
 W
indscreen demisting vents.
4.
 G
love box.
 P
assenger's airbag deactivation.
5.
 B
onnet release lever.
6.
 P
arking brake.
7.
 D
rive selector.
8.
 1
2 V accessory socket.
9.
 H
eating / air conditioning controls.
10.
 E
mergency or assistance call.
11.
 H
azard warning switch.
12 .
 C
entre vents.
13.
 A
udio system.
. 
Over view  
     
        
        Page 12 of 176
10
Ion_en_Chap01_controle-de-marche_ed01-2014
Indicator and warning lamps
Visual indicators informing the driver that 
a  system is in operation, is deactivated or has 
a fault.Associated warnings
The illumination of certain warning lamps may 
be accompanied by an audible signal.
The warning lamps may come on continuously 
(fixed) or flash.
Certain warning lamps may come on in 
one of two modes. Only by relating the 
type of lighting to the operating status 
of the vehicle can it be ascertained 
whether the situation is normal or 
whether a fault has occurred.
When the ignition is switched on
Certain warning lamps come on for a few 
seconds when the vehicle's ignition is  
switched on.
These same warning lamps go off after a few 
seconds.
If you notice one of these warning lamps 
remaining on, refer to the information on the 
warning lamp in question. 
Monitoring  
     
        
        Page 19 of 176
17
Ion_en_Chap01_controle-de-marche_ed01-2014
AirbagsOn temporarily. When you switch on the ignition, this 
warning lamp comes on for a few 
seconds, then goes off. If it does not go off, contact a PEUGEOT dealer or a 
qualified workshop.
On fixed. Fault with one of the airbag or seat 
belt pretensioner systems. Have it checked by a PEUGEOT dealer or a qualified 
workshop.
Protection 
system for the 
main battery On fixed.
The state of charge of the main 
battery is too low or the temperature 
of the main battery is too low... The power from the motor is limited.
Charge the main battery as soon as possible.
If the warning lamp does not go off, contact a 
PEUGEOT dealer or qualified workshop.
Self-diagnosis 
system of the 
main electrical 
circuit On fixed.
Fault in the main electrical circuit. You must stop as soon as it is safe to do so.
Have it checked by a PEUGEOT dealer or a qualified 
workshop.
Warning / indicator lamp
StateCause Action / Observations
1 
Monitoring  
     
        
        Page 21 of 176
19
Ion_en_Chap01_controle-de-marche_ed01-2014
Energy consumption / generation indicator
Energy consumption
On switching on the ignition, your vehicle 
neither consumes nor generates energy in its 
electric traction system: the needle is in the 
"neutral" position (provided that the heating and 
air conditioning are off).
"Eco" zone
A system that informs the driver of the level of energy consumption or generation of the main battery.
"Neutral" position"Charge" zone
The needle moves to the right in proportion to 
the energy consumption by the vehicle.The needle is in this zone when the vehicle is 
used so as to moderate electric consumption 
and optimise its range.
The needle moves to the left in proportion to 
the level of charge sent to the main battery, 
during period of deceleration and braking.
1 
Monitoring  
     
        
        Page 22 of 176
20
Ion_en_Chap01_controle-de-marche_ed01-2014
Instrument panel screenWhen the ignition switch is in the "ON" position, press button A repeatedly to display the following information in turn.
Distance recorder
System for measuring the total distance 
travelled by the vehicle during its life.
Press button A .
The total distance appears in the screen.Reset to zero
With the ignition on and either trip A or B 
displayed, press the button for more than 
2
 
seconds.
Trip distance recorder (Trip A or B)
Each of these trip recorders indicates the 
distance travelled since the last reset.
Press button A to display the desired trip. 
Monitoring  
     
        
        Page 23 of 176

21
Ion_en_Chap01_controle-de-marche_ed01-2014
Service indicator
When the ignition is switched on, press 
button  A several times in succession until the 
service indicator is displayed in the desired 
units. This point can be indicated in one of two ways:
-  
t
 he miles (km) remaining,
-  
t
 he time remaining to the next service.
Operation
1. The screen indicates that 620 miles 
(1000   km) or 1 month remain before the 
next service.
2.
 T
he screen indicates that the date for the 
service has been exceeded.
 E
very time the ignition is switched on, 
the service spanner is displayed for a 
few seconds to remind you that a service 
should be carried out as soon as possible.
3.
 O
nce the service has been carried out, the 
distance or the number of months to the 
next service is displayed again.
System which informs the driver when the 
next service is due in accordance with the 
manufacturer's servicing schedule.
The point at which the next service is due is 
calculated from the last service indicator zero 
reset.
System for manual adjustment of the 
brightness of the instruments and controls in 
relation to the exterior brightness.
With the lighting on or off, press button A to 
select the function, then hold down to change 
the intensity of the lighting of the instruments 
and controls in "day" or "night" mode.
The intensity of the lighting increases each time 
button A is pressed.
When the lighting reaches the maximum 
setting, press again to change to the minimum 
setting.
When the lighting reaches the required 
intensity, release button A .
The setting is saved when you release button A 
and retained when the ignition switch is turned 
t o  O F F.
Lighting dimmer
1 
Monitoring  
     
        
        Page 24 of 176
22
Ion_en_Chap01_controle-de-marche_ed01-2014
The display of "---", indicating that the 
service date has arrived, comes on 
automatically after a certain time and 
distance travelled. The screen then 
indicates the time remaining before the 
next service is due.
Resetting the service indicator to zero
After each service, the service indicator should 
be rest to zero.
The procedures is as follows:
F
 
S
 witch off the ignition (switch in the LOCK 
or ACC position).
F
 
P
 ress the reset button A several times in 
succession until the service indicator is 
displayed.
F
 
P
 ress and hold the reset button for a few 
seconds until the spanner flashes .
F
 
P
 ress the reset button while the spanner is 
flashing to change the display from "---"  to 
"CLEAR" .
 T
he distance (or time) remaining before the 
next service is due is displayed. 
Monitoring  
     
        
        Page 27 of 176
25
Ion_en_Chap02_ouvertures_ed01-2014
Anti-theft protection
Electronic immobiliser
The key contains an electronic chip which has 
a special code. When the ignition is switched 
on, this code must be recognised to permit 
starting.
This electronic immobiliser locks the control 
system a few moments after the ignition is 
switched off and prevents starting by anyone 
who does not have the key.
In the event of a malfunction and if your vehicle 
does not start, contact a PEUGEOT dealer as 
soon as possible.
Remote control problem
In the event of a remote control malfunction, 
you can neither unlock nor lock your vehicle.
F 
F
 irst of all, use the key in the driver's door 
lock to unlock or lock your vehicle.
F
 
T
 hen, contact a PEUGEOT dealer to check 
the operation of the remote control and 
replace the battery if necessary.
2 
Access