2015 PEUGEOT BOXER ignition

47
HEAdLAMP BEAM
You are advised to adjust the height of the
headlamp beams in accordance with the
load in your vehicle.
this function works in the dipped and main

beam headlamps position.
Press these controls, located
on the dashboard, several times
in succession to adjust the
headlamps.
An indicator in the screen shows
the adjustment position selected
(0, 1, 2, 3).
PArKInG LAMPS
this system enables you to leave the lamps
on when parked; with the ignition off, key in
the S
tOP position or key removed.
Move the ring on the lighting stalk to


position
O then to dipped or main beam


headlamps.
the

indicator lamp in the
instrument panel comes on.
the lamps will remain on while


you are parked.
Leaving the lighting on for long periods may
significantly reduce the state of charge of
your vehicle's battery.
travelling abroad
If using your vehicle in a country
that drives on the other side of the road,

the headlamps must be adjusted to avoid
dazzling on-coming drivers.
Contact a P
eugeOt dealer or a qualified
workshop.
3
EASE oF uSE and coMFort
Steering mounted controls

48
WIPEr controL StALKSlow continuous wiping: 2 notches downwards.Do not cover the rain sensor, located at
the top centre of the windscreen.
Screenwash and headlamp wash
Pull the wiper control stalk towards you,
the screenwash is accompanied by a timed
operation of the wipers.
Depending on version, the headlamp wash is
coupled with the screenwash, it is triggered if
the dipped beam headlamps are on.
Windscreen wipers
Wiping is only active when the ignition key is
in the
runnInG
position.
the control stalk has five dif

ferent positions:
Wipers off.
Intermittent wiping: 1 notch downwards.
In this position, four wiping frequencies can
be selected by turning the ring: -
very slow frequency
-
slow frequency
-
standard frequency,
-
fast frequency.
Automatic rain sensitive windscreen
wipers
If your vehicle is fitted with this system, the
wiping speed is adapted automatically to the
intensity of the rainfall.
Automatic wiping: 1 notch downwards.
this is confirmed by one wipe. Must


be reactivated each time the ignition is
switched
on.
In this position, the sensitivity of the rain


sensor can be increased by turning the ring.
Good practice
Check that the windscreen wiper blades can
operate freely when using the wipers in icy
weather.
use the step in the front bumper

, to remove
any accumulation of snow at the base of the
windscreen and on the blades.
You can change the wiper blades.
Refer to the "Quick help - Worn wiper
blade" section.
You can check the fluid level.
Refer to the "Checks - Levels and
checks" section.
Fast continuous wiping: 3 notches
downwards.
Single wipe: pull the control stalk towards
the steering wheel.
With Stop & Start, when the wiper
control stalk is in the fast wipe position,


the S
tOP mode is not available.
When washing the vehicle, switch of

f the
ignition or deactivate the automatic rain
sensitive wipers.
Steering mounted controls

51Good practice
When changing the programmed reference
speed by pressing and holding the control,
take care as the speed may increase or
decrease rapidly.
Do not use the cruise control on slippery
roads or in heavy traffic.
On a steep gradient, the cruise control will
not be able to prevent the vehicle from
exceeding the programmed speed.
the cruise control cannot, in any

circumstances, replace the need to comply
with speed limits or vigilance on the part of
driver.
It is advisable to leave your feet near the
pedals.
to prevent the mat from becoming caught
under the pedals:
-
ensure that the mat is positioned
correctly

,
-
never fit one mat on top of another.
cancelling the programmed speed
When the vehicle stops, after the ignition is
switched off, the system no longer stores
any speed.
operating fault
In the event of a fault, the system
is switched off and the indicator
goes off.
Contact a P
eugeOt dealer or a qualified
workshop to have the system checked.
3
EASE oF uSE and coMFort
Steering mounted controls

54
there are two methods of memorising a
speed higher than the previous one:
Without using the accelerator:
-
Move the switch up (+).
A brief press increases the speed by


1 mph (km/h).
A maintained press increases the speed in
steps of 5 mph (km/h).
using the accelerator:
-
exceed the memorised speed until the
speed required is reached,
-
move the switch up (+) or down (-).
to memorise a speed lower than the
previous one:
-
move the switch down (-).
A brief press decreases the speed by


1 mph (km/h).
A maintained press decreases the speed in
steps of 5 mph (km/h).
changing the
programmed
speed Switching the system off
- Place the ring in the central o position
or switch of f the ignition to switch the
system off.
When the vehicle becomes stationary, after
switching off the ignition, the system no
longer memorises a speed.
operating fault
In the event of a fault, the system
switches off and the indicator
goes off. Contact a P
eugeOt
dealer or a qualified workshop to
have the system checked.
Good practice
When changing the programmed reference
speed by means of a maintained press,
pay attention as the speed can increase or
decrease rapidly.
Do not use the cruise control on slippery
roads or in heavy traffic.
In the event of a steep slope, the cruise
control cannot prevent the vehicle from
exceeding the programmed speed.
In any event, the cruise control cannot
replace the need to observe the speed
limits, nor can it replace the need for
vigilance on the part of the driver.
It is advisable to leave your feet near the
pedals.
to avoid any jamming under the pedals:
-
ensure that the mat and its fixings on the
floor are positioned correctly

,
-
never place one mat on top of another.
Steering mounted controls

57
Exceeding the programmed
speed
Pressing the accelerator pedal in order to
exceed the programmed speed will have
no effect unless you press the pedal firmly
beyond the point of resistance.
If the limiter is unable to prevent an increase
in the speed of the vehicle because of the
profile of the road or when going down a
step hill, the programmed speed may be
exceeded.
the limiter is deactivated temporarily and


the programmed speed flashes.
to return to the limiter function, reduce your
speed to below the programmed speed.
Switching the system off
- Place the ring in the central o position
or switch of f the ignition to switch the
system off.
the last programmed speed remains in the


memory.
operating fault
the programmed speed is cleared then
replaced by dashes.
Contact a P
eugeOt dealer or a qualified
workshop to have the system checked.
Good practice
In any event, the speed limiter cannot
replace the need to observe speed limits,
nor can it replace the need for vigilance on
the part of the driver.
Always pay attention to the profile of the
road and sharp acceleration and stay in
complete control of your vehicle.
to avoid any jamming under the pedals:
-
ensure that the mat and its fixings on the
floor are positioned correctly

,
-
never place one mat on top of another.
3
EASE oF uSE and coMFort
Steering mounted controls

65AddItIonAL HEAtInG SYStEMS
Supplementary heating
On the 2-3 seats version, this is located
under the seat on the driver's side with air
diffusion directed forwards.
rEAr HEAtInG And/or AIr
condItIonInG
If your vehicle is fitted with an additional
air conditioning unit, located in the rear of
the vehicle: the distribution duct located in
the roof and the individual diffusion vents
provide a perfect diffusion of cold air.
the warm air dif

fused at the floor, from the
front air conditioning unit, is distributed at
the feet of the rear passengers of rows 2
and 3.
A warm air diffusion vent, located on the rear
left wheelarch, may complete the assembly
for the feet of the rear passengers of row 3.
Additional heating
this is passenger compartment heating,
additional to the standard equipment.
It can operate independently of the engine.
Additional heater or programmable
additional heating
this is an additional, programmable and
separate system which heats the Diesel
engine hot coolant loop to make starting

easier.
It improves the demisting and defrosting
performance and that of the heated seats, if
fitted to the vehicle.
the passenger compartment heating is


brought up to temperature more rapidly.
this system must be programmed to start up


before you enter the vehicle. On the 5-9 seats version, it is
located at the rear. Depending
on the model version, the air
diffusion is either direct from the
rear or comes from the rail located under
each of the two rows of seats.
Press this control to activate/
deactivate the heating.
the LeD


is on if the heating is activated.
When rapid demisting and
defrosting is required, switch off the control.
Automatic additional heating
this is an additional system which starts
automatically when the ignition is switched
on. Its activation depends on the ambient

temperature and the temperature inside the
vehicle.
It switches off automatically once the
heating system is started manually.
3
EASE oF uSE and coMFort
Ventilation

80
reading lamps
these are controlled by the switches.
the driver's switch controls both reading

lamps simultaneously.
the passenger switch controls either the


driver's reading lamp or the passenger
reading lamp.
courtesy lamp
this can be activated by means of:
-
the switches located on the courtesy
lamp, with the ignition on -
runnInG
position,
-
opening or closing one of the front
doors,
-
locking/unlocking the vehicle.
It switches off automatically:
-
if the switch is not pressed to the right or
to the left,
-
in all cases after 15 minutes, if the doors
remain open,
-
or when the ignition is switched on. Switches at the bottom of the
dashboard on the driver's side


allow the driver to switch the
passenger reading lamp on
and
of

f.
overhead storage compartment
this is located above the sun visors.
Maximum load: approximately 20 kg.
Practical information

83
Sliding side windows
Depending on the vehicle's equipment, the
side windows of row 2 can be opened.
Squeeze the two controls then slide the
window.
torch
If your vehicle has one, the magnetic torch is
located at the rear courtesy lamp.
A lamp is locatred in the centre of the torch
base.
Remove the torch from its base by
pressing the button then pivoting the torch
downwards by 90 degrees.
to switch on the torch, slide the switch
forwards.
to change the 4 batteries (NiMH type),
remove the protective cover

, located on the
torch. With the vehicle stationary, key in the
ignition switch or removed, recharging
and lighting from the torch stops after
around 15 minutes.
the torch batteries recharge automatically

while driving.
to put the torch back in place, engage
it in the notches on the base and pivot it

upwards.
While driving, the window must be closed
or secured in an intermediate position.
Do not extend long objects outside the
vehicle via the window

.
3
EASE oF uSE and coMFort
Practical information